openwrtv3/target/linux/brcm63xx/patches-3.14/536-board_fast2704.patch
Jonas Gorski e5cadabb58 brcm63xx: Fix HW553 support
- adsl and lan leds are swapped.
- internetkey is labeled as hspa.
- enable status led and reset button for failsafe.
- use new leds script.
- fix switch configuration.
- remove enet0 from board_info.
- add profile.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41588
2014-07-12 12:31:39 +00:00

145 lines
2.9 KiB
Diff

From: Marcin Jurkowski <marcin1j@gmail.com>
Date: Thu, 31 Oct 2013 22:33:10 +0000
Subject: [PATCH] bcm63xx: Add kernel support for Sagemcom F@ST2704V2 ADSL
router
This adds kernel support support for Sagemcom F@st 2704 wireless ADSL
router.
It's a BCM6328-based 802.11n wireless router with USB port and ADSL2+
modem equipped with 64 MiB RAM and 8 MiB flash.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
---
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
@@ -1468,6 +1468,122 @@ static struct board_info __initdata boar
},
};
+static struct board_info __initdata board_FAST2704V2 = {
+ .name = "F@ST2704V2",
+ .expected_cpu_id = 0x6328,
+
+ .has_uart0 = 1,
+ .has_pci = 1,
+ .has_ohci0 = 1,
+ .has_ehci0 = 1,
+ .has_usbd = 1,
+
+ .has_enetsw = 1,
+
+ .enetsw = {
+ .used_ports = {
+ [0] = {
+ .used = 1,
+ .phy_id = 1,
+ .name = "Port 1",
+ },
+ [1] = {
+ .used = 1,
+ .phy_id = 2,
+ .name = "Port 2",
+ },
+ [2] = {
+ .used = 1,
+ .phy_id = 3,
+ .name = "Port 3",
+ },
+ [3] = {
+ .used = 1,
+ .phy_id = 4,
+ .name = "Port 4",
+ },
+ },
+ },
+
+ .leds = {
+ /* front LEDs */
+ {
+ .name = "F@ST2704V2:green:power",
+ .gpio = 4,
+ .active_low = 1,
+ .default_trigger = "default-on",
+ },
+ {
+ .name = "F@ST2704V2:red:power",
+ .gpio = 5,
+ .active_low = 1,
+ },
+ {
+ .name = "F@ST2704V2:red:inet",
+ .gpio = 2,
+ .active_low = 1,
+ },
+ {
+ .name = "F@ST2704V2:green:dsl",
+ .gpio = 3,
+ .active_low = 1,
+ },
+ {
+ .name = "F@ST2704V2:green:inet",
+ .gpio = 11,
+ .active_low = 1,
+ },
+ {
+ .name = "F@ST2704V2:green:usb",
+ .gpio = 1,
+ .active_low = 1,
+ },
+
+ /* side button LEDs */
+ {
+ .name = "F@ST2704V2:green:wps",
+ .gpio = 10,
+ .active_low = 1,
+ },
+
+ /* FIXME: can't control gpio0 line in "out" state, needs further investigation */
+ /*
+ {
+ .name = "F@ST2704V2:green:rfkill",
+ .gpio = 0,
+ .active_low = 1,
+ },
+ */
+
+ },
+ .buttons = {
+ {
+ .desc = "reset",
+ .gpio = 23,
+ .active_low = 1,
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
+ },
+ {
+ .desc = "wps",
+ .gpio = 24,
+ .active_low = 1,
+ .type = EV_KEY,
+ .code = KEY_WPS_BUTTON,
+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
+ },
+ {
+ .desc = "rfkill",
+ .gpio = 15,
+ .active_low = 1,
+ .type = EV_KEY,
+ .code = KEY_WLAN,
+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
+ },
+ },
+};
+
static struct board_info __initdata board_rta1025w_16 = {
.name = "RTA1025W_16",
.expected_cpu_id = 0x6348,
@@ -3817,6 +3933,7 @@ static const struct board_info __initcon
&board_963281TAN,
&board_A4001N1,
&board_dsl_274xb_f1,
+ &board_FAST2704V2,
#endif
#ifdef CONFIG_BCM63XX_CPU_6338
&board_96338gw,