I did not port the regulator and power patches from Stefan Wahren
because I talked to him and he told me that work on this is currently
stalled. And since AFAIK nothing depends on these patches, leaving them
out seems reasonable.
I build minimum default configurations and run-tested them on both
I2SE Duckbill devices and Olimex Olinuxino Maxi boards successfully [1].
[1] Tested:
- debug uart is working
- boot without any obvious kernel problem
- network is coming up and data transfer is possible
- Olinuxino: USB detects a plugged-in pen drive
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
[refreshed config and patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In preparation for bumping mxs target to 4.9, disable a bunch of configuration
symbols that provoked config prompts.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
- Refreshed all patches
- Adapted 1 (0031-mtd-add-SMEM-parser-for-QCOM-platforms.patch)
Compile tested on: brcm2708, cns3xxx, imx6
Run tested on: brcm2708, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Compile and run tested on brcm2708]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Use --mtime when SOURCE_DATE_EPOCH is set.
Use gzip -n9z instead of tar z to remove
timestamp in gzip header.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This patch fixes a problem where the AR8035 PHY can't be
detected on the Cisco Meraki MR24, when the ethernet cable
is not connected during boot.
Russell Senior reported:
|This appears to be a problem during probing of the AR8035
|phy chip. When ethernet has no link, the phy detection fails,
|and eth0 is not created. Plugging ethernet later has no effect,
|because there is no interface as far as the kernel is
|concerned. The relevant part of the boot log looks like this:
|
|[ 0.876611] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
|[ 0.882532] /plb/opb/ethernet@ef600c00: reset timeout
|[ 0.888546] /plb/opb/ethernet@ef600c00: can't find PHY!
(<https://bugs.lede-project.org/index.php?do=details&task_id=687>)
Fixes FS#687
Cc: Chris Blake <chrisrblake93@gmail.com>
Reported-by: Russell Senior <russell@personaltelco.net>
Fixes: 23fbb5a87c56e98 ("emac: Fix EMAC soft reset on 460EX/GT")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)
To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add upstream send AR724x PCIe patches to get the PCIe controller out of
reset during driver init.
The AVM Fritz 300E bootloader doesn't take care of releasing the
different PCIe controller related resets which causes an endless hang
as soon as either the PCIE Reset register (0x180f0018) or the PCI
Application Control register (0x180f0000) is read from.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The driver is used for boards outside the lantiq target as well. Move
it to generic to make it available for more targets.
The phy driver is included in kernel 4.8 as INTEL_XWAY_PHY.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Except for renames and line changes the only conflict was in
allocate_partition in handling MTD_WRITEABLE. Hopefully it was handled
correctly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This mtd_roundup_to_eb helper was introduced years ago in the commit
daec7ad768 ("kernel/3.10: add separate rootfs partition parser") and
it was probably supposed to simplify code a bit.
With the recent upstream commit 1eeef2d7483a7 ("mtd: handle partitioning
on devices with 0 erasesize") the logic in allocate_partition got
slightly more complex and we can't use this simple helper anymore as it
doesn't support MTD_NO_ERASE properly.
There also isn't any real gain from this helper, so it's probably easier
to just don't use it *or* work on upstreaming it to avoid maintenance
cost.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
On boards which don't have a distinct internet and dsl led, use the
shared LED to indicate the xdsl line state and any traffic that is
send/received via the netdev. This traffic doesn't necessarily need to
be internet traffic.
Rename the shared LED of existing configs to "dsl", to match the new
defaults. The configuration of the to be renamed LED is identical with
the new defaults.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Allows to use a single LED for line init status indication and to show
any rx/tx activity on a synchronized dsl line.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
As of now OTP is being correctly parsed and the driver requires to parse pre-caldata to follow corresponding routine.
Rename cal file into pre-calfile so the board initialized correctly with API 2 board data (board-2.bin).
Also remove the now unneeded for qca9984 board.bin symlink to 5GHz calfile.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
No longer rewrite opkg list output in package_list function, remove
the awk call in the pipe (which was intended for a single specific
use-case).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
commit 19ac879954 (imagebuilder: add package_list function) introduced
a new function 'package_list' to the imagebuilder Makefile.
