Commit graph

3606 commits

Author SHA1 Message Date
Daniel F. Dickinson
7a3e133751 ar71xx: ag71xx: Prevent kernel oops for board def
The driver is written in such a way that with a board defintion that
connects a fixed phy, mdio, and switch in a certain way, a kernel oops could
result because of lack of previously probed mdio bus.

This commit allows for easier debugging in this case by casting the
correct blame with serial console messages.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:36 +02:00
Daniel F. Dickinson
0b9f4e8808 ar71xx: ag71xx: Add connect message: fixed phy
It's a little noisier but makes it obvious when the ar7240 switch was
connected to the MDIO bus, and to which phy device (or the failure
to do so).

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:35 +02:00
Daniel F. Dickinson
2655fbe8ef ar71xx: ag71xx_phy: Fix compilation for debug messages
NB: Error only appears with ag71xx debug messages and dynamic printk
enabled.  This is probably why no one has caught it before.

Previously phy probe debug messages used old (now wrong) functions
to get the phy name for printing.  There was also the chance of
a NULL pointer in the event no phy_device was found.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:35 +02:00
Daniel F. Dickinson
098267db4c ar71xx: cap324: Drop support for defunct cloud
Only build images for straight OpenWrt (using all flash; wipes out
partitions that contain information only important for accessing a
now defunct cloud service with the stock firmware) since the stock
firmware is now irrelevant.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:33 +02:00
Daniel F. Dickinson
37ab944ac5 ar71xx: cap324: Use correct company name
It's 'PowerCloud Systems' not just 'PowerCloud'

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson
739eaae9ca ar71xx: cap324: Use correct MAC addresses
The wrong MAC addresses (from the point of view of the physical device
label) were being assigned to the wrong interfaces.  Fix that.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson
d2f7dba309 ar71xx: cap324: Use standard eth as static lan
While the stock firmware and previous ar71xx versions of openwrt used the
single ethernet port as a DHCP client, for unmodified openwrt usage it
makes more sense to do the standard openwrt thing and make the ethernet
port a static lan with known address so that users can find the device on
the network more easily.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson
fedc826c32 ar71xx: cr5000: use correct company name
It's 'PowerCloud Systems' not just 'PowerCloud'

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson
50caf9d452 ar71xx: cr5000: Drop support for defunct cloud
The Skydog cloud service no longer exists hence supporting going back
to stock firmware with cloud support is no longer applicable.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson
c666851ce7 ar71xx: cr5000: Tweak switch LED settings
This is basically cosmetic and sets the Port 1-4 LEDs to blink on
10/100/1000M.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson
ffc71cd2d0 ar71xx: cr5000: Fix the reset button as KEY_RESTART
The reset button was incorrectly returning KEY_WPS_BUTTON as the key
code.  We want KEY_RESTART., so make that fix.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson
a208e07790 ar71xx: cr5000: board data: Use better macro name
The PCIe wireless MAC address address is better labelled as WMAC
than MAC to emphasize that it is for a wireless interface.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Thibaut VARÈNE
091e915d99 ar71xx: improve MikroTik wAP R support
81d446b045 introduced incomplete
support for this device.

This patch attempts to correct the situation based on OEM source
code.

LED1-3 are GSM mode on OFW (2G/3G/4G) hence unassigned here.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: David Ehrmann <ehrmann@gmail.com>
2018-07-30 10:35:11 +02:00
Thibaut VARÈNE
5c2419b6f8 ar71xx: add missing diag LED support for RB wAP 2nD
3b15eb06c3 did not include diag.sh
edit

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 10:35:11 +02:00
Thibaut VARÈNE
e76c048d34 ar71xx: rbspi: mark rb911L user led as active low
The active_low flag was missing for the user LED. This LED is open drain
(confirmed in OEM source) and open drain only makes sense for active low
GPIOs.

The two wireless LEDs mentioned in the comments are also #defined for
future reference.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Ryan Mounce <ryan@mounce.com.au>
2018-07-30 10:35:11 +02:00
Thibaut VARÈNE
e99f760235 ar71xx: rbspi: fix RB wAP AC gpio conflict and LED
e15c63a375 introduced code that was trying
to register GPIO 1 as both an LED and a button. The OEM source makes it
clear that LED1 is not wired to the SoC GPIOs. GPIO 1 is the reset button.

