ath79: add support for I-O DATA WN-AG300DGR

I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros
AR1022.

WN-AG300DGR does not have an LED to indicates power or system status,
I set "router" LED as OpenWrt status LED.

There is no eeprom data for 5 GHz wlan in "art" partition.

Specification:

- Atheros AR1022
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4/5GHz wifi
  - 2.4 GHz: SoC internal
  - 5 GHz: Atheros AR93x2
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- 1x USB 2.0 Type-A
- UART through-hole on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port on WN-AG300DGR
2. Connect power cable to WN-AG300DGR and turn it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit is contained in:
INAGAKI Hiroshi 2018-11-30 19:04:23 +09:00 committed by Mathias Kresin
parent 9dd7147f6b
commit 3358cae523
5 changed files with 245 additions and 2 deletions

View file

@ -82,6 +82,7 @@ ath79_setup_interfaces()
iodata,etg3-r|\
iodata,wn-ac1167dgr|\
iodata,wn-ac1600dgr2|\
iodata,wn-ag300dgr|\
pcs,cr5000)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
@ -223,7 +224,8 @@ ath79_setup_macs()
wan_mac=$(macaddr_add "$lan_mac" -1)
;;
iodata,wn-ac1167dgr|\
iodata,wn-ac1600dgr2)
iodata,wn-ac1600dgr2|\
iodata,wn-ag300dgr)
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
;;

View file

@ -101,7 +101,8 @@ case "$FIRMWARE" in
ath9k_eeprom_extract_reverse "urlader" 5441 1088
;;
iodata,wn-ac1167dgr|\
iodata,wn-ac1600dgr2)
iodata,wn-ac1600dgr2|\
iodata,wn-ag300dgr)
ath9k_eeprom_extract "art" 4096 1088
ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2
;;

View file

@ -13,6 +13,12 @@ PHYNBR=${DEVPATH##*/phy}
board=$(board_name)
case "$board" in
iodata,wn-ag300dgr)
# There is no eeprom data for 5 GHz wlan in "art" partition
# which would allow to patch the macaddress
[ "$PHYNBR" -eq 1 ] && \
echo $(macaddr_add "$(mtd_get_mac_ascii u-boot-env ethaddr)" 1) > /sys${DEVPATH}/macaddress
;;
phicomm,k2t)
# The K2T factory firmware does use LAN mac address as the 2.4G wifi mac address
[ "$PHYNBR" -eq 1 ] && \

View file

@ -0,0 +1,222 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar9344.dtsi"
/ {
compatible = "iodata,wn-ag300dgr", "qca,ar9344";
model = "I-O DATA WN-AG300DGR";
aliases {
led-boot = &router;
led-failsafe = &router;
led-running = &router;
led-upgrade = &router;
};
leds {
compatible = "gpio-leds";
router: router {
label = "wn-ag300dgr:green:router";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
default-state = "on";
};
children {
label = "wn-ag300dgr:green:children";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
default-state = "off";
};
eco {
label = "wn-ag300dgr:green:eco";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
default-state = "off";
};
notification {
label = "wn-ag300dgr:amber:notification";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
default-state = "off";
};
wlan2g {
label = "wn-ag300dgr:green:wlan2g";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "phy0tpt";
};
wlan5g {
label = "wn-ag300dgr:green:wlan5g";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "phy1tpt";
};
};
keys {
compatible = "gpio-keys-polled";
poll-interval = <20>;
eco {
label = "eco";
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
linux,code = <BTN_1>;
debounce-interval = <60>;
};
router {
label = "router";
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
debounce-interval = <60>;
};
auto {
label = "auto";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
debounce-interval = <60>;
};
wps {
label = "wps";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
debounce-interval = <60>;
};
reset {
label = "reset";
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
debounce-interval = <60>;
};
children {
label = "children";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
linux,code = <BTN_1>;
debounce-interval = <60>;
};
};
};
&ref {
clock-frequency = <25000000>;
};
&spi {
num-cs = <1>;
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x030000>;
read-only;
};
partition@30000 {
label = "u-boot-env";
reg = <0x030000 0x010000>;
read-only;
};
partition@40000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x040000 0xf10000>;
};
partition@f50000 {
label = "manufacture";
reg = <0xf50000 0x40000>;
read-only;
};
partition@f90000 {
label = "backup";
reg = <0xf90000 0x10000>;
read-only;
};
partition@fa0000 {
label = "storage";
reg = <0xfa0000 0x50000>;
read-only;
};
partition@ff0000 {
label = "art";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};
&mdio0 {
status = "okay";
phy0: ethernet-phy@0 {
reg = <0>;
phy-mode = "rgmii";
qca,ar8327-initvals = <
0x04 0x07a00000 /* PORT0 PAD MODE CTRL */
0x7c 0x000000fe /* PORT0_STATUS */
>;
};
};
&eth0 {
status = "okay";
pll-data = <0x06000000 0x00000101 0x00001616>;
phy-mode = "rgmii";
phy-handle = <&phy0>;
gmac-config {
device = <&gmac>;
rgmii-gmac0 = <1>;
};
};
&pcie {
status = "okay";
};
&uart {
status = "okay";
};
&usb {
status = "okay";
};
&usb_phy {
status = "okay";
};
&wmac {
status = "okay";
qca,no-eeprom;
};

View file

@ -222,6 +222,18 @@ define Device/iodata_wn-ac1600dgr2
endef
TARGET_DEVICES += iodata_wn-ac1600dgr2
define Device/iodata_wn-ag300dgr
ATH_SOC := ar1022
DEVICE_TITLE := I-O DATA WN-AG300DGR
IMAGE_SIZE := 15424k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
senao-header -r 0x30a -p 0x47 -t 2
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
endef
TARGET_DEVICES += iodata_wn-ag300dgr
define Device/ocedo_koala
ATH_SOC := qca9558
DEVICE_TITLE := OCEDO Koala