Unfortunately the package list was poluted by stdout noise of the
Makefile itself as well as opkg. Redirect those outputs to stderr to
make sure that the package_list returned doesn't contain progress
info output but really only packages.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The imagebuilder can now list all available packages by using make
package_list. This is usefull for scripts to retrieve a list of all
packages with versions (and size)
Signed-off-by: Paul Spooren <paul@spooren.de>
[daniel@makrotopia.org: fixed commit message]
The Cisco ON100 device is a Kirkwood based router:
SoC: Marvell 88F6282 1600Mhz
SDRAM memory: 512MB DDR3 1333Mhz
Gigabit ethernet: 2x Marvell 88E1310 (over RGMII)
Flash memory: 512MB
2 bi-colour status LEDs (green/red)
1 Reset button
1 USB 2.0 port (on back)
1 SDIO slot (on back)
This commit adds a target profile of "Cisco Systems ON100" under the target
system "Marvell Kirkwood".
Flashing can be performed over tftp, once "dhcp" has been issued:
tftpboot ${loadaddr} lede-kirkwood-on100-squashfs-factory.bin
nand erase 0x0c0000 ${filesize}
nand write ${loadaddr} 0x0c0000 ${filesize}
Once flashed, set environment variables to boot:
setenv bootcmd nand read \${loadaddr} 0x0c0000 0x540000\; setenv bootargs
\; bootm
saveenv
Signed-off-by: Makoto Takeuchi <mak0@lxsys.co.uk>
Evaluation boards are left in component form to ease flashing
using vendor tooling and instructions. These boards also do
not include the EOF marker in the UBIFS as the bootloaders
are recent and easily upgradeable.
The end product boards use factory.bin images based on the
dts layout and include EOF markers as bootloader UBI support
is not determined.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
All TP-Link TL-WR710N versions share the same machine code.
This has been working since the beginning as we don't use double-quotes
to protect spaces inside command line values. Thus, kernel interprets
'board=TL-WR710N v2' as 'board=TL-WR710N' and separate parameter 'v2'.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Keep TP-Link devices definitions in alphabetical order whenever it's
possible. Also group together similar devices or devices from the same
series.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*
* Serial console is disabled in OEM non-beta firmwares and corresponding
GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
production (non-beta) U-Boot and firmware.
Currently not working:
1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
by some U-Boot versions.
Flash instruction under vendor GUI:
1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.
FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):
1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
turns on.
Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):
1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Use "GL.iNet" as vendor name (based on information from the vendor, this
is registered name of the company) and align model names with official
website.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Most of the custom Build/* functions in ar71xx target are rarely used by
image building code for devices from more than one subtarget. As they
don't need to be always included, move them to corresponding *.mk files.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ag71xx_ethtool_set_ringparam() will return an uninitialized value on
success.
Found-by: Coverity Scan #1330877
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Instead of bit banging SPI to talk to the GPIO chip, use the hardware
led controllers intended for controlling the LEDs.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fixes the following security vulnerabilities:
CVE-2017-8890
The inet_csk_clone_lock function in net/ipv4/inet_connection_sock.c in the
Linux kernel through 4.10.15 allows attackers to cause a denial of service
(double free) or possibly have unspecified other impact by leveraging use
of the accept system call.
CVE-2017-9074
The IPv6 fragmentation implementation in the Linux kernel through 4.11.1
does not consider that the nexthdr field may be associated with an invalid
option, which allows local users to cause a denial of service (out-of-bounds
read and BUG) or possibly have unspecified other impact via crafted socket
and send system calls.
CVE-2017-9075
The sctp_v6_create_accept_sk function in net/sctp/ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.
CVE-2017-9076
The dccp_v6_request_recv_sock function in net/dccp/ipv6.c in the Linux
kernel through 4.11.1 mishandles inheritance, which allows local users to
cause a denial of service or possibly have unspecified other impact via
crafted system calls, a related issue to CVE-2017-8890.
CVE-2017-9077
The tcp_v6_syn_recv_sock function in net/ipv6/tcp_ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.