Furthermore the (green) power led default state should also be defined,
(matching OEM source), and it should be used by diag.sh since it's
currently the only software-controllable LED.

This patch fixes these issues and renames the corresponding #defines for
clarity

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 10:35:11 +02:00
Thibaut VARÈNE
03562bfcdb ar71xx: rbspi: clarify USB power gpios action
The gpios that control power toggle for USB on the RouterBOARD devices
are active low _off_ switches.

When they are active (low), power is off. When they are inactive
(high), power is on.

Rename GPIO defines, set gpios to GPIOF_ACTIVE_LOW for consistency and
reflect their true action in the display name. This brings openwrt code
in line with OEM.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Ryan Mounce <ryan@mounce.com.au>
2018-07-30 10:35:11 +02:00
Kin Chan
18b87b10a9 ar71xx: Move F9K1115v2 under ar71xx tiny target
F9K1115v2 has a kernel partition size of 1408 kB.

Since kernel 4.9.x+ the kernel image for this device compiled had exceeded
the kernel partition size limit and thus failing size check.

The kernel image generated for this device
under ar71xx tiny target is 1329.67 kB < 1408 kB.

Signed-off-by: Kin Chan <kcchan1@outlook.com>
2018-07-16 15:12:19 +02:00
Thibaut VARÈNE
c2d2647c09 ar71xx: add support for MikroTik RB931-2nD
This patch adds support for the MikroTik RB931-2nD (hAP mini):
https://mikrotik.com/product/RB931-2nD

Specifications:
  * SoC: Qualcomm QCA9533 (650MHz)
  * RAM: 32MiB
  * Storage: 16MiB SPI NOR flash
  * Ethernet: 3x100M
  * Wireless: QCA9533 built-in, dual-chain 802.11b/g/n

Installation:

1. Setup a DHCP/BOOTP Server with the following parameters:
   * DHCP-Option 66 (TFTP server name): pointing to a local TFTP
     server within the same subnet of the DHCP range
   * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
     of the to be booted image. The usable intramfs files are:
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
       - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin

2. Press the reset button on the board and keep that pressed.

3. Connect the board to your local network via its Internet port.

4. Release the button after the LEDs on the board are turned off.
   Now the board should load and start the initramfs image from
   the TFTP server.

5. Now connect the board via either of its LAN ports (2 or 3).

6. Upload the sysupgrade image to the board with scp:
     $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin

7. Log in to the running system listening on 192.168.1.1 via ssh
   as root (without password):
     $ ssh root@192.168.1.1

8. Flash the uploaded firmware file from the ssh session via the
   sysupgrade command:
     root@OpenWrt:~# sysupgrade /tmp/fw.bin

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-16 15:12:17 +02:00
Mathias Kresin
621fa91a82 ar71xx: move boards to tiny subtarget
Move boards to the tiny subtarget which break the build if the kernel is
set to "Optimize for performance".

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-12 18:15:19 +02:00
Mathias Kresin
a28d686fb6 ar71xx: factor out safe loader image build code
Add a template for safeloader images and include it instead of
overwriting variables defined in the common tp-link build commands.

Split the existing tp-link templates to proper implement the safeloader
template.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-07 21:07:40 +02:00
Mathias Kresin
b908c82f49 ar71xx: drop unnecessary LOADER_TYPE variables
Drop the LOADER_TYPE variables in case no loader is used at all or move
the variable to devices which are using a loader.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-07 21:07:40 +02:00
Mathias Kresin
a0ec632f8d ar71xx: get rid of copy-file
Use the provided image build variables to point the kernel-bin build
command to the kernel we are interested in.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-07 21:07:40 +02:00
Mathias Kresin
5260c1003c ar71xx: mikrotik: cleanup nand image build code
Use the LOADER_TYPE variable to specify that we need the elf preloader
and append the loader via the corresponding build recipe. It allows to
enable initramfs images again for mikrotik NAND images, which caused a
build error before.

