openwrtv3/target/linux/layerscape/patches-4.4/1101-mtd-spi-nor-fsl-quadspi-extend-support-for-some-spec.patch
Yutang Jiang 15a14cf166 layerscape: add 64b/32b target for ls1012ardb device
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.

The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.

Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
2016-10-31 17:00:10 +01:00

122 lines
3.5 KiB
Diff

From acfc6e9b34b3b3ca0d8bbe366dd08b0fac21c740 Mon Sep 17 00:00:00 2001
From: Yunhui Cui <yunhui.cui@nxp.com>
Date: Tue, 2 Feb 2016 12:21:12 +0800
Subject: [PATCH 101/113] mtd: spi-nor: fsl-quadspi: extend support for some
special requerment.
Add extra info in LUT table to support some special requerments.
Spansion S25FS-S family flash need some special operations.
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
---
drivers/mtd/spi-nor/fsl-quadspi.c | 44 +++++++++++++++++++++++++++++++++++--
include/linux/mtd/spi-nor.h | 4 ++++
2 files changed, 46 insertions(+), 2 deletions(-)
--- a/drivers/mtd/spi-nor/fsl-quadspi.c
+++ b/drivers/mtd/spi-nor/fsl-quadspi.c
@@ -205,6 +205,9 @@
#define SEQID_RDCR 9
#define SEQID_EN4B 10
#define SEQID_BRWR 11
+#define SEQID_RDAR 12
+#define SEQID_WRAR 13
+
#define QUADSPI_MIN_IOMAP SZ_4M
@@ -470,6 +473,28 @@ static void fsl_qspi_init_lut(struct fsl
qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_BRWR),
base + QUADSPI_LUT(lut_base));
+ /*
+ * Read any device register.
+ * Used for Spansion S25FS-S family flash only.
+ */
+ lut_base = SEQID_RDAR * 4;
+ qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_SPANSION_RDAR) |
+ LUT1(ADDR, PAD1, ADDR24BIT),
+ base + QUADSPI_LUT(lut_base));
+ qspi_writel(q, LUT0(DUMMY, PAD1, 8) | LUT1(FSL_READ, PAD1, 1),
+ base + QUADSPI_LUT(lut_base + 1));
+
+ /*
+ * Write any device register.
+ * Used for Spansion S25FS-S family flash only.
+ */
+ lut_base = SEQID_WRAR * 4;
+ qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_SPANSION_WRAR) |
+ LUT1(ADDR, PAD1, ADDR24BIT),
+ base + QUADSPI_LUT(lut_base));
+ qspi_writel(q, LUT0(FSL_WRITE, PAD1, 1),
+ base + QUADSPI_LUT(lut_base + 1));
+
fsl_qspi_lock_lut(q);
}
@@ -477,9 +502,15 @@ static void fsl_qspi_init_lut(struct fsl
static int fsl_qspi_get_seqid(struct fsl_qspi *q, u8 cmd)
{
switch (cmd) {
+ case SPINOR_OP_READ4_1_1_4:
case SPINOR_OP_READ_1_1_4:
case SPINOR_OP_READ_FAST:
+ case SPINOR_OP_READ4_FAST:
return SEQID_READ;
+ case SPINOR_OP_SPANSION_RDAR:
+ return SEQID_RDAR;
+ case SPINOR_OP_SPANSION_WRAR:
+ return SEQID_WRAR;
case SPINOR_OP_WREN:
return SEQID_WREN;
case SPINOR_OP_WRDI:
@@ -491,6 +522,7 @@ static int fsl_qspi_get_seqid(struct fsl
case SPINOR_OP_CHIP_ERASE:
return SEQID_CHIP_ERASE;
case SPINOR_OP_PP:
+ case SPINOR_OP_PP_4B:
return SEQID_PP;
case SPINOR_OP_RDID:
return SEQID_RDID;
@@ -830,8 +862,12 @@ static int fsl_qspi_read_reg(struct spi_
{
int ret;
struct fsl_qspi *q = nor->priv;
+ u32 to = 0;
+
+ if (opcode == SPINOR_OP_SPANSION_RDAR)
+ memcpy(&to, nor->cmd_buf, 4);
- ret = fsl_qspi_runcmd(q, opcode, 0, len);
+ ret = fsl_qspi_runcmd(q, opcode, to, len);
if (ret)
return ret;
@@ -843,9 +879,13 @@ static int fsl_qspi_write_reg(struct spi
{
struct fsl_qspi *q = nor->priv;
int ret;
+ u32 to = 0;
+
+ if (opcode == SPINOR_OP_SPANSION_WRAR)
+ memcpy(&to, nor->cmd_buf, 4);
if (!buf) {
- ret = fsl_qspi_runcmd(q, opcode, 0, 1);
+ ret = fsl_qspi_runcmd(q, opcode, to, 1);
if (ret)
return ret;
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -74,6 +74,10 @@
/* Used for Spansion flashes only. */
#define SPINOR_OP_BRWR 0x17 /* Bank register write */
+/* Used for Spansion S25FS-S family flash only. */
+#define SPINOR_OP_SPANSION_RDAR 0x65 /* Read any device register */
+#define SPINOR_OP_SPANSION_WRAR 0x71 /* Write any device register */
+
/* Used for Micron flashes only. */
#define SPINOR_OP_RD_EVCR 0x65 /* Read EVCR register */
#define SPINOR_OP_WD_EVCR 0x61 /* Write EVCR register */