CVE-2017-9242
The __ip6_append_data function in net/ipv6/ip6_output.c in the Linux kernel
through 4.11.3 is too late in checking whether an overwrite of an skb data
structure may occur, which allows local users to cause a denial of service
(system crash) via crafted system calls.
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-8890
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9074
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9075
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9076
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9077
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9242
Ref: https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.9.31
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fixes the following security vulnerabilities:
CVE-2017-8890
The inet_csk_clone_lock function in net/ipv4/inet_connection_sock.c in the
Linux kernel through 4.10.15 allows attackers to cause a denial of service
(double free) or possibly have unspecified other impact by leveraging use
of the accept system call.
CVE-2017-9074
The IPv6 fragmentation implementation in the Linux kernel through 4.11.1
does not consider that the nexthdr field may be associated with an invalid
option, which allows local users to cause a denial of service (out-of-bounds
read and BUG) or possibly have unspecified other impact via crafted socket
and send system calls.
CVE-2017-9075
The sctp_v6_create_accept_sk function in net/sctp/ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.
CVE-2017-9076
The dccp_v6_request_recv_sock function in net/dccp/ipv6.c in the Linux
kernel through 4.11.1 mishandles inheritance, which allows local users to
cause a denial of service or possibly have unspecified other impact via
crafted system calls, a related issue to CVE-2017-8890.
CVE-2017-9077
The tcp_v6_syn_recv_sock function in net/ipv6/tcp_ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.
CVE-2017-9242
The __ip6_append_data function in net/ipv6/ip6_output.c in the Linux kernel
through 4.11.3 is too late in checking whether an overwrite of an skb data
structure may occur, which allows local users to cause a denial of service
(system crash) via crafted system calls.
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-8890
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9074
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9075
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9076
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9077
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9242
Ref: https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.4.71
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last
one is disabled by default then disable CONFIG_SG_POOL by default too.
And explicitly enable it only for platforms that use CONFIG_SCSI.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Add HAVE_IRQ_EXIT_ON_IRQ_STACK kernel configuration symbol that was
missed during backporting separate IRQ stack for MIPS from upstream.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
PHY core treats any positive return value as the auto-negotiation done
indication. Since we do not actually check any device register in this
callback then update it to return positive value with a neutral meaning
instead of the register flag to avoid confusing for future readers.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
The Marvel 88E6060 switch has an MDIO interface, but does not emulate
regular PHY behavior for the host. The network core can not detect using
the generic code, whether the connection via the attached PHY can be
used or not. The PHY's state machine is stuck in a state of
auto-negotiation and does not go any further so the Ethernet interface
of the router stay forever in the not-runing state.
Fix this issue by implementing the aneg_done callback to be able to
inform the network core that the Ethernet interface link to which the
switch is connected can be marked as RUNNING.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Drop the own PHY polling function and switch to using the kernel PHY
state machine. This change allows driver to work correctly with devices
that do not support PHY behaviour but whose driver could emulate
autonegotiation completion (e.g. MV88E6060 and IP17xx switches).
NB: earlier this driver rely on flaws in PHY core code and could use PHY
device without really starting it. But now (at least in kernel 4.9)
this trick no more work and network interface could stuck in not-running
state.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Few tiny fixes for issues caused by changes in the upstream:
- do not touch PHY IRQ array (core code initializes it itself now)
- add missed SET_NETDEV_DEV() invocation (causes segfault during phy
connection)
- use phy API inside the MDIO probe function instead of direct field
access (consider phy structure changes in upstream and prevent
similar issues in the future)
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
This patch adds support for the Ubiquiti EdgeRouter X-SFP and
improves support for the EdgeRouter X (PoE-passthrough).
Specification:
- SoC: MediaTek MT7621AT
- Flash: 256 MiB
- RAM: 265 MiB
- Ethernet: 5 x LAN (1000 Mbps)
- UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1
- EdgeRouter X:
- 1 x PoE-Passtrough (Eth4)
- powered by Wallwart or passive PoE
- EdgeRouter X-SFP:
- 5 x PoE-Out (24V, passive)
- 1 x SFP (unknown status)
- powered by Wallwart (24V)
Doesn't work:
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
nand/spi drivers do not support pin sharing,
so it is not accessable and disabled. Stock
firmware could read it and it was empty.