Add the minor header only to the kernel of the sysupgrade images, as it
is only required for the bootloader to find the kernel on flash.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-07 21:07:40 +02:00
Koen Vandeputte
8e622aae58 kernel: bump 4.9 to 4.9.110
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-07-02 07:04:34 +02:00
Lucian Cristian
4ec9763ee9 firmware-utils: tplink-safeloader: switch tl-wr1043nd-v4 to dynamic partitions
Use the new dynamic partition split in tplink-safeloader so we no longer
have to worry about kernel size increases.

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-27 08:42:54 +02:00
Adrian Schmutzler
5c5bf8b865
ar71xx: Add support for TP-Link CPE210 v2
This PR adds support for a popular low-cost 2.4GHz N based AP

Specifications:
 - SoC: Qualcomm Atheros QCA9533 (650MHz)
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz N based built into SoC 2x2
 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Notes:
TP-Link does not use bootstrap registers so without this patch reference
clock detects as 40MHz while it is actually 25MHz.
This is due to messed up bootstrap resistor configuration on the PCB.
Provided GPL code just forces 25MHz reference clock.
That causes booting with completely wrong clocks, for example, CPU tries
to boot at 1040MHz while the stock is 650MHz.
So this PR depends on PR #672 to remove 40MHz reference clock.
Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-23 16:06:31 +02:00
Adrian Schmutzler
2524febf79
ar71xx: Add TP-Link Pharos v2 board detection
Add support for detecting TP-Link Pharos v2 boards.
They use different format in product-info partition than v1 boards.

Code was written mostly by Alexander Couzens <lynxis@fe80.eu>

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-23 16:02:01 +02:00
Arvid E. Picciani
bf39d5594b ar71xx: add support for TP-LINK Archer C7 v5
TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9563+QCA9880.

Specification:

- 750/400/250 MHz (CPU/DDR/AHB
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 10x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin
and rename it to ArcherC7v5_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Arvid E. Picciani <aep@exys.org>
2018-06-20 15:36:19 +02:00
David Ehrmann
81d446b045 ar71x: add support for Mikrotik Routerboard wAP R
This commit adds support for the Mikrotik wAP R (RBwAPR-2nD). The change
is based on 3b15eb0 which added support for the wAP 2nD. This change lacks
LED support.

Specifications:

- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9531, 802.11b/g/n 2x2:2
- Ethernet: 1x100Mbps
- Power: 9-30V Passive PoE, 9-30V DC jack, 9-30V automotive jack
- SIM card slot
- Mini-PCIe slot

Installation:

1. Login to the Mikrotik WebUI to backup your licence key
2. Change the following settings in System->Routerboard->Settings:
  - Boot device: try ethernet once then NAND
  - Boot protocol: DHCP
  - Force Backup Booter: checked
3. Setup a DHCP/BOOTP server with:
  - DHCP-Option 66 (TFTP server name) pointing to a local TFTP
    server within the same subnet of the DHCP range
  - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
    of the to be booted image, e.g.
    openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
4. Power off the device
5. If this is the second attempt to boot OpenWRT or the boot device isn't
   "try ethernet once then NAND," press and hold the reset button while
   powered off. If this is the first attempt, this step isn't necessary.
6. Power on the device, holding the reset button for 15-20s if already
   pressed from the previous step.

The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started OpenWRT via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install OpenWRT.

Revert to RouterOS

Use the "rbcfg" package on in OpenWRT:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply

Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.

Signed-off-by: David Ehrmann <ehrmann@gmail.com>
2018-06-19 14:32:47 +02:00
David Bauer
b4bf43c667 ar71xx: add support for Fritz!WLAN Repeater 450E
This commit adds support for the AVM Fritz!WLAN Repeater 450E

SOC:    Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4GHz WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - Most LEDs

Not working:
 - 2 RSSI LEDs
   AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they
   control over MDIO. Our driver doesn't expose these LEDs as GPIOs.
   While it is possible to implement this feature, it would require an
   additional kernel patch for a minor functionality.

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-18 23:23:30 +02:00
David Bauer
abb4ab076f ar71xx: fix incorrect speed setting on QCA9556
The QCA9556 only has a SGMII interface. However the speed on the
ethernet link is set for the non-existant xMII interface.

