4aacd6388a
Some of the new ath79 device trees were missing read-only tags on the u-boot partitions. This adds the tags where previously missing. Signed-off-by: Russell Senior <russell@personaltelco.net>
153 lines
2.2 KiB
Text
153 lines
2.2 KiB
Text
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "ar7241.dtsi"
|
|
|
|
/ {
|
|
compatible = "ubnt,xm", "qca,ar7241";
|
|
model = "Ubiquiti Networks XM (rev 1.0) board";
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x2000000>;
|
|
};
|
|
|
|
/* extosc: ref {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <40000000>;
|
|
};
|
|
*/
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
poll-interval = <20>;
|
|
button@0 {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
led@0 {
|
|
label = "ubnt:red:link1";
|
|
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led@1 {
|
|
label = "ubnt:orange:link2";
|
|
gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led@2 {
|
|
label = "ubnt:green:link3";
|
|
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led@3 {
|
|
label = "ubnt:green:link4";
|
|
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
/*&pll {
|
|
clocks = <&extosc>;
|
|
};*/
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "mx25l6405d";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@1 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
partition@2 {
|
|
label = "firmware";
|
|
reg = <0x050000 0x750000>;
|
|
};
|
|
|
|
partition@3 {
|
|
label = "board_config";
|
|
reg = <0x7a0000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@4 {
|
|
label = "cfg";
|
|
reg = <0x7b0000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@5 {
|
|
label = "art";
|
|
reg = <0x7f0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
|
|
ath9k@0000 {
|
|
reg = <0x0000 0 0 0 0>;
|
|
qca,no-eeprom;
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy4: ethernet-phy@4 {
|
|
reg = <4>;
|
|
phy-mode = "mii";
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&art 0x0>;
|
|
|
|
phy-mode = "mii";
|
|
phy-handle = <&phy4>;
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&art 0x6>;
|
|
};
|