ath79: add support for I-O DATA WN-AG300DGR
I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros AR1022. WN-AG300DGR does not have an LED to indicates power or system status, I set "router" LED as OpenWrt status LED. There is no eeprom data for 5 GHz wlan in "art" partition. Specification: - Atheros AR1022 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2T2R 2.4/5GHz wifi - 2.4 GHz: SoC internal - 5 GHz: Atheros AR93x2 - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - 1x USB 2.0 Type-A - UART through-hole on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port on WN-AG300DGR 2. Connect power cable to WN-AG300DGR and turn it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit is contained in:
INAGAKI Hiroshi
Mathias Kresin
parent
9dd7147f6b
commit
3358cae523
5 changed files with 245 additions and 2 deletions
|
|
@ -82,6 +82,7 @@ ath79_setup_interfaces()
|
|||
iodata,etg3-r|\
|
||||
iodata,wn-ac1167dgr|\
|
||||
iodata,wn-ac1600dgr2|\
|
||||
iodata,wn-ag300dgr|\
|
||||
pcs,cr5000)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
|
||||
|
|
@ -223,7 +224,8 @@ ath79_setup_macs()
|
|||
wan_mac=$(macaddr_add "$lan_mac" -1)
|
||||
;;
|
||||
iodata,wn-ac1167dgr|\
|
||||
iodata,wn-ac1600dgr2)
|
||||
iodata,wn-ac1600dgr2|\
|
||||
iodata,wn-ag300dgr)
|
||||
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
||||
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -101,7 +101,8 @@ case "$FIRMWARE" in
|
|||
ath9k_eeprom_extract_reverse "urlader" 5441 1088
|
||||
;;
|
||||
iodata,wn-ac1167dgr|\
|
||||
iodata,wn-ac1600dgr2)
|
||||
iodata,wn-ac1600dgr2|\
|
||||
iodata,wn-ag300dgr)
|
||||
ath9k_eeprom_extract "art" 4096 1088
|
||||
ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -13,6 +13,12 @@ PHYNBR=${DEVPATH##*/phy}
|
|||
board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
iodata,wn-ag300dgr)
|
||||
# There is no eeprom data for 5 GHz wlan in "art" partition
|
||||
# which would allow to patch the macaddress
|
||||
[ "$PHYNBR" -eq 1 ] && \
|
||||
echo $(macaddr_add "$(mtd_get_mac_ascii u-boot-env ethaddr)" 1) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
phicomm,k2t)
|
||||
# The K2T factory firmware does use LAN mac address as the 2.4G wifi mac address
|
||||
[ "$PHYNBR" -eq 1 ] && \
|
||||
|
|
|
|||
222
target/linux/ath79/dts/ar1022_iodata_wn-ag300dgr.dts
Normal file
222
target/linux/ath79/dts/ar1022_iodata_wn-ag300dgr.dts
Normal file
|
|
@ -0,0 +1,222 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "ar9344.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "iodata,wn-ag300dgr", "qca,ar9344";
|
||||
model = "I-O DATA WN-AG300DGR";
|
||||
|
||||
aliases {
|
||||
led-boot = &router;
|
||||
led-failsafe = &router;
|
||||
led-running = &router;
|
||||
led-upgrade = &router;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
router: router {
|
||||
label = "wn-ag300dgr:green:router";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
children {
|
||||
label = "wn-ag300dgr:green:children";
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
eco {
|
||||
label = "wn-ag300dgr:green:eco";
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
notification {
|
||||
label = "wn-ag300dgr:amber:notification";
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "wn-ag300dgr:green:wlan2g";
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "wn-ag300dgr:green:wlan5g";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <20>;
|
||||
|
||||
eco {
|
||||
label = "eco";
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
router {
|
||||
label = "router";
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
auto {
|
||||
label = "auto";
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
children {
|
||||
label = "children";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&ref {
|
||||
clock-frequency = <25000000>;
|
||||
};
|
||||
|
||||
&spi {
|
||||
num-cs = <1>;
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x030000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x030000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x040000 0xf10000>;
|
||||
};
|
||||
|
||||
partition@f50000 {
|
||||
label = "manufacture";
|
||||
reg = <0xf50000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f90000 {
|
||||
label = "backup";
|
||||
reg = <0xf90000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fa0000 {
|
||||
label = "storage";
|
||||
reg = <0xfa0000 0x50000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
phy-mode = "rgmii";
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x07a00000 /* PORT0 PAD MODE CTRL */
|
||||
0x7c 0x000000fe /* PORT0_STATUS */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
pll-data = <0x06000000 0x00000101 0x00001616>;
|
||||
|
||||
phy-mode = "rgmii";
|
||||
phy-handle = <&phy0>;
|
||||
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
rgmii-gmac0 = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
qca,no-eeprom;
|
||||
};
|
||||
|
|
@ -222,6 +222,18 @@ define Device/iodata_wn-ac1600dgr2
|
|||
endef
|
||||
TARGET_DEVICES += iodata_wn-ac1600dgr2
|
||||
|
||||
define Device/iodata_wn-ag300dgr
|
||||
ATH_SOC := ar1022
|
||||
DEVICE_TITLE := I-O DATA WN-AG300DGR
|
||||
IMAGE_SIZE := 15424k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
||||
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
||||
senao-header -r 0x30a -p 0x47 -t 2
|
||||
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
|
||||
endef
|
||||
TARGET_DEVICES += iodata_wn-ag300dgr
|
||||
|
||||
define Device/ocedo_koala
|
||||
ATH_SOC := qca9558
|
||||
DEVICE_TITLE := OCEDO Koala
|
||||
|
|
|
|||
Loading…
Reference in a new issue