This commit fixes this behavior.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-18 23:23:30 +02:00
Thomas Nixon
bb71a3f27e ar71xx: add kmod-usb-ehci to fix USB on RB hAP AC
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
2018-06-18 18:21:20 +02:00
Kevin Darbyshire-Bryant
f60301db74 kernel: bump 4.9 to 4.9.107
Refresh patches.

Compile-tested for: ar71xx
Run-tested on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-09 22:39:17 +02:00
David Bauer
daeab36c1b ar71xx: use Power-LED as Diag-LED on FRITZBox 4020
This commit makes use of the Power-LED as Diag-LED, allowing the LED to
work as a status indicator.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-09 13:45:29 +02:00
David Bauer
9ec117c5be ar71xx: fix AVM package selection
The AVM package selection partially broke with the addition of the
FRITZ!Box 4020. This commit restores the intended behavior.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-09 13:45:29 +02:00
Sven Eckelmann
4f6320704f ar71xx: Fix offset to WMAC address for 8devices Lima
The ART partition of the Lima board stores exactly three mac addresses:

* 0x0: eth0
* 0x6: eth1
* 0x1002: wmac

The first two are correctly assigned in the mach file but the latter points
to 0x800. But this position is set to ff:ff:ff:ff:ff:ff. Luckily, the
driver falls back in ath9k_hw_init_macaddr to the EEPROM mac address when
it doesn't find a valid mac address in the platform_data.

Remove this bogus offset to the ART partition to directly load the wmac via
the EEPROM data in the ART partition.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2018-06-08 09:39:14 +02:00
Koen Vandeputte
55b4b1eba0 ar71xx: fix USB switch to mPCIE for Mikrotik rb91x boards
Some devices like the Mikrotik RB912 only have 1 USB port
which is shared between an USB A type port, and the mini PCIe socket.

Toggling a gpio selects the output to which USB is connected.

Since kernel 4.9, gpio base is rounded up to a value of 32.

Commit 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values") accounts correctly for that.
In this commit, rb912 sees it's value changed from AR934X_GPIO_COUNT (23) to 32
This means that the USB toggle gpio number actually also changes from 52 to 61.

But ..
Some of these GPIO numbers are also used in other locations, like the boardfile.
The author forgot to also change them over there.

Switching the USB port to mPCIe now shows my modem is correctly discovered again:

[ 2863.864471] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 2864.055303] usb 1-1: config 1 has an invalid interface number: 8 but max is 3
[ 2864.062728] usb 1-1: config 1 has no interface number 1
[ 2864.074567] qcserial 1-1:1.0: Qualcomm USB modem converter detected
[ 2864.081474] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB0
[ 2864.111960] qcserial 1-1:1.2: Qualcomm USB modem converter detected
[ 2864.118976] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB1
[ 2864.139808] qcserial 1-1:1.3: Qualcomm USB modem converter detected
[ 2864.146777] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB2
[ 2864.165276] qmi_wwan 1-1:1.8: cdc-wdm0: USB WDM device
[ 2864.171879] qmi_wwan 1-1:1.8 wwan0: register 'qmi_wwan' at usb-ehci-platform-1, WWAN/QMI device, 02:00:44:ed:3b:11

Fixes: 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: Robin Leblon <robin.leblon@ncentric.com>
Cc: Felix Fietkau <nbd@nbd.name>
2018-06-08 09:31:35 +02:00
David Bauer
e36f8b3f39 ar71xx: add support for OCEDO Koala
This commit adds support for the OCEDO Koala

SOC:	Qualcomm QCA9558 (Scorpion)
RAM:    128MB
FLASH:  16MiB
WLAN1:  QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2:  QCA9880 5 GHz 802.11nac 3x3
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-07 09:31:58 +02:00
Matthias Schiffer
0c0bb62999
ar71xx: switch CPE/WBS 210/510 to okli-loader
We recently increased the kernel partition size of the CPE/WBS 210/510.
This works fine for new installations of the factory image, but on
sysupgrades, the partition table read by the bootloader is not adjusted.
This limits the maximum size of the kernel loaded by the bootloader to the
old partition size.

While adjusting the partition table would be a cleanest solution, such a
migration would have to happen before an upgrade to a new version with a
newer kernel. This is error-prone and would require a two-step upgrade, as
we mark the partition table partition read-only.

