ar71xx: Compex WPJ563 support

Specification:
- SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc)
- RAM: 128 MiB
- Storage: 16MB NOR flash
- Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO
- Ethernet: 2x1G

Tested and working:
- ethernet / switch / lan / wan
- 2.4GHz SoC wifi
- PCIe
- leds
- buzzer

Ramload:
- tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin
- bootm 0x84000000

Install:
- tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin
- erase 0x9f030000 +$filesize
- erase 0x9f680000 +1
- cp.b $fileaddr 0x9f030000 $filesize

Erasing 0x9f680000 is required because uboot defines
"bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot
the higher address. I think the 16 mb flash are intended to be used as
8+8mb for a fallback image. In my hardware only the lower address has a
bootable image. But to make sure future hardware will boot lede too, I
erase one block, so uboot will skip this address.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
This commit is contained in:
Christian Mehlis 2017-02-26 12:25:57 +01:00 committed by John Crispin
parent 967b6be118
commit dc4eae7a8c
12 changed files with 186 additions and 0 deletions

View file

@ -466,6 +466,10 @@ ar71xx_setup_interfaces()
ucidef_add_switch "switch0" \ ucidef_add_switch "switch0" \
"5:lan" "1:wan" "6@eth0" "5:lan" "1:wan" "6@eth0"
;; ;;
wpj563)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:wan"
;;
wrt160nl) wrt160nl)
ucidef_set_interfaces_lan_wan "eth0.1" "eth1" ucidef_set_interfaces_lan_wan "eth0.1" "eth1"
ucidef_add_switch "switch0" \ ucidef_add_switch "switch0" \

View file

@ -469,6 +469,9 @@ get_status_led() {
wpj558) wpj558)
status_led="$board:green:sig3" status_led="$board:green:sig3"
;; ;;
wpj563)
status_led="$board:green:sig1"
;;
wrt400n|\ wrt400n|\
wrt160nl) wrt160nl)
status_led="$board:blue:wps" status_led="$board:blue:wps"

View file

@ -1240,6 +1240,9 @@ ar71xx_board_detect() {
*"WPJ558") *"WPJ558")
name="wpj558" name="wpj558"
;; ;;
*"WPJ563")
name="wpj563"
;;
*"WPN824N") *"WPN824N")
name="wpn824n" name="wpn824n"
;; ;;

View file

@ -283,6 +283,7 @@ platform_check_image() {
wpj342|\ wpj342|\
wpj344|\ wpj344|\
wpj531|\ wpj531|\
wpj563|\
wrt400n|\ wrt400n|\
wrtnode2q|\ wrtnode2q|\
wzr-450hp2|\ wzr-450hp2|\

View file

@ -226,6 +226,7 @@ CONFIG_ATH79_MACH_WPJ342=y
CONFIG_ATH79_MACH_WPJ344=y CONFIG_ATH79_MACH_WPJ344=y
CONFIG_ATH79_MACH_WPJ531=y CONFIG_ATH79_MACH_WPJ531=y
CONFIG_ATH79_MACH_WPJ558=y CONFIG_ATH79_MACH_WPJ558=y
CONFIG_ATH79_MACH_WPJ563=y
CONFIG_ATH79_MACH_WRT160NL=y CONFIG_ATH79_MACH_WRT160NL=y
CONFIG_ATH79_MACH_WRT400N=y CONFIG_ATH79_MACH_WRT400N=y
CONFIG_ATH79_MACH_WRTNODE2Q=y CONFIG_ATH79_MACH_WRTNODE2Q=y

View file

@ -459,6 +459,17 @@ config ATH79_MACH_WPJ558
select ATH79_DEV_USB select ATH79_DEV_USB
select ATH79_DEV_WMAC select ATH79_DEV_WMAC
config ATH79_MACH_WPJ563
bool "Compex WPJ563 board support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_XD3200 config ATH79_MACH_XD3200
bool "YunCore XD3200 support" bool "YunCore XD3200 support"
select SOC_QCA956X select SOC_QCA956X

