ar71xx: add support for the MikroTik RB911-2Hn/5Hn boards

The patch adds support for the MikroTik RB911-2Hn (911 Lite2)
and the RB911-5Hn (911 Lite5) boards:

  https://mikrotik.com/product/RB911-2Hn
  https://mikrotik.com/product/RB911-5Hn

The two boards are using the same hardware design, the only difference
between the two is the supported wireless band.

Specifications:
  * SoC: Atheros AR9344 (600MHz)
  * RAM: 64MiB
  * Storage: 16 MiB SPI NOR flash
  * Ethernet: 1x100M (Passive PoE in)
  * Wireless: AR9344 built-in wireless MAC, single chain
              802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn)

Notes:
  * Older versions of these boards might be equipped with a NAND
    flash chip instead of the SPI NOR device. Those boards are not
    supported (yet).
  * The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the
    same hardware. Support for that can be added later with little
    effort probably.

Installation:

1. Setup a DHCP/BOOTP Server with the following parameters:
   * DHCP-Option 66 (TFTP server name): pointing to a local TFTP
     server within the same subnet of the DHCP range
   * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
     of the to be booted image. The usable intramfs files are:
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
       - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin

2. Press the reset button on the board and keep that pressed.

3. Connect the board to your local network via its ethernet port.

4. Release the button after the LEDs on the board are turned off.
   Now the board should load and start the initramfs image from
   the TFTP server.

5. Upload the sysupgrade image to the board with scp:
     $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin

5. Log in to the running system listening on 192.168.1.1 via ssh
   as root (without password):
     $ ssh root@192.168.1.1

7. Flash the uploaded firmware file from the ssh session via the
   sysupgrade command:
     root@OpenWrt:~# sysupgrade /tmp/fw.bin

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
This commit is contained in:
Gabor Juhos 2018-01-18 13:50:32 +01:00 committed by John Crispin
parent a4320b3332
commit eb9e3651dd
11 changed files with 123 additions and 3 deletions

View file

@ -292,6 +292,10 @@ rb-750up-r2)
ucidef_set_led_switch "port4" "port3" "rb:green:port4" "switch0" "0x04"
ucidef_set_led_switch "port5" "port5" "rb:green:port5" "switch0" "0x02"
;;
rb-911-2hn|\
rb-911-5hn)
ucidef_set_led_netdev "eth" "ETH" "rb:green:eth" "eth0"
;;
rb-941-2nd)
ucidef_set_led_timer "user" "USR/ACT" "rb:green:user" "1000" "1000"
;;

View file

@ -93,6 +93,8 @@ ar71xx_setup_interfaces()
pqi-air-pen|\
rb-411|\
rb-411u|\
rb-911-2hn|\
rb-911-5hn|\
rb-911g-2hpnd|\
rb-911g-5hpacd|\
rb-911g-5hpnd|\

View file

@ -319,6 +319,8 @@ get_status_led() {
rb-750-r2|\
rb-750p-pbr2|\
rb-750up-r2|\
rb-911-2hn|\
rb-911-5hn|\
rb-911g-2hpnd|\
rb-911g-5hpacd|\
rb-911g-5hpnd|\

View file

@ -941,6 +941,12 @@ ar71xx_board_detect() {
*"RouterBOARD 751G")
name="rb-751g"
;;
*"RouterBOARD 911-2Hn")
name="rb-911-2hn"
;;
*"RouterBOARD 911-5Hn")
name="rb-911-5hn"
;;
*"RouterBOARD 911G-2HPnD")
name="rb-911g-2hpnd"
;;

View file

@ -660,6 +660,8 @@ platform_check_image() {
rb-750-r2|\
rb-750p-pbr2|\
rb-750up-r2|\
rb-911-2hn|\
rb-911-5hn|\
rb-941-2nd|\
rb-951ui-2nd|\
rb-952ui-5ac2nd|\
@ -723,6 +725,8 @@ platform_pre_upgrade() {
rb-750-r2|\
rb-750p-pbr2|\
rb-750up-r2|\
rb-911-2hn|\
rb-911-5hn|\
rb-941-2nd|\
rb-951ui-2nd|\
rb-952ui-5ac2nd|\