Instead, switch from the lzma-loader with embedded kernel to the
okli-loader, so only the tiny lzma-loader is loaded by the bootloader as
"kernel", and the lzma-loader will then load the rest of the kernel by
itself.

Fixes: e39847ea2f ("ar71xx: increase kernel partition size for CPE/WBS 210/510")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:53 +02:00
Matthias Schiffer
108a6f6792
ar71xx: make loader-okli build step more generic
Add support for different loader types.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:53 +02:00
Matthias Schiffer
9968dcedb4
ar71xx: lzma-loader: constify kernel argv array
By making the kernel argv array const, the .data section can always be
omitted from the laoder binary.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:52 +02:00
Matthias Schiffer
8d851a95b7
ar71xx: lzma-loader: set page size to 4KB
The text section in the ELF loader is aligned to the maximum page size,
which defaults to 64KB. Reduce it to the actual page size to avoid wasting
flash space for this alignment.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:52 +02:00
Matthias Schiffer
a28e46b7cc
ar71xx: lzma-loader: move padding workaround to gzip step
Some devices (TP-Link TL-WR1043ND v1) don't boot reliably when the
uncompressed loader is too small. This was workarounded in the loader by
adding 512KB of padding to the .data section of the loader binary.

This approach had two issues:

- The padding was only working when .data was non-empty (otherwise the
  section would become NOBITS, omitting it in the binary). .data was only
  empty when no CMDLINE was set, leading to further workarounds like
  fe594bf90d ("ath79: fix loader-okli, lzma-loader"), and this
  workaround was only effective because a missing "const" led to the kernel
  argv being stored in .data instead of .rodata
- The padding was not only added to the compressed .gz loader, but also
  uncompressed .bin and .elf loaders. The prevented embedding the kernel
  cmdline in the loader for non-gz loader types.

To fix both issues, move the creation of the padding from the linker script
to the gzip step.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:52 +02:00
Kevin Darbyshire-Bryant
7dca1bae82 kernel: bump to 4.9.105
Refresh patches.

Drop patches that have been upstreamed:
target/linux/ar71xx/patches-4.9/106-01-MIPS-ath79-fix-AR724X_PLL_REG_PCIE_CONFIG-offset.patch
target/linux/generic/backport-4.9/095-v4.12-ipv6-Need-to-export-ipv6_push_frag_opts-for-tunnelin.patch
target/linux/generic/pending-4.9/180-net-phy-at803x-add-support-for-AT8032.patch
target/linux/generic/pending-4.9/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
target/linux/generic/pending-4.9/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch

Compile & run tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-01 08:25:14 +02:00
Luo chongjun
312d7a4a5a ar71xx: add support for GL.iNet GL-AR750S
This patch adds supports for GL-AR750S.

Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)

Flash instruction:
Apply factory image via web-gui.

Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
2018-05-27 09:26:09 +02:00
Jo-Philipp Wich
3b749d4acc ar71xx: fix bad "proto" references in default network configuration
This change was originally meant to go along with the ucidef_set_interface()
fixup.

Fixes: 7e664b7c2d ("base-files: fix ucidef_set_interface() protocol selection")
Fixes: 85048a9c1f ("base-files: rework _ucidef_set_interface to be more generic")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-25 09:46:55 +02:00
John Crispin
f7aa08595d kernel: add reset control support to rtl8366 driver
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-24 15:43:39 +02:00
Roman Yeryomin
85048a9c1f base-files: rework _ucidef_set_interface to be more generic
This is a rework of previously submitted patch reworking
ucidef_set_interface_raw [1]. Here, keep the idea but instead
make _ucidef_set_interface more generic and use it instead of
ucidef_set_interface_raw.
Also change the users like ucidef_set_interface_lan and others.

[1] https://patchwork.ozlabs.org/patch/844961/

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-24 09:39:47 +02:00
Chuanhong Guo
a789c0f491 ar71xx: Add support for PISEN TS-D084
PISEN TS-D084 is an wireless router with a battery and integrated power supply based on Atheros AR9331.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz (AR9331)
- 1x USB 2.0

Flash instruction:
The manufacturer are using exactly the same firmware header as TP-LINK TL-WR703N (including device ID!). Simply upload the factory firmware into WebUI and flashing is done.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-05-22 07:58:16 +02:00