Installation
via vendor firmware:
- build an Initrd-image (> 3MiB) and upload the factory-image
- initrd can have luci-mod-failsafe
- flash final firmware via LuCI / sysupgrade on rebooted system
via TFTP:
- stop uboot into tftp-load into option "1"
- upload factory.bin image
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
This change add IPQ40xx AP-DK04.1-C1 board image support,
enables ubi image for IPQ40xx AP-DK04.1-C1 board and also
add sysupgrage support for AP-DK04.1-C1 and generates a
sysupgrade.tar image.
Testing:
*Tested on IPQ40xx AP-DK04.1-C1:
a. NAND boot
b. ubi sysupgrade
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
x86 board.d only contains a case for the APU2, not the APU1. This
causes, for example, network configuration not to be created correctly.
Even though the APU1 seems to reaching EOL, there a still a lot of them
out there.
The APU1 and APU2 is configured in the same way and this patch should
also be considered for stable, as the error also exists there.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Now that we always provide these partitions through DT, we don't need to
pass their data through parser data from board files anymore.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Allow the parser to be invoked from DT without fixed cfe/linux/nvram
partitions. This allows flash to be probed from DT also for multi
flash-size images.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The patch 0008 removes the vanilla kernel gptu.c of lantiq.
But the replacement file timer.c does not work Amazon-SE and
is also protected therefore with an CONFIG_SOC_AMAZON_SE :-)
This commit will re-activate the default vanilla kernel code
in gptu.c for Amazon-SE.
Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
[refresh patches and add same change for kernel 4.9]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for the Allnet ADSL2+ Modem ALL0333CJ.
Specifications:
- SoC: Amazon-SE
- RAM: 16MB
- Storage: 4MB NOR FLash
- LEDs: Power, Ethernet, DSL (Sync)
- Buttons: 1x Reset Button (not currently supported, will be done)
- 1x Ethernet-Port: 1x RJ45 10/100BaseTX
- 1x WAN-Port: AnnexB & J, G.992.1(ADSL), G.992.3(ADSL2), G.992.5(ADSL2+)
Installation:
- can be done via telnet+tftp or serial console
- default passwords:
- via telnet (root:admin)
- via webinterface http://172.16.1.254:8235/ (admin:coolwhite)
Installation via telnet / tftp:
host: # your own host must have an tftpd daemon, then do this:
host: ifconfig eth0:172 172.16.1.1 up
host: # telnet to allnet modem, root:admin
host: telnet 172.16.1.254
modem: # kill this daemon, it spams your console
modem: killall dsl_cpe_control
modem: # change to some place in ram:
modem: cd /ramdisk/tftp_upload
modem: # load lede-lantiq-ase-ALL0333CJ-squashfs-sysupgrade.bin alias uImage
modem: tftp -g -r uImage 172.16.1.1
modem: # load these extra tools from your tftpd via:
modem: # source: https://github.com/mcmilk/uboot-utils/releases/download/0.1/mips32.tar.gz
modem: tftp -g -r flashwrite 172.16.1.1
modem: tftp -g -r fw_setenv 172.16.1.1
modem: tftp -g -r fw.conf 172.16.1.1
modem: ln -s fw_setenv fw_printenv
modem: chmod +x *
modem: ./fw_setenv disable_recovery y
modem: ./fw_setenv kernel_addr 0xb0010000
modem: ./flashwrite /dev/mtd/1 uImage 0
Installation via serial line at uboot:
uboot: # erase everything exept bootloader
uboot: protect on b0000000 +10000; protect on b03f0000 +10000
uboot: erase all
uboot: # get new firmware via tftp:
uboot: tftpboot 0x80100000 uImage; setenv kernel_addr 0xb0010000
uboot: # copy to flash:
uboot: cp.b 0x80100000 $(kernel_addr) $(filesize)
uboot: # disable proprietary image checking:
uboot: setenv disable_recovery=y; saveenv
uboot: # reboot with LEDE ;)
uboot: reset
Ethernet works as expected, DSL syncronization does not work properly
currently, I am working on this issue.
Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
Enable the building of Netgear DGN1000B images. I have an
example device here, but it was not tested currently.
