Check pin count value from pin status and stop verification the pin if
the value is less then 3. This should prevent the proto-handler to
lock the SIM. If SIM is locked then the PUK is needed.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Load the json output from uqmi --get-pin-status command and evaluate the
"pin1_status" value.
The following uqmi "pin1_status" values are evaluated:
- disabled
Do not verify PIN because SIM verification is disabled on this SIM
- blocked
Stop qmi_setup because SIM is locked and a PUK is required
- not_verified
SIM is not yet verified. Do a uqmi --verify-pin1 command if a SIM is
specified
- verified:
Do not verify the PIN because this was already done before
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
QMI proto setup-handler will wait forever if SIM does not get initialized.
To fix this stop polling pin status and notify netifd. Netifd will generate
then a "ifup-failed" ACTION.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
QMI proto setup-handler will wait forever if it is unable to registrate to
the mobile network. To fix this stop polling network registration status
and notify netifd. Netifd will generate then a "ifup-failed" ACTION.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This value will be used for now during following situations:
* Ask the sim with the uqmi --get-pin-status command.
* Wait for network registration with the uqmi --get-serving-system command.
This two commands wait forever in a while loop. Add a timeout to stop
waiting and so inform netifd.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Move uqmi std and error output on commands without using them to /dev/null.
This will remove useless outputs in the syslog.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Allow setting specific routing tables via the ip4table and ip6table
options also when ${ifname}_4 and ${ifname}_6 child interfaces are
being created.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The control device /dev/cdc-wdm0 is not available immediately on the
D-Link DWR-921 Rev.C3, therefore the wwan interface fails to start at
boot with a "The specified control device does not exist" error.
This patch alters /lib/netifd/proto/qmi.sh to wait for
network.wwan.delay earlier, before checking for the control device,
instead of just before interacting with the modem.
One still has to use network.wwan.proto='qmi', as the "wwan" proto
performs that sort of check before any delay is possible, failing with a
"No valid device was found" error.
Signed-off-by: Thomas Equeter <tequeter@users.noreply.github.com>
Pipe uqmi output from qmi_wds_stop function into /dev/null.
This will supress the following output in proto teardown.
netifd: wwan (x): "No effect"
netifd: wwan (x): Command failed: Permission denied
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The current implementation only checked if uqmi itself executed
correctly which is also the case when the returned value is actually
an error.
Rework this, checking that CID is a numeric value, which can only
be true if uqmi itself also executed correctly.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
uqmi contains a command for directly querying the modem if there
is a valid data connection, so let's use it.
This avoids the cases were all previous tests are succesful, but the
actual data link is not up for some reasons, leading to states were we
thought the link was up when it actually wasn't ..
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Originally, the implementation only checked if uqmi command
execution succeeded properly without actually checking it's returned data.
This lead to a pass, even when the returned data was indicating an error.
Rework the verification to actually check the returned data,
which can only be correct if the uqmi command itself also executed correctly.
On command execution success, value "pdh_" is a pure numeric value.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Debugging shows that using the general method properly cleans on each
run, while the method specifying the client-ID shows "No effect"
even while in connected state.
Fixes several connectivity issues seen on specific modems.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
If a device only supports the 2nd verification method (uim),
the first method will fail as expected reporting an error:
"Command not supported"
Silence both separate methods and only report an error regarding
pin verification if both fail.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Some newer LTE modems, like the MC7455 or EC25-E do not support
"802.3" mode, and will stay in "raw-ip" regardless of the mode being
set.
In this case, the driver must be informed that it should handle all
packets in raw mode. [1]
This commit fixes connectivity issues for these devices.
Before:
[ Node 5 ] udhcpc -i wwan0
udhcpc: started, v1.27.2
udhcpc: sending discover
udhcpc: sending discover
udhcpc: sending discover
After:
[ Node 5 ] udhcpc -i wwan0
udhcpc: started, v1.27.2
udhcpc: sending discover
udhcpc: sending select for 100.66.245.226
udhcpc: lease of 100.66.245.226 obtained, lease time 7200
udhcpc: ifconfig wwan0 100.66.245.226 netmask 255.255.255.252 broadcast
+
udhcpc: setting default routers: 100.66.245.225
[1] https://lists.freedesktop.org/archives/libqmi-
devel/2017-January/002064.html
Tested on cns3xxx using a Sierra Wireless MC7455 LTE-A
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[bumped PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Newer devices tend to only support the newer version of the pin
verification command, so also try that one.
