Commit graph

562 commits

Author SHA1 Message Date
Hauke Mehrtens
880be9ca2f brcm47xx: add detection for Phicomm M1
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 38009
2013-09-16 19:53:09 +00:00
Hauke Mehrtens
bc5b56f42b brcm47xx: detect Linksys E1200 V2
This adds detection for Linksys E1200 V2

Thank you Lightsword and Rafał.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 38006
2013-09-16 19:49:02 +00:00
Hauke Mehrtens
23c34e820c brcm47xx: mtd: bcm47xxpart: detect "factory" partition
A new type of partition with magic FCTY was found on Huawei E970:
46 43 54 59 4b 51 37 4e  41 42 31 38 41 32 39 30  |FCTYKQ7NAB18A290|

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 38005
2013-09-16 19:47:30 +00:00
Hauke Mehrtens
f687ab2101 brcm47xx: bgmac: implement unaligned addressing for DMA rings that support it
This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 38004
2013-09-16 19:46:34 +00:00
Hauke Mehrtens
86405f2c4c brcm47xx: add detection code for Huawei E970
This is based on a patch by Mathias Adam.

Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 38001
2013-09-15 17:00:45 +00:00
Gabor Juhos
554772a665 kernel: update 3.10 to 3.10.12
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38000
2013-09-15 16:00:41 +00:00
Hauke Mehrtens
57c6730ed6 brcm47xx: bgmac: allow bigger et_swtype nvram variable
Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. Now it should be
possible to read decimal and hex vars of max 8 bit.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37999
2013-09-15 15:50:41 +00:00
Hauke Mehrtens
2693eab7fd brcm47xx: mtd: bcm47xxpart: detect block aligned Squashfs partition
Most of the bcm47xx devices use TRX format for storing kernel and some
partition like Squashfs or JFFS2. This is pretty flexible solution, CFE
(the bootloader) just writes (and later boots) TRX at some hardcoded
place and paritions can vary in the size.

However some devices don't use TRX format. Very recently we have
discovered ZTE H218N that has kernel and rootfs partitions at some
"random" places.

This patch allows Linux find a rootfs partition after installing custom
image with a CFE bootloader.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 37998
2013-09-15 15:47:45 +00:00
Hauke Mehrtens
bd6d4c4ded brcm47xx: update board detection patch
* Use different structs depending on the number of nvram variables to check.
* Add detection of ZTE H218N, this closes #14151.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37996
2013-09-15 15:08:29 +00:00
Hauke Mehrtens
c9399a1c81 brcm47xx: bgmac: fix internal switch initialization
Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.

Use correct bit for switch initialization and fix typo in the define.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 37993
2013-09-15 09:39:19 +00:00
Hauke Mehrtens
1268e064aa brcm47xx: detect Asus RT-N10
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37989
2013-09-14 16:19:21 +00:00
Hauke Mehrtens
3b3d4b6208 brcm47xx: tg3: use the phy address from et0phyaddr and not the default phy address.
Thank you Devastator for testing.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37986
2013-09-14 16:10:37 +00:00
Hauke Mehrtens
b73b915c54 brcm47xx: board detection, GPIO for Linksys E1000 V2.1
This patch adds board detection for the Linksys E1000 V2.1 router, as well
as GPIO support for same.

This fixes bug #14135. Currently, wired networking isn't working on the
router, and I haven't tried the wireless, but with this patch, OpenWRT
successfully boots, and all the LEDs and buttons work properly.

Signed-off-by: Zachary Catlin <zcatlin@indiana.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37977
2013-09-13 19:24:08 +00:00
Hauke Mehrtens
9141ab0ede brcm47xx: detect WRT310NV1
Thanks Devastator for testing

SVN-Revision: 37969
2013-09-13 15:56:35 +00:00
Hauke Mehrtens
0a0257d70e brcm47xx: remove support for kernel 3.8
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37959
2013-09-12 22:07:12 +00:00
Hauke Mehrtens
b4880b34ef brcm47xx: add default config for new kernel config option
SVN-Revision: 37958
2013-09-12 22:04:55 +00:00
Hauke Mehrtens
614e8f44bd kernel: update bcma and ssb to wireless-testing master-2013-09-09
SVN-Revision: 37957
2013-09-12 22:03:45 +00:00
Hauke Mehrtens
f181b07af8 brcm47xx: add me as maintainer
SVN-Revision: 37916
2013-09-07 15:46:27 +00:00
Gabor Juhos
d120ec18b2 kernel: update 3.10 to 3.10.10
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37890
2013-09-02 19:12:54 +00:00
Gabor Juhos
043edd8074 kernel: update 3.10 to 3.10.9
Also refresh 3.10 patches.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37832
2013-08-23 17:31:04 +00:00
Hauke Mehrtens
af161b6576 brcm47xx: fix typo in Broadcom-bgmac-b43 profile name
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37803
2013-08-17 13:41:22 +00:00
Hauke Mehrtens
2fcaba306e brcm47xx: change board detection for some Asus devices
This closes #13316

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37680
2013-08-04 12:36:13 +00:00
Hauke Mehrtens
290dade033 brcm47xx: switch to kernel 3.10.4
This uses a new switch driver.
The old ADMTEK Adm6996 switch is not supported any more.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37650
2013-08-01 21:01:59 +00:00
Hauke Mehrtens
7e14fd55fd brcm47xx: use lib phy when tg3 is in use
This is untested, but probably needed to make it work with the phy lib switch driver.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37649
2013-08-01 20:47:55 +00:00
Hauke Mehrtens
2b55968f5d brcm47xx: improve detection of Linksys WRTSL54GS
This closes #13319

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37647
2013-08-01 19:33:59 +00:00
Hauke Mehrtens
6d7f796b52 brcm47xx: remove support for kernel 3.9
This is not needed any more.