Also WLAN and USB is not ready in the moment.
This is just the proper way, so that developing on this
device is known to be done in the near future.
Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
Add block device sd to kernel config otherwise AHCI/eSATA devices won't get enumerated in /dev
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Explicitely disable X2APIC support on legacy targets since the targeted
processor types do not support it anyway there.
Fixes FS#285.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
mvebu was modifying RAMFS_COPY_BIN and RAMFS_COPY_DATA from a
sysupgrade_pre_upgrade hook. As the ramfs is created from stage2, this
did not have an effect anymore after the staged sysupgrade changes.
As it doesn't really hurt to copy fw_printenv and fw_setenv
unconditionally, simply add them in /lib/upgrade/platform.sh, so stage2
will see them.
Config copying is moved to a function called by platform_copy_config, where
it belongs.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: FS#821
Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
If nand chip has no NAND_NO_SUBPAGE_WRITE flag on its options
ubifs can't use it mtd devices and the kernel crashes with error:
__nand_correct_data: uncorrectable ECC error
Signed-off-by: Sergey Sergeev <adron@yapic.net>
Fixes these prints on boot:
[ 13.785600] imx-uart 2020000.serial: DMA transaction error.
[ 13.793134] imx-uart 2020000.serial: DMA transaction error.
[ 13.798721] imx-uart 2020000.serial: DMA transaction error.
Based on following upstream patch by Tim Harvey (Gateworks):
80a01b6582
TX complete DMA messages are getting missed.
This is also currently an issue in mainline.
For now we will disable DMA in serial/imx.c.
This resolves an issue encountered with RS485 transmit.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The "reserved" partition should probably be read-only, just in case. Even
not knowing it's content, other devices have marked it as such, so it
seems a good idea to do so also for this device.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Mathias Kresin <dev@kresin.me>
CC: Hanqing Wong <hquu@outlook.com>
This fixes wrong GPIO numbers for LEDs and button in Wallys DR344 board
and sets color of all LEDs to green as the mass production boards have
only green one.
Actually, DR344 has 6 GPIO-connected LEDs and one button:
- GPIO11: status
- GPIO12: sig1
- GPIO13: sig2
- GPIO14: sig3
- GPIO15: sig4
- GPIO16: reset button
- GPIO17: lan
WAN LED is connected directly with AR8035 PHY.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This aligns default network interfaces configuration with vendor
firmware: GE (eth0) -> wan, FE (eth1) -> lan.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GMAC0 interface of AR9344 SOC in Wallys DR344 board is connected with
AR8035, not with AR8327. Without this fix, GE interface doesn't work at
all or shows high packet loss ratio.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.
The device is based on Qualcomm/Atheros AR9341 v1.
Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button
Flash instructions:
You have three options:
- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.
- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.
- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:
*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
stat -- Status
sys -- System
wless2 -- 2.4G-Wireless
mgmt -- Management
tree -- Tree
help -- Help
reboot -- Reboot
ens202ext>mgmt
Management
---========= Commands Help =========---
admin -- Administration
mvlan -- Management VLAN settings
snmp -- SNMP settings
backup -- Backup/Restore settings
autorb -- Auto reboot settings
fwgrade -- Firmware upgrade
time -- Time settings
wifisch -- Wifi schedule
log -- Log
diag -- Diagnostics
disc -- Device Discovery
logout -- Logout
help -- Help
exit -- Exit
ens202ext/mgmt>fwgrade
Management --> Firmware upgrade
---========= Commands Help =========---
fwup -- Firmware upgrade
help -- Help
exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin
Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
The single SFP port is meant for direct media access to WAN, such as
VDSL2, GPON). While it could also be used for in-home fiber, it is much
more likely that the LAN is standard ethernet, especially considering
that SFP is the onmly port that can go beyond 1Gbps.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Take explicit note of what physical ports eth{0,1,2} refer to.
Also repair port assignment:
At some point between 4.9.20 and 4.9.29 the numbering changed.