Fixes PIN issues with modems like the Sierra Wireless MC7455
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
If you unplug a QMI device, the /dev/cdc-wdmX device
disappears but uqmi will continue to poll it endlessly.
Then, when you plug it back, you have 2 uqmi processes,
and that's bad, because 2 processes talking QMI to the
same device [and the same time] doesn't seem to work well.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This reverts the following commits:
fbe522d120278ad007ee863888e44f96daf6352fcfd83555fc
This seems to trigger some mconf bugs when built with all feeds
packages, so I will try to find a less intrusive solution before the
release.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
uqmi has the possibility to allow the modem to start a regsitration
process only to this specified plmn
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Add uqmi 'sync' command call to release stalled cid when preparing to
setup new connection. As a result it prevents 'POLICY MISMATCH' errors.
Signed-off-by: Nickolay Ledovskikh <nledovskikh@gmail.com>
8ceeab6 uqmi: Change returned value to QMI_CMD_REQUEST for 'sync' command.
1dc7be1 uqmi: Add sync command to release all cids.
Signed-off-by: John Crispin <john@phrozen.org>
It's useful when using multiple usb devices that should be bound to
certain usb ports. Symlinks are created by hotplug handlers.
Signed-off-by: Nickolay Ledovskikh <nledovskikh@gmail.com>
Update uqmi to latest version, which brings about support for
specifying a call profile index instead of APN. A specific index
different from 1 must be used for some service provider and modem
combinations.
Also change option dhcp to dhcpv6, since IPv4 now always uses DHCP,
replace option ipv6 with pdptype, which is less ambiguous, and
make autoconnect optional and default it to off for IPv6 due to it
not working with statically configured IPv6.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
Commit 8f24ee6382 ("uqmi: Add proper IPv6 support") changed the code
to fetch the IPv4 address via QMI by default instead of using DHCP to
make it consistent with the IPv6 codepath.
This breaks on at least some Sierra Wireless cards, where data exchanges
fail to work until the host has fetched a DHCP lease.
Leave v6 as it is, but always use DHCP for v4.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Change git packages to xz
* Update mirror checksums in packages where they are used
* Change a few source tarballs to xz if available upstream
* Remove unused lines in packages we're touching, requested by jow- and blogic
* We're relying more on xz-utils so add official mirror as primary source, master site as secondary.
* Add SHA256 checksums to multiple git tarball packages
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
If option ist not set then ipv6 is still enabled on this Interface.
Check if variable is zero will fix this issue.
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Using protocol qmi does not work since qmi.sh is not executable.
Setting option dhcp explicitely to 0 actually enables it.
This patch fixes both problems.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 47014
Use the new --ip-family option to start both IPv4 and IPv6 sessions
by default. Autoconnect can't be used when starting two sessions,
so revert back to using the client IDs and packet data handles for
handling the network connection.
Some modem firmwares do not implement a RA server, therefore by
default use outband IP configuration and static addressing. Some
other firmwares report bogus IP configuration with the WDS get
current settings command. In this case inband configuration with
DHCP/RA can be optionally enabled by setting option dhcp to 1.
Per 3GPP standard a /64 prefix is served to all clients, which is
extended to LAN as specified in RFC 7278.
v2: Restrict the IPv6 gateway route source address
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46843
The wwan package holds the hotplug script to set mobile broadband
interfaces (un)available. Add it as a dependency to comgt-ncm,
uqmi and umbim.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44631
Added complementary blobmsg_close_table() before returning from function
on error.
Signed-off-by: Sławomir Demeszko <s.demeszko@wireless-instruments.com>
SVN-Revision: 43477