View file

@ -1054,6 +1054,8 @@ config ATH79_MACH_RBSPI
select ATH79_ROUTERBOOT
help
Say 'Y' here if you want your kernel to support the
MikroTik ROuterBOARD 911-2Hn (911 Lite2)
MikroTik ROuterBOARD 911-5Hn (911 Lite5)
MikroTik RouterBOARD mAP
MikroTik RouterBOARD mAP lite
MikroTik RouterBOARD hAP lite

View file

@ -3,6 +3,8 @@
*
* - MikroTik RouterBOARD mAP 2nD
* - MikroTik RouterBOARD mAP L-2nD
* - MikroTik RouterBOARD 911-2Hn (911 Lite2)
* - MikroTik RouterBOARD 911-5Hn (911 Lite5)
* - MikroTik RouterBOARD 941L-2nD
* - MikroTik RouterBOARD 951Ui-2nD
* - MikroTik RouterBOARD 952Ui-5ac2nD
@ -509,6 +511,56 @@ static struct platform_device rbwapgsc_phy_device = {
},
};
/* RB911L GPIOs */
#define RB911L_GPIO_BTN_RESET 15
#define RB911L_GPIO_LED_1 13
#define RB911L_GPIO_LED_2 12
#define RB911L_GPIO_LED_3 4
#define RB911L_GPIO_LED_4 21
#define RB911L_GPIO_LED_5 18
#define RB911L_GPIO_LED_ETH 20
#define RB911L_GPIO_LED_POWER 11
#define RB911L_GPIO_LED_USER 3
#define RB911L_GPIO_PIN_HOLE 14 /* for reference */
static struct gpio_led rb911l_leds[] __initdata = {
{
.name = "rb:green:eth",
.gpio = RB911L_GPIO_LED_ETH,
.active_low = 1,
}, {
.name = "rb:green:led1",
.gpio = RB911L_GPIO_LED_1,
.active_low = 1,
}, {
.name = "rb:green:led2",
.gpio = RB911L_GPIO_LED_2,
.active_low = 1,
}, {
.name = "rb:green:led3",
.gpio = RB911L_GPIO_LED_3,
.active_low = 1,
}, {
.name = "rb:green:led4",
.gpio = RB911L_GPIO_LED_4,
.active_low = 1,
}, {
.name = "rb:green:led5",
.gpio = RB911L_GPIO_LED_5,
.active_low = 1,
}, {
.name = "rb:green:power",
.gpio = RB911L_GPIO_LED_POWER,
.default_state = LEDS_GPIO_DEFSTATE_ON,
.open_drain = 1,
}, {
.name = "rb:green:user",
.gpio = RB911L_GPIO_LED_USER,
.active_low = 1,
.open_drain = 1,
},
};
static struct gen_74x164_chip_platform_data rbspi_ssr_data = {
.base = RBSPI_SSR_GPIO_BASE,
.num_registers = 1,
@ -1015,8 +1067,53 @@ static void __init rbwapgsc_setup(void)
rbwapgsc_leds);
}
/*
* Setup the 911L hardware (AR9344).
*/
static void __init rb911l_setup(void)
{
const struct rb_info *info;
info = rbspi_platform_setup();
if (!info)
return;
if (!rb_has_hw_option(info, RB_HW_OPT_NO_NAND)) {
/*
* Old hardware revisions might be equipped with a NAND flash
* chip instead of the 16MiB SPI NOR device. Those boards are
* not supported at the moment, so throw a warning and skip
* the peripheral setup to avoid messing up the data in the
* flash chip.
*/
WARN(1, "The NAND flash on this board is not supported.\n");
} else {
rbspi_peripherals_setup(0);
}
ath79_register_mdio(1, 0x0);
ath79_init_mac(ath79_eth1_data.mac_addr, ath79_mac_base, 0);
ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
ath79_eth1_data.speed = SPEED_1000;
ath79_eth1_data.duplex = DUPLEX_FULL;
ath79_register_eth(1);
rbspi_wlan_init(0, 1);
rbspi_register_reset_button(RB911L_GPIO_BTN_RESET);
/* Make the eth LED controllable by software. */
ath79_gpio_output_select(RB911L_GPIO_LED_ETH, AR934X_GPIO_OUT_GPIO);
ath79_register_leds_gpio(-1, ARRAY_SIZE(rb911l_leds), rb911l_leds);
}
MIPS_MACHINE_NONAME(ATH79_MACH_RB_MAPL, "map-hb", rbmapl_setup);
MIPS_MACHINE_NONAME(ATH79_MACH_RB_941, "H951L", rbhapl_setup);
MIPS_MACHINE_NONAME(ATH79_MACH_RB_911L, "911L", rb911l_setup);
MIPS_MACHINE_NONAME(ATH79_MACH_RB_952, "952-hb", rb952_setup);
MIPS_MACHINE_NONAME(ATH79_MACH_RB_962, "962", rb962_setup);
MIPS_MACHINE_NONAME(ATH79_MACH_RB_750UPR2, "750-hb", rb750upr2_setup);

