ar71xx: add support for the D-Link DIR-600 rev. A1 board

SVN-Revision: 19100
This commit is contained in:
Gabor Juhos 2010-01-11 08:02:10 +00:00
parent a0f378097e
commit 58301cdeb8
12 changed files with 208 additions and 2 deletions

View file

@ -42,6 +42,9 @@ get_status_led() {
bullet-m | rocket-m | nano-m)
status_led="ubnt:green:link4"
;;
dir-600-a1)
status_led="dir-600-a1:green:power"
;;
dir-615-c1)
status_led="dir-615c1:green:status"
;;

View file

@ -19,6 +19,9 @@ ar71xx_board_name() {
*AW-NR580)
name="aw-nr580"
;;
*"DIR-600 rev. A1")
name="dir-600-a1"
;;
*"DIR-825 rev. B1")
name="dir-825-b1"
;;

View file

@ -68,7 +68,7 @@ platform_check_image() {
[ "$ARGC" -gt 1 ] && return 1
case "$board" in
ap81 | ap83 | dir-615-c1 | dir-825-b1 | mzk-w04nu | mzk-w300nh | tew-632brp | wrt-400n | bullet-m | nano-m | rocket-m)
ap81 | ap83 | dir-600-a1 | dir-615-c1 | dir-825-b1 | mzk-w04nu | mzk-w300nh | tew-632brp | wrt-400n | bullet-m | nano-m | rocket-m)
[ "$magic" != "2705" ] && {
echo "Invalid image type."
return 1

View file

@ -16,6 +16,7 @@ CONFIG_AR71XX_DEV_USB=y
CONFIG_AR71XX_MACH_AP81=y
CONFIG_AR71XX_MACH_AP83=y
CONFIG_AR71XX_MACH_AW_NR580=y
CONFIG_AR71XX_MACH_DIR_600_A1=y
CONFIG_AR71XX_MACH_DIR_615_C1=y
CONFIG_AR71XX_MACH_DIR_825_B1=y
CONFIG_AR71XX_MACH_GENERIC=y

View file

@ -18,6 +18,7 @@ CONFIG_AR71XX_DEV_USB=y
CONFIG_AR71XX_MACH_AP81=y
CONFIG_AR71XX_MACH_AP83=y
CONFIG_AR71XX_MACH_AW_NR580=y
CONFIG_AR71XX_MACH_DIR_600_A1=y
CONFIG_AR71XX_MACH_DIR_615_C1=y
CONFIG_AR71XX_MACH_DIR_825_B1=y
CONFIG_AR71XX_MACH_GENERIC=y

View file

@ -18,6 +18,7 @@ CONFIG_AR71XX_DEV_USB=y
CONFIG_AR71XX_MACH_AP81=y
CONFIG_AR71XX_MACH_AP83=y
CONFIG_AR71XX_MACH_AW_NR580=y
CONFIG_AR71XX_MACH_DIR_600_A1=y
CONFIG_AR71XX_MACH_DIR_615_C1=y
CONFIG_AR71XX_MACH_DIR_825_B1=y
CONFIG_AR71XX_MACH_GENERIC=y

View file

@ -19,6 +19,14 @@ config AR71XX_MACH_AP83
select AR71XX_DEV_USB
default n
config AR71XX_MACH_DIR_600_A1
bool "D-Link DIR-600 rev. A1 support"
select AR71XX_DEV_AP91_PCI if PCI
select AR71XX_DEV_M25P80
select AR71XX_DEV_GPIO_BUTTONS
select AR71XX_DEV_LEDS_GPIO
default n
config AR71XX_MACH_DIR_615_C1
bool "D-Link DIR-615 rev. C1 support"
select AR71XX_DEV_M25P80

View file

@ -28,6 +28,7 @@ obj-$(CONFIG_AR71XX_NVRAM) += nvram.o
obj-$(CONFIG_AR71XX_MACH_AP81) += mach-ap81.o
obj-$(CONFIG_AR71XX_MACH_AP83) += mach-ap83.o
obj-$(CONFIG_AR71XX_MACH_AW_NR580) += mach-aw-nr580.o
obj-$(CONFIG_AR71XX_MACH_DIR_600_A1) += mach-dir-600-a1.o
obj-$(CONFIG_AR71XX_MACH_DIR_615_C1) += mach-dir-615-c1.o
obj-$(CONFIG_AR71XX_MACH_DIR_825_B1) += mach-dir-825-b1.o
obj-$(CONFIG_AR71XX_MACH_GENERIC) += mach-generic.o