View file

@ -231,6 +231,7 @@ obj-$(CONFIG_ATH79_MACH_WPJ342) += mach-wpj342.o
obj-$(CONFIG_ATH79_MACH_WPJ344) += mach-wpj344.o obj-$(CONFIG_ATH79_MACH_WPJ344) += mach-wpj344.o
obj-$(CONFIG_ATH79_MACH_WPJ531) += mach-wpj531.o obj-$(CONFIG_ATH79_MACH_WPJ531) += mach-wpj531.o
obj-$(CONFIG_ATH79_MACH_WPJ558) += mach-wpj558.o obj-$(CONFIG_ATH79_MACH_WPJ558) += mach-wpj558.o
obj-$(CONFIG_ATH79_MACH_WPJ563) += mach-wpj563.o
obj-$(CONFIG_ATH79_MACH_WRT160NL) += mach-wrt160nl.o obj-$(CONFIG_ATH79_MACH_WRT160NL) += mach-wrt160nl.o
obj-$(CONFIG_ATH79_MACH_WRT400N) += mach-wrt400n.o obj-$(CONFIG_ATH79_MACH_WRT400N) += mach-wrt400n.o
obj-$(CONFIG_ATH79_MACH_WRTNODE2Q) += mach-wrtnode2q.o obj-$(CONFIG_ATH79_MACH_WRTNODE2Q) += mach-wrtnode2q.o

View file

@ -0,0 +1,150 @@
/*
* Compex WPJ563 board support
*
* Copyright (c) 2015 Qualcomm Atheros
* Copyright (c) 2012 Gabor Juhos <juhosg@openwrt.org>
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*
*/
#include <linux/platform_device.h>
#include <linux/ath9k_platform.h>
#include <linux/ar8216_platform.h>
#include <asm/mach-ath79/ar71xx_regs.h>
#include "common.h"
#include "dev-m25p80.h"
#include "machtypes.h"
#include "pci.h"
#include "dev-eth.h"
#include "dev-gpio-buttons.h"
#include "dev-leds-gpio.h"
#include "dev-spi.h"
#include "dev-usb.h"
#include "dev-wmac.h"
#define WPJ563_GPIO_LED_SIG1 1
#define WPJ563_GPIO_LED_SIG2 5
#define WPJ563_GPIO_LED_SIG3 6
#define WPJ563_GPIO_LED_SIG4 7
#define WPJ563_GPIO_BUZZER 19
#define WPJ563_GPIO_BTN_RESET 2
#define WPJ563_KEYS_POLL_INTERVAL 20 /* msecs */
#define WPJ563_KEYS_DEBOUNCE_INTERVAL (3 * WPJ563_KEYS_POLL_INTERVAL)
#define WPJ563_MAC0_OFFSET 0x10
#define WPJ563_MAC1_OFFSET 0x18
#define WPJ563_WMAC_CALDATA_OFFSET 0x1000
static struct gpio_led WPJ563_leds_gpio[] __initdata = {
{
.name = "wpj563:green:sig1",
.gpio = WPJ563_GPIO_LED_SIG1,
.active_low = 1,
},
{
.name = "wpj563:green:sig2",
.gpio = WPJ563_GPIO_LED_SIG2,
.active_low = 1,
},
{
.name = "wpj563:green:sig3",
.gpio = WPJ563_GPIO_LED_SIG3,
.active_low = 1,
},
{
.name = "wpj563:green:sig4",
.gpio = WPJ563_GPIO_LED_SIG4,
.active_low = 1,
},
{
.name = "wpj563:buzzer",
.gpio = WPJ563_GPIO_BUZZER,
.active_low = 0,
}
};
static struct gpio_keys_button WPJ563_gpio_keys[] __initdata = {
{
.desc = "Reset button",
.type = EV_KEY,
.code = KEY_RESTART,
.debounce_interval = WPJ563_KEYS_DEBOUNCE_INTERVAL,
.gpio = WPJ563_GPIO_BTN_RESET,
.active_low = 1,
},
};
static struct ar8327_pad_cfg WPJ563_ar8337_pad0_cfg = {
.mode = AR8327_PAD_MAC_SGMII,
.sgmii_delay_en = true,
};
static struct ar8327_platform_data WPJ563_ar8337_data = {
.pad0_cfg = &WPJ563_ar8337_pad0_cfg,
.port0_cfg = {
.force_link = 1,
.speed = AR8327_PORT_SPEED_1000,
.duplex = 1,
.txpause = 1,
.rxpause = 1,
},
};
static struct mdio_board_info WPJ563_mdio0_info[] = {
{
.bus_id = "ag71xx-mdio.0",
.phy_addr = 0,
.platform_data = &WPJ563_ar8337_data,
},
};
static void __init WPJ563_setup(void)
{
u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
u8 *mac = (u8 *) KSEG1ADDR(0x1f02e000);
ath79_register_m25p80(NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(WPJ563_leds_gpio),
WPJ563_leds_gpio);
ath79_register_gpio_keys_polled(-1, WPJ563_KEYS_POLL_INTERVAL,
ARRAY_SIZE(WPJ563_gpio_keys),
WPJ563_gpio_keys);
ath79_register_usb();
ath79_register_wmac(art + WPJ563_WMAC_CALDATA_OFFSET, NULL);
ath79_register_pci();
mdiobus_register_board_info(WPJ563_mdio0_info,
ARRAY_SIZE(WPJ563_mdio0_info));
ath79_register_mdio(0, 0x0);
ath79_init_mac(ath79_eth0_data.mac_addr, mac + WPJ563_MAC0_OFFSET, 0);
ath79_init_mac(ath79_eth1_data.mac_addr, mac + WPJ563_MAC1_OFFSET, 0);
/* GMAC0 is connected to an QCA8334 switch */
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
ath79_eth0_data.speed = SPEED_1000;
ath79_eth0_data.duplex = DUPLEX_FULL;
ath79_eth0_data.phy_mask = BIT(0);
ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
ath79_register_eth(0);
}
MIPS_MACHINE(ATH79_MACH_WPJ563, "WPJ563", "Compex WPJ563", WPJ563_setup);