View file

@ -190,6 +190,7 @@ enum ath79_mach_type {
ATH79_MACH_RB_750UPR2, /* MikroTik RouterBOARD 750UP r2 */
ATH79_MACH_RB_751, /* MikroTik RouterBOARD 751 */
ATH79_MACH_RB_751G, /* Mikrotik RouterBOARD 751G */
ATH79_MACH_RB_911L, /* Mikrotik RouterBOARD 911-2Hn/911-5Hn boards */
ATH79_MACH_RB_922GS, /* Mikrotik RouterBOARD 911/922GS boards */
ATH79_MACH_RB_941, /* MikroTik RouterBOARD 941-2nD */
ATH79_MACH_RB_951G, /* Mikrotik RouterBOARD 951G */

View file

@ -40,7 +40,7 @@ define Device/rb-nor-flash-16M
LOADER_TYPE := elf
KERNEL_INSTALL := 1
KERNEL := kernel-bin | lzma | loader-kernel
SUPPORTED_DEVICES := rb-750-r2 rb-750up-r2 rb-750p-pbr2 rb-941-2nd rb-951ui-2nd rb-952ui-5ac2nd rb-962uigs-5hact2hnt rb-lhg-5nd rb-map-2nd rb-mapl-2nd rb-wap-2nd
SUPPORTED_DEVICES := rb-750-r2 rb-750up-r2 rb-750p-pbr2 rb-911-2hn rb-911-5hn rb-941-2nd rb-951ui-2nd rb-952ui-5ac2nd rb-962uigs-5hact2hnt rb-lhg-5nd rb-map-2nd rb-mapl-2nd rb-wap-2nd
IMAGE/sysupgrade.bin := append-kernel | kernel2minor -s 1024 -e | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
endef

View file

@ -1,6 +1,6 @@
--- a/arch/mips/ath79/prom.c
+++ b/arch/mips/ath79/prom.c
@@ -136,6 +136,30 @@ void __init prom_init(void)
@@ -136,6 +136,31 @@ void __init prom_init(void)
initrd_end = initrd_start + fw_getenvl("initrd_size");
}
#endif
@ -26,6 +26,7 @@
+ strstr(arcs_cmdline, "board=2011L") ||
+ strstr(arcs_cmdline, "board=2011r") ||
+ strstr(arcs_cmdline, "board=711Gr100") ||
+ strstr(arcs_cmdline, "board=911L") ||
+ strstr(arcs_cmdline, "board=922gs"))
+ ath79_prom_append_cmdline("console", "ttyS0,115200");
}

View file

@ -1,6 +1,6 @@
--- a/arch/mips/ath79/prom.c
+++ b/arch/mips/ath79/prom.c
@@ -136,6 +136,30 @@ void __init prom_init(void)
@@ -136,6 +136,31 @@ void __init prom_init(void)
initrd_end = initrd_start + fw_getenvl("initrd_size");
}
#endif
@ -26,6 +26,7 @@
+ strstr(arcs_cmdline, "board=2011L") ||
+ strstr(arcs_cmdline, "board=2011r") ||
+ strstr(arcs_cmdline, "board=711Gr100") ||
+ strstr(arcs_cmdline, "board=911L") ||
+ strstr(arcs_cmdline, "board=922gs"))
+ ath79_prom_append_cmdline("console", "ttyS0,115200");
}