SVN-Revision: 37646
2013-08-01 19:17:51 +00:00
Hauke Mehrtens
2363cb3893 brcm47xx: add function to get a gpio pin by name
bcm47xx_nvram_gpio_pin() returns a gpio pin number for a given name based
on configuration data in nvram.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37644
2013-08-01 19:04:12 +00:00
Hauke Mehrtens
e2b2e3886b brcm47xx: run mtd fixtrx linux every time
With this patch it is possible to boot a device with kernel 3.10 a second time.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37625
2013-07-31 17:41:52 +00:00
Gabor Juhos
ef944dcb85 kernel: update 3.10 to 3.10.2
Also refresh 3.10 patches.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37502
2013-07-22 15:31:13 +00:00
Jonas Gorski
b1b4e7db13 kernel: move CONFIG_NET_IP_TUNNEL to generic
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 37465
2013-07-19 22:58:01 +00:00
Hauke Mehrtens
c7f8cb3f4f kernel: update bcma and ssb to version from wireless-testing/master tag master-2013-07-18
This should fix some build problems in b43 with kernel 3.3.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37432
2013-07-19 12:02:34 +00:00
Hauke Mehrtens
866e229299 brcm47xx: fix name of patch
SVN-Revision: 37340
2013-07-15 11:42:54 +00:00
Hauke Mehrtens
f8d55e7541 brcm47xx: use b53 phy driver for the switch in kernel 3.10
This makes it possible to use swconfig to controll the switch.

This was tested with devices using b43 and bgmac.
This was not tested on devices using tg3.
This does not support the adm switch used in some very old devices.

SVN-Revision: 37304
2013-07-14 14:11:17 +00:00
Hauke Mehrtens
a5c0ad6354 brcm47xx: add initial support for kernel 3.10
SVN-Revision: 37287
2013-07-14 13:44:45 +00:00
Hauke Mehrtens
3bc90a4d23 brcm47xx: fix switch handling
This fixes some problems with the switch handling

 * It now send the messages again to indicate a button for failsafe mode should be pressed
 * it does not leak packages between wan and lan any more
 * the switch works again in normal mode

The Ethernet connection has to be up when the switch driver switch-robo
is insmoded therefor we just do it again.
Explicitly set enable_vlan to prevent leaking packages.

This should close #13869, #13868 and #13716

SVN-Revision: 37286
2013-07-14 13:19:58 +00:00
Hauke Mehrtens
ef0b9be95e brcm47xx: do not load the kernel modules needed for Ethernet manually
add the boot flag to make the kernel modules needed for Ethernet and
diag load on startup.

SVN-Revision: 37284
2013-07-14 12:59:00 +00:00
Hauke Mehrtens
e800436de3 brcm47xx: do not change nvram without user interaction
SVN-Revision: 37281
2013-07-14 12:56:42 +00:00
Hauke Mehrtens
e041d370a7 brcm47xx: proc gets mounted without this patch
SVN-Revision: 37272
2013-07-13 21:42:19 +00:00
Hauke Mehrtens
8dabd7a26b brcm47xx: remove obsolete hotplug stuff
SVN-Revision: 37271
2013-07-13 20:38:33 +00:00
John Crispin
541bede918 brcm47xx: fix module insert order
https://dev.openwrt.org/ticket/13811

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 37161
2013-07-04 13:31:13 +00:00
Florian Fainelli
6a4f2922f6 targets: prepare for supporting normal and initramfs images
In order to support both normal images and initramfs, ensure that each
target sets KERNELNAME properly so that the generic kernel building code
can copy the corresponding files over $(KDIR) with the appropriate
extension. Update the various paths to the kernel and wrapper images
from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo).

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 37049
2013-06-27 19:58:31 +00:00
John Crispin
39df8d1a45 brcm47xx: dont manually insmod switch drivers
Signed-off-by: John Crispin <bloic@openwrt.org>

SVN-Revision: 36993
2013-06-21 16:53:15 +00:00
Hauke Mehrtens
9492d445de brcm47xx: run make kernel_oldconfig for 3.9 kernel config
SVN-Revision: 36928
2013-06-12 14:51:50 +00:00
Hauke Mehrtens
87f994d16d brcm47xx: remove support for kernel 3.6
SVN-Revision: 36927
2013-06-12 14:48:45 +00:00
Hauke Mehrtens
990423f3ef brcm47xx: add initial support for kernel 3.9
SVN-Revision: 36926
2013-06-12 14:47:53 +00:00
Gabor Juhos
46225b99d9 kernel: update linux 3.8 to 3.8.13
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36724
2013-05-26 16:02:31 +00:00
Jonas Gorski
526aedb705 kernel: move CONFIG_MIPS_SEAD3 to generic
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 36617
2013-05-12 21:41:55 +00:00
Gabor Juhos
e57c7d6c12 kernel: update linux 3.8 to 3.8.12
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36576
2013-05-08 08:53:53 +00:00
Gabor Juhos
8a9fe26f20 kernel: update linux 3.8 to 3.8.11
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36507
2013-05-01 22:15:18 +00:00
Hauke Mehrtens
ca7f9638d5 broadcom-diag: support for the WNDR3700v3
I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it
was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and
LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the
bootloader and stock firmware will accept.

The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving
its LEDs through an HC164 8-bit shift register.

Signed-off-by: Owen Kirby <osk@exegin.com>

SVN-Revision: 36482
2013-04-28 21:11:17 +00:00