openwrtv4/target/linux/generic/patches-3.10/772-bgmac-add-supprot-for-BCM4707.patch

From 2e3759f95d3c96282c19e6f57274d816c6cf1a0e Mon Sep 17 00:00:00 2001
From: Hauke Mehrtens <hauke@hauke-m.de>
Date: Sun, 10 Nov 2013 21:13:20 +0100
Subject: [PATCH 4/5] bgmac: reset all cores on Northstar SoC

On the Northstar SoC (BCM4707 and BCM53018) we have to enable all GMAC
cores when we just want to use on. We iterate over all the cores and
activate them.

Subject: [PATCH 5/5] bgmac: add support for Northstar SoC (BCM4707, BCM53018)

This adds support for the Northstar SoC. This SoC does not have a PMU in
bcma and no register on it should be called. In addition it support 2.5
GBit/s Ethernet to the PHY.

This GMAC core is not fully working there are still problems with the
DMA controller.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

--- a/drivers/net/ethernet/broadcom/bgmac.c
+++ b/drivers/net/ethernet/broadcom/bgmac.c
@@ -825,6 +825,9 @@ static void bgmac_mac_speed(struct bgmac
 	case SPEED_1000:
 		set |= BGMAC_CMDCFG_ES_1000;
 		break;
+	case SPEED_2500:
+		set |= BGMAC_CMDCFG_ES_2500;
+		break;
 	default:
 		bgmac_err(bgmac, "Unsupported speed: %d\n", bgmac->mac_speed);
 	}
@@ -837,12 +840,26 @@ static void bgmac_mac_speed(struct bgmac
 
 static void bgmac_miiconfig(struct bgmac *bgmac)
 {
-	u8 imode = (bgmac_read(bgmac, BGMAC_DEV_STATUS) & BGMAC_DS_MM_MASK) >>
-			BGMAC_DS_MM_SHIFT;
-	if (imode == 0 || imode == 1) {
-		bgmac->mac_speed = SPEED_100;
+	struct bcma_device *core = bgmac->core;
+	struct bcma_chipinfo *ci = &core->bus->chipinfo;
+	u8 imode;
+
+	if (ci->id == BCMA_CHIP_ID_BCM4707 ||
+	    ci->id == BCMA_CHIP_ID_BCM53018) {
+		bcma_awrite32(core, BCMA_IOCTL,
+			      bcma_aread32(core, BCMA_IOCTL) | 0x40 |
+			      BGMAC_BCMA_IOCTL_SW_CLKEN);
+		bgmac->mac_speed = SPEED_2500;
 		bgmac->mac_duplex = DUPLEX_FULL;
 		bgmac_mac_speed(bgmac);
+	} else {
+		imode = (bgmac_read(bgmac, BGMAC_DEV_STATUS) &
+			BGMAC_DS_MM_MASK) >> BGMAC_DS_MM_SHIFT;
+		if (imode == 0 || imode == 1) {
+			bgmac->mac_speed = SPEED_100;
+			bgmac->mac_duplex = DUPLEX_FULL;
+			bgmac_mac_speed(bgmac);
+		}
 	}
 }
 
@@ -886,9 +903,14 @@ static void bgmac_chip_reset(struct bgma
 			flags |= BGMAC_BCMA_IOCTL_SW_RESET;
 	}
 
-	bcma_core_enable(core, flags);
-
-	if (core->id.rev > 2) {
+	/* 3GMAC: for BCM4707, only do core reset at bgmac_probe() */
+	if (ci->id != BCMA_CHIP_ID_BCM4707)
+		bcma_core_enable(core, flags);
+
+	/* Request Misc PLL for corerev > 2 */
+	if (core->id.rev > 2 &&
+	    ci->id != BCMA_CHIP_ID_BCM4707 &&
+	    ci->id != BCMA_CHIP_ID_BCM53018) {
 		bgmac_set(bgmac, BCMA_CLKCTLST,
 			  BGMAC_BCMA_CLKCTLST_MISC_PLL_REQ);
 		bgmac_wait_value(bgmac->core, BCMA_CLKCTLST,
@@ -1026,12 +1048,16 @@ static void bgmac_enable(struct bgmac *b
 		break;
 	}
 