View file

@ -0,0 +1,150 @@
/*
* D-Link DIR-600 rev. A1 board support
*
* Copyright (C) 2010 Gabor Juhos <juhosg@openwrt.org>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published
* by the Free Software Foundation.
*/
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <asm/mach-ar71xx/ar71xx.h>
#include "machtype.h"
#include "devices.h"
#include "dev-m25p80.h"
#include "dev-ap91-pci.h"
#include "dev-gpio-buttons.h"
#include "dev-leds-gpio.h"
#define DIR_600_A1_GPIO_LED_WPS 0
#define DIR_600_A1_GPIO_LED_POWER_AMBER 1
#define DIR_600_A1_GPIO_LED_POWER_GREEN 6
#define DIR_600_A1_GPIO_BTN_RESET 8
#define DIR_600_A1_GPIO_BTN_WPS 12
#define DIR_600_A1_BUTTONS_POLL_INTERVAL 20
#ifdef CONFIG_MTD_PARTITIONS
static struct mtd_partition dir_600_a1_partitions[] = {
{
.name = "u-boot",
.offset = 0,
.size = 0x030000,
.mask_flags = MTD_WRITEABLE,
}, {
.name = "nvram",
.offset = 0x030000,
.size = 0x010000,
}, {
.name = "kernel",
.offset = 0x040000,
.size = 0x0e0000,
}, {
.name = "rootfs",
.offset = 0x120000,
.size = 0x2c0000,
}, {
.name = "mac",
.offset = 0x3e0000,
.size = 0x010000,
.mask_flags = MTD_WRITEABLE,
}, {
.name = "art",
.offset = 0x3f0000,
.size = 0x010000,
.mask_flags = MTD_WRITEABLE,
}, {
.name = "firmware",
.offset = 0x040000,
.size = 0x3a0000,
}
};
#endif /* CONFIG_MTD_PARTITIONS */
static struct flash_platform_data dir_600_a1_flash_data = {
#ifdef CONFIG_MTD_PARTITIONS
.parts = dir_600_a1_partitions,
.nr_parts = ARRAY_SIZE(dir_600_a1_partitions),
#endif
};
static struct gpio_led dir_600_a1_leds_gpio[] __initdata = {
{
.name = "dir-600-a1:green:power",
.gpio = DIR_600_A1_GPIO_LED_POWER_GREEN,
}, {
.name = "dir-600-a1:amber:power",
.gpio = DIR_600_A1_GPIO_LED_POWER_AMBER,
}, {
.name = "dir-600-a1:blue:wps",
.gpio = DIR_600_A1_GPIO_LED_WPS,
.active_low = 1,
}
};
static struct gpio_button dir_600_a1_gpio_buttons[] __initdata = {
{
.desc = "reset",
.type = EV_KEY,
.code = BTN_0,
.threshold = 5,
.gpio = DIR_600_A1_GPIO_BTN_RESET,
.active_low = 1,
}, {
.desc = "wps",
.type = EV_KEY,
.code = BTN_1,
.threshold = 5,
.gpio = DIR_600_A1_GPIO_BTN_WPS,
.active_low = 1,
}
};
static void __init dir_600_a1_setup(void)
{
u8 *mac = (u8 *) KSEG1ADDR(0x1fff0000);
u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000);
ar71xx_set_mac_base(mac);
ar71xx_add_device_mdio(0x0);
/* WAN port */
ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RMII;
ar71xx_eth0_data.phy_mask = 0x0;
ar71xx_eth0_data.speed = SPEED_100;
ar71xx_eth0_data.duplex = DUPLEX_FULL;
ar71xx_eth0_data.fifo_cfg1 = 0x0fff0000;
ar71xx_eth0_data.fifo_cfg2 = 0x00001fff;
ar71xx_eth0_data.fifo_cfg3 = 0x008001ff;
/* LAN ports */
ar71xx_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_RMII;
ar71xx_eth1_data.phy_mask = 0x0;
ar71xx_eth1_data.speed = SPEED_1000;
ar71xx_eth1_data.duplex = DUPLEX_FULL;
ar71xx_eth1_data.fifo_cfg1 = 0x0fff0000;
ar71xx_eth1_data.fifo_cfg2 = 0x00001fff;
ar71xx_eth1_data.fifo_cfg3 = 0x008001ff;
ar71xx_add_device_eth(1);
ar71xx_add_device_eth(0);
ar71xx_add_device_m25p80(&dir_600_a1_flash_data);
ar71xx_add_device_leds_gpio(-1, ARRAY_SIZE(dir_600_a1_leds_gpio),
dir_600_a1_leds_gpio);
ar71xx_add_device_gpio_buttons(-1, DIR_600_A1_BUTTONS_POLL_INTERVAL,
ARRAY_SIZE(dir_600_a1_gpio_buttons),
dir_600_a1_gpio_buttons);
ap91_pci_init(ee, NULL);
}
MIPS_MACHINE(AR71XX_MACH_DIR_600_A1, "DIR-600-A1", "D-Link DIR-600 rev. A1",
dir_600_a1_setup);

