ath79: add tl-wr1043nd-v4 support everything is working

tplink-safeloader: resize kernel partition
kernel 4.14 is much bigger, resize the partition

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>

target/linux/ath79/base-files/etc/board.d/01_leds

@@ -25,6 +25,13 @@ case "$board" in
 "tplink,tl-mr3020-v1")
 	ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x02"
 	;;
+"tplink,tl-wr1043nd-v4")
+	ucidef_set_led_switch "wan" "WAN" "tp-link:green:wan" "switch0" "0x20"
+	ucidef_set_led_switch "lan1" "LAN1" "tp-link:green:lan1" "switch0" "0x10"
+	ucidef_set_led_switch "lan2" "LAN2" "tp-link:green:lan2" "switch0" "0x08"
+	ucidef_set_led_switch "lan3" "LAN3" "tp-link:green:lan3" "switch0" "0x04"
+	ucidef_set_led_switch "lan4" "LAN4" "tp-link:green:lan4" "switch0" "0x02"
+	;;
 "tplink,tl-wr740n-v2")
 	ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth0"
 	ucidef_set_led_switch "lan1" "LAN1" "$boardname:green:lan1" "switch0" "0x02"

target/linux/ath79/base-files/etc/board.d/02_network

@@ -48,6 +48,10 @@ ath79_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
 		;;
+	"tplink,tl-wr1043nd-v4")
+		ucidef_add_switch "switch0" \
+			"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
+		;;
 	"netgear,wndr3800")
 		ucidef_set_interfaces_lan_wan "eth0" "eth1"
 		ucidef_add_switch "switch0" \

target/linux/ath79/dts/qca9563_tl-wr1043n.dtsi

@@ -0,0 +1,223 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	aliases {
+		led-status = &system;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		system: system {
+			label = "tp-link:green:system";
+			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		usb {
+			label = "tp-link:green:usb";
+			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			trigger-sources = <&hub_port0>;
+			linux,default-trigger = "usbport";
+		};
+
+		wifi_green {
+			label = "tp-link:green:wlan";
+			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wifi_wps {
+			label = "tp-link:green:wps";
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		wan {
+			label = "tp-link:green:wan";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		lan1 {
+			label = "tp-link:green:lan1";
+			gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		lan2 {
+			label = "tp-link:green:lan2";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		lan3 {
+			label = "tp-link:green:lan3";
+			gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		lan4 {
+			label = "tp-link:green:lan4";
+			gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset {
+			label = "Reset button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		wifi {
+			label = "RFKILL button";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+
+	gpio-export {
+		compatible = "gpio-export";
+		#size-cells = <0>;
+
+		gpio_usb_power {
+			gpio-export,name = "tp-link:power:usb";
+			gpio-export,output = <1>;
+			gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&uart {
+	status = "okay";
+};
+
+&gpio {
+	status = "okay";
+};
+
+&usb_phy0 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+
+	hub_port0: port@1 {
+		reg = <1>;
+		#trigger-source-cells = <0>;
+	};
+};
+
+&spi {
+	status = "okay";
+	num-cs = <1>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x020000>;
+				read-only;
+			};
+
+			partition@20000 {
+				label = "firmware";
+				reg = <0x020000 0xf30000>;
+			};
+
+			info: partition@f50000 {
+				label = "product-info";
+				reg = <0xf50000 0x020000>;
+				read-only;
+			};
+
+			partition@f70000 {
+				label = "config";
+				reg = <0xf70000 0x050000>;
+				read-only;
+			};
+
+			partition@fc0000 {
+				label = "partition-table";
+				reg = <0xfc0000 0x010000>;
+				read-only;
+			};
+
+			partition@fd0000 {
+				label = "logs";
+				reg = <0xfd0000 0x020000>;
+				read-only;
+			};
+
+			art: partition@ff0000 {
+				label = "ART";
+				reg = <0xff0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy-mask = <0>;
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		phy-mode = "sgmii";
+
+		qca,ar8327-initvals = <
+		    0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+		    0x7c 0x0000007e /* PORT0_STATUS */
+		>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	mtd-mac-address = <&info 0x8>;
+	phy-handle = <&phy0>;
+};
+
+&wmac {
+	status = "okay";
+	mtd-cal-data = <&art 0x1000>;
+	mtd-mac-address = <&info 0x8>;
+};

target/linux/ath79/dts/qca9563_tl-wr1043nd-v4.dts

@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9563_tl-wr1043n.dtsi"
+
+/ {
+	compatible = "tplink,tl-wr1043nd-v4", "qca,qca9563";
+	model = "TP-Link TL-WR1043ND Version 4";
+};

target/linux/ath79/image/generic-tp-link.mk

@@ -1,16 +1,5 @@
 include ./common-tp-link.mk
 
-
-define Device/tl-wr1043nd-v1
-  $(Device/tplink-8m)
-  ATH_SOC := ar9132
-  DEVICE_TITLE := TP-LINK TL-WR1043N/ND v1
-  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
-  TPLINK_HWID := 0x10430001
-  SUPPORTED_DEVICES := tplink,tl-wr1043nd-v1 tl-wr1043nd
-endef
-TARGET_DEVICES += tl-wr1043nd-v1
-
 define Device/tl-wdr3600
   $(Device/tplink-8mlzma)
   ATH_SOC := ar9344
@@ -28,3 +17,28 @@ define Device/tl-wdr4300
   SUPPORTED_DEVICES := tplink,tl-wdr4300 tl-wdr4300
 endef
 TARGET_DEVICES += tl-wdr4300
+
+define Device/tl-wr1043nd-v1
+  $(Device/tplink-8m)
+  ATH_SOC := ar9132
+  DEVICE_TITLE := TP-LINK TL-WR1043N/ND v1
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
+  TPLINK_HWID := 0x10430001
+  SUPPORTED_DEVICES := tplink,tl-wr1043nd-v1 tl-wr1043nd
+endef
+TARGET_DEVICES += tl-wr1043nd-v1
+
+define Device/tl-wr1043nd-v4
+  $(Device/tplink)
+  ATH_SOC := qca9563
+  IMAGE_SIZE := 15552k
+  DEVICE_TITLE := TP-LINK TL-WR1043N/ND v4
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
+  TPLINK_HWID := 0x10430004
+  TPLINK_BOARD_ID := TLWR1043NDV4
+  KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header
+  IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade
+  IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
+  SUPPORTED_DEVICES := tplink,tl-wr1043nd-v4 tl-wr1043nd-v4
+endef
+TARGET_DEVICES += tl-wr1043nd-v4

tools/firmware-utils/src/tplink-safeloader.c

@@ -779,8 +779,8 @@ static struct device_info boards[] = {
 		*/
 		.partitions = {
 			{"fs-uboot", 0x00000, 0x20000},
-			{"os-image", 0x20000, 0x180000},
+			{"os-image", 0x20000, 0x200000},
-			{"file-system", 0x1a0000, 0xdb0000},
+			{"file-system", 0x220000, 0xd30000},
 			{"default-mac", 0xf50000, 0x00200},
 			{"pin", 0xf50200, 0x00200},
 			{"product-info", 0xf50400, 0x0fc00},