-	rxq_ctl = bgmac_read(bgmac, BGMAC_RXQ_CTL);
-	rxq_ctl &= ~BGMAC_RXQ_CTL_MDP_MASK;
-	bp_clk = bcma_pmu_get_bus_clock(&bgmac->core->bus->drv_cc) / 1000000;
-	mdp = (bp_clk * 128 / 1000) - 3;
-	rxq_ctl |= (mdp << BGMAC_RXQ_CTL_MDP_SHIFT);
-	bgmac_write(bgmac, BGMAC_RXQ_CTL, rxq_ctl);
+	if (ci->id != BCMA_CHIP_ID_BCM4707 &&
+	    ci->id != BCMA_CHIP_ID_BCM53018) {
+		rxq_ctl = bgmac_read(bgmac, BGMAC_RXQ_CTL);
+		rxq_ctl &= ~BGMAC_RXQ_CTL_MDP_MASK;
+		bp_clk = bcma_pmu_get_bus_clock(&bgmac->core->bus->drv_cc) /
+				1000000;
+		mdp = (bp_clk * 128 / 1000) - 3;
+		rxq_ctl |= (mdp << BGMAC_RXQ_CTL_MDP_SHIFT);
+		bgmac_write(bgmac, BGMAC_RXQ_CTL, rxq_ctl);
+	}
 }
 
 /* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipinit */
@@ -1366,6 +1392,7 @@ static int bgmac_probe(struct bcma_devic
 	struct bgmac *bgmac;
 	struct ssb_sprom *sprom = &core->bus->sprom;
 	u8 *mac = core->core_unit ? sprom->et1mac : sprom->et0mac;
+	struct bcma_chipinfo *ci = &core->bus->chipinfo;
 	int err;
 
 	/* We don't support 2nd, 3rd, ... units, SPROM has to be adjusted */
@@ -1404,8 +1431,16 @@ static int bgmac_probe(struct bcma_devic
 	}
 	bgmac->cmn = core->bus->drv_gmac_cmn.core;
 
-	bgmac->phyaddr = core->core_unit ? sprom->et1phyaddr :
-			 sprom->et0phyaddr;
+	/*
+	 * Too much can go wrong in scanning MDC/MDIO playing "whos my phy?" .
+	 * Instead, explicitly use the phy address 30.
+	 */
+	if (ci->id == BCMA_CHIP_ID_BCM4707 || ci->id == BCMA_CHIP_ID_BCM53018)
+		bgmac->phyaddr = BGMAC_PHY_NOREGS;
+	else
+		bgmac->phyaddr = core->core_unit ? sprom->et1phyaddr :
+				 sprom->et0phyaddr;
+
 	bgmac->phyaddr &= BGMAC_PHY_MASK;
 	if (bgmac->phyaddr == BGMAC_PHY_MASK) {
 		bgmac_err(bgmac, "No PHY found\n");
@@ -1423,6 +1458,27 @@ static int bgmac_probe(struct bcma_devic
 
 	bgmac_chip_reset(bgmac);
 
+	/* For Northstar, we have to take all GMAC core out of reset */
+	if (core->id.id == BCMA_CHIP_ID_BCM4707 ||
+	    core->id.id == BCMA_CHIP_ID_BCM53018) {
+		struct bcma_device *ns_core;
+		int ns_gmac;
+
+		/* Northstar has 4 GMAC cores */
+		for (ns_gmac = 0; ns_gmac < 4; ns_gmac++) {
+			/* As northstar requirement, we have to reset all GAMCs
+			 * before accessing one. bgmac_chip_reset() call
+			 * bcma_core_enable() for this core. Then the other
+			 * three GAMCs didn't reset.  We do it here.
+			 */
+			ns_core = bcma_find_core_unit(core->bus,
+						      BCMA_CORE_MAC_GBIT,
+						      ns_gmac);
+			if (ns_core && !bcma_core_is_enabled(ns_core))
+				bcma_core_enable(ns_core, 0);
+		}
+	}
+
 	err = bgmac_dma_alloc(bgmac);
 	if (err) {
 		bgmac_err(bgmac, "Unable to alloc memory for DMA\n");
--- a/drivers/net/ethernet/broadcom/bgmac.h
+++ b/drivers/net/ethernet/broadcom/bgmac.h
@@ -189,6 +189,7 @@
 #define   BGMAC_CMDCFG_ES_10			0x00000000
 #define   BGMAC_CMDCFG_ES_100			0x00000004
 #define   BGMAC_CMDCFG_ES_1000			0x00000008
+#define   BGMAC_CMDCFG_ES_2500			0x0000000C
 #define  BGMAC_CMDCFG_PROM			0x00000010	/* Set to activate promiscuous mode */
 #define  BGMAC_CMDCFG_PAD_EN			0x00000020
 #define  BGMAC_CMDCFG_CF			0x00000040