View file

@ -303,6 +303,7 @@ enum ath79_mach_type {
ATH79_MACH_WPJ344, /* Compex WPJ344 */ ATH79_MACH_WPJ344, /* Compex WPJ344 */
ATH79_MACH_WPJ531, /* Compex WPJ531 */ ATH79_MACH_WPJ531, /* Compex WPJ531 */
ATH79_MACH_WPJ558, /* Compex WPJ558 */ ATH79_MACH_WPJ558, /* Compex WPJ558 */
ATH79_MACH_WPJ563, /* Compex WPJ563 */
ATH79_MACH_WPN824N, /* NETGEAR WPN824N */ ATH79_MACH_WPN824N, /* NETGEAR WPN824N */
ATH79_MACH_WRT160NL, /* Linksys WRT160NL */ ATH79_MACH_WRT160NL, /* Linksys WRT160NL */
ATH79_MACH_WRT400N, /* Linksys WRT400N */ ATH79_MACH_WRT400N, /* Linksys WRT400N */

View file

@ -825,3 +825,12 @@ define Device/wpj558
IMAGE_SIZE := 16128k IMAGE_SIZE := 16128k
endef endef
TARGET_DEVICES += wpj558 TARGET_DEVICES += wpj558
define Device/wpj563
DEVICE_TITLE := Compex WPJ563 (16MB flash)
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
BOARDNAME := WPJ563
MTDPARTS := spi0.0:192k(u-boot)ro,16128k(firmware),64k(art)ro
IMAGE_SIZE := 16128k
endef
TARGET_DEVICES += wpj563

View file

@ -191,6 +191,7 @@ CONFIG_ATH79_MACH_RBSXTLITE=y
# CONFIG_ATH79_MACH_WPJ344 is not set # CONFIG_ATH79_MACH_WPJ344 is not set
# CONFIG_ATH79_MACH_WPJ531 is not set # CONFIG_ATH79_MACH_WPJ531 is not set
# CONFIG_ATH79_MACH_WPJ558 is not set # CONFIG_ATH79_MACH_WPJ558 is not set
# CONFIG_ATH79_MACH_WPJ563 is not set
# CONFIG_ATH79_MACH_WRT160NL is not set # CONFIG_ATH79_MACH_WRT160NL is not set
# CONFIG_ATH79_MACH_WRT400N is not set # CONFIG_ATH79_MACH_WRT400N is not set
# CONFIG_ATH79_MACH_WRTNODE2Q is not set # CONFIG_ATH79_MACH_WRTNODE2Q is not set

View file

@ -176,6 +176,7 @@
# CONFIG_ATH79_MACH_WPJ344 is not set # CONFIG_ATH79_MACH_WPJ344 is not set
# CONFIG_ATH79_MACH_WPJ531 is not set # CONFIG_ATH79_MACH_WPJ531 is not set
# CONFIG_ATH79_MACH_WPJ558 is not set # CONFIG_ATH79_MACH_WPJ558 is not set
# CONFIG_ATH79_MACH_WPJ563 is not set
# CONFIG_ATH79_MACH_WRT160NL is not set # CONFIG_ATH79_MACH_WRT160NL is not set
# CONFIG_ATH79_MACH_WRT400N is not set # CONFIG_ATH79_MACH_WRT400N is not set
# CONFIG_ATH79_MACH_WRTNODE2Q is not set # CONFIG_ATH79_MACH_WRTNODE2Q is not set