View file

@ -1,7 +1,7 @@
/*
* Atheros AR71xx machine type definitions
*
* Copyright (C) 2008-2009 Gabor Juhos <juhosg@openwrt.org>
* Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org>
* Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
*
* This program is free software; you can redistribute it and/or modify it
@ -19,6 +19,7 @@ enum ar71xx_mach_type {
AR71XX_MACH_AP81, /* Atheros AP81 */
AR71XX_MACH_AP83, /* Atheros AP83 */
AR71XX_MACH_AW_NR580, /* AzureWave AW-NR580 */
AR71XX_MACH_DIR_600_A1, /* D-Link DIR-600 rev. A1 */
AR71XX_MACH_DIR_615_C1, /* D-Link DIR-615 rev. C1 */
AR71XX_MACH_DIR_825_B1, /* D-Link DIR-825 rev. B1 */
AR71XX_MACH_RB_411, /* MikroTik RouterBOARD 411/411A/411AH */

View file

@ -77,6 +77,26 @@ define Image/Build/WRT400N
fi; fi
endef
dir600a1_mtdlayout=mtdparts=spi0.0:192k(u-boot)ro,64k(nvram)ro,896k(kernel),2816k(rootfs),64k(mac)ro,64k(art)ro,3712k@0x40000(firmware)
define Image/Build/DIR600A1
$(call PatchKernelLzma,$(2),$(3) $(dir600a1_mtdlayout))
if [ `stat -c%s "$(KDIR)/vmlinux-$(2).bin.lzma"` -gt 917504 ]; then \
echo "Warning: $(KDIR)/vmlinux-$(2).bin.lzma is too big"; \
else if [ `stat -c%s $(KDIR)/root.$(1)` -gt 2818048 ]; then \
echo "Warning: $(KDIR)/root.$(1) is too big"; \
else \
mkimage -A mips -O linux -T kernel -a 0x80060000 -C lzma -e \
0x80060000 \
-n 'MIPS OpenWrt Linux-$(LINUX_VERSION)' \
-d $(KDIR)/vmlinux-$(2).bin.lzma $(KDIR)/vmlinux-$(2).uImage; \
( \
dd if=$(KDIR)/vmlinux-$(2).uImage bs=896k conv=sync; \
dd if=$(KDIR)/root.$(1) bs=2752k conv=sync; \
echo -n "AP91-AR7240-RT-090223-00"; \
) > $(call imgname,$(1),$(2))-universal.bin; \
fi; fi
endef
dir825b1_mtdlayout=mtdparts=spi0.0:256k(uboot)ro,64k(config)ro,1024k(kernel),5184k(rootfs),64k(caldata)ro,1600k(unknown)ro,6208k@0x50000(firmware)
define Image/Build/DIR825B1
$(call PatchKernelLzma,$(2),$(3) $(dir825b1_mtdlayout))
@ -328,6 +348,10 @@ define Image/Build/Profile/WP543
$(call Image/Build/Template/64k/$(1),MyLoader,wp543)
endef
define Image/Build/Profile/DIR600A1
$(call Image/Build/Template/64k/$(1),DIR600A1,dir-600-a1,board=DIR-600-A1)
endef
define Image/Build/Profile/DIR615C1
$(call Image/Build/Template/squashfs-only/$(1),Cameo,dir-615-c1,board=DIR-615-C1,"AP81-AR9130-RT-070614-02")
endef
@ -429,6 +453,7 @@ define Image/Build/Profile/Default
$(call Image/Build/Profile/AP81,$(1))
$(call Image/Build/Profile/AP83,$(1))
$(call Image/Build/Profile/A02RBW300N,$(1))
$(call Image/Build/Profile/DIR600A1,$(1))
$(call Image/Build/Profile/DIR615C1,$(1))
$(call Image/Build/Profile/DIR825B1,$(1))
$(call Image/Build/Profile/MZKW04NU,$(1))

View file

@ -5,6 +5,18 @@
# See /LICENSE for more information.
#
define Profile/DIR600A1
NAME:=D-Link DIR-600 rev. A1
PACKAGES:=kmod-ath9k hostapd-mini
endef
define Profile/DIR600A1/Description
Package set optimized for the D-Link DIR-600 rev. A1.
endef
$(eval $(call Profile,DIR600A1))
define Profile/DIR615C1
NAME:=D-Link DIR-615 rev. C1
PACKAGES:=kmod-ath9k hostapd-mini