Keep previous port assignment that was:
LAN = SFP+Switch
WAN = standalone ethernet
Also use the same assignment for Clearfog-Base to avoid confusion.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Installing all armada-388-clearfog-* DTBs in the same sdcard image,
it now becomes much easier to swap sdcards between different device variants.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
U-Boot provides standard variables for load addresses, and
filesystem-agnostic load-commands. Furthermore thanks to distro-boot,
the device and partition from which the system boots is known.
The new boot-script makes use of all this information.
Tested on the only board that uses this boot-script: Clearfog Pro
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
sunxi sysupgrade was based on the x86 implementation; sync fixes and other
changes from the current x86 version:
x86: fix sysupgrades on disks with 4k block size
x86: sysupgrade: move partition table change check to platform_check_image
x86: sysupgrade: refactor platform_do_upgrade
x86: sysupgrade: explicitly rescan disk after writing partition table
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
When existing partitions are retained, the dd call writing the uboot image
in the space before the first partition was accidentally writing the whole
image, making the code for individual partitions redundant. Limit the copy
to 1016KiB (the first 8KiB are skipped, and the first partition starts at
1024KiB).
In addition, conv=notrunc is replaced with conv=fsync. It seems this was an
oversight, as notrunc doesn't make sense for block devices and all other dd
commands use conv=fsync.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This should ensure that the kernel partition can be mounted in
platform_copy_config when its size has changed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
By returning early when no upgrade device can be found and handling the
SAVE_PARTITIONS=0 case differently, we can get rid of two levels of if.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The staged sysupgrade will prevent us from using ask_bool in
platform_do_upgrade; therefore, the check is moved to platform_check_image.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
All targets with NAND support should gradually move their nand_do_upgrade
calls from platform_pre_upgrade to platform_do_upgrade.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This change adds QPIC BAM dma and NAND driver node's in IPQ4019
device tree, also enable this for AP-DK04.1 based boards.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
This change adds support for below:
- Bam transaction which will be used for any NAND request.
- Reset function for NAND BAM transaction
- Add support for additional CSRs.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
The existing qcom_nand driver supports ADM DMA which is mainly
required for ipq806x family based boards,
IPQ40xx based boards uses BAM DMA in NAND driver, so this patch
adds BAM DMA support with compatible string as qcom,ebi2-nandc-bam.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
GPIO_PULL bits configurations in TLMM_GPIO_CFG register
differs for IPQ40xx from rest of the other qcom SoC's.
This change add support to configure the msm_gpio_pull
bits for ipq40xx, It is required to fix the proper
configurations of gpio-pull bits for nand pins mux.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
The generic preinit code is now able to setup network and switch vlan settings
from the /etc/board.json file, therefor drop the target specific code.
Fixes FS#790.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.
Hardware Specification (v1.0 EU):
- SoC: QCA9531
- Flash: Winbond W25Q64FV (8MiB)
- RAM: EtronTech EM6AB160TSE-5G (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 2NIC (3x100M + 1x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 12V 1A
Signed-off-by: Filip Moc <lede@moc6.cz>
Neither the AsiaRF AWM002 or AWM003 actually has an LED on the module
board. The ld1 and ld2 do not represent actual LEDs. These pins might
connect to LEDS on an eval board or other carrier board, but that is
outside the scope of this device tree file.
Signed-off-by: Russell Senior <russell@personaltelco.net>
UML statically links against libutil, librt and libpthread. Some hosts do not
necessarily have these libraries installed and we should find out sooner than
later (during the final vmlinux linking stage) about that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The device tree is at /proc/device-tree/ without a base subdir.
Fixes: da472e5b30 ("treewide: access device tree from userspace via /proc/")
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds supports for the GL-inet GL-MT300N-V2.
Specification:
- SoC: MediaTek MT7628AN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR
- Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps)
- USB: 1 x USB 2.0 port
- Button: 1 x switch button, 1 x reset button
- LED: 3 x LEDS (system power led is not GPIO controller)
- UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND)
Installation through Luci:
- The original firmware is LEDE, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.
Installation through bootloader webserver:
- Plug power and hold reset button until red LED blink to bright.
- Install sysupgrade image using web interface on 192.168.1.1.
Signed-off-by: Kyson Lok <kysonlok@gmail.com>
[match maximum image size with firmware partition]
Signed-off-by: Mathias Kresin <dev@kresin.me>
