4e31b2e869
This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47881
349 lines
6.6 KiB
Bash
Executable file
349 lines
6.6 KiB
Bash
Executable file
#!/bin/sh
|
|
|
|
. /lib/functions.sh
|
|
. /lib/ramips.sh
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
ramips_setup_rt3x5x_vlans()
|
|
{
|
|
if [ ! -x /sbin/swconfig ]; then
|
|
# legacy default
|
|
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
|
|
return
|
|
fi
|
|
local wanports=""
|
|
local lanports=""
|
|
for port in 5 4 3 2 1 0; do
|
|
if [ `swconfig dev rt305x port $port get disable` = "1" ]; then
|
|
continue
|
|
fi
|
|
if [ `swconfig dev rt305x port $port get lan` = "0" ]; then
|
|
wanports="$port:wan $wanports"
|
|
else
|
|
lanports="$port:lan $lanports"
|
|
fi
|
|
done
|
|
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
|
|
ucidef_add_switch "rt305x" $lanports $wanports "6@eth0"
|
|
}
|
|
|
|
ramips_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case $board in
|
|
3g150b|\
|
|
3g300m|\
|
|
all0256n|\
|
|
all5002|\
|
|
all5003|\
|
|
broadway|\
|
|
dcs-930|\
|
|
dcs-930l-b1|\
|
|
ht-tm02|\
|
|
linkits7688 | \
|
|
linkits7688d | \
|
|
microwrt|\
|
|
ncs601w|\
|
|
w150m|\
|
|
wnce2001|\
|
|
zte-q7)
|
|
ucidef_add_switch "switch0"
|
|
ucidef_add_switch_attr "switch0" "reset" "false"
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
3g-6200nl|\
|
|
mlw221|\
|
|
mr-102n)
|
|
ucidef_set_interface_lan "eth0.2"
|
|
;;
|
|
3g-6200n|\
|
|
ai-br100|\
|
|
db-wrt01|\
|
|
dir-300-b7|\
|
|
dir-320-b1|\
|
|
dir-610-a1|\
|
|
dir-615-h1|\
|
|
firewrt|\
|
|
hlk-rm04|\
|
|
miwifi-mini|\
|
|
mt7621|\
|
|
mt7628|\
|
|
mzk-750dhp|\
|
|
mzk-w300nh2|\
|
|
oy-0001|\
|
|
pbr-m1|\
|
|
sap-g3200u3|\
|
|
wf-2881|\
|
|
whr-300hp2|\
|
|
whr-600d|\
|
|
witi|\
|
|
wsr-1166|\
|
|
wsr-600|\
|
|
wt1520|\
|
|
y1|\
|
|
zbt-wg2626|\
|
|
youku-yk1)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
|
|
;;
|
|
a5-v11)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "6t@eth0"
|
|
;;
|
|
ar670w|\
|
|
ar725w|\
|
|
rt-n15|\
|
|
wl-351)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "5@eth0"
|
|
;;
|
|
asl26555|\
|
|
re6500|\
|
|
rp-n53)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "6t@eth0"
|
|
;;
|
|
atp-52b|\
|
|
awm002-evb|\
|
|
awm003-evb|\
|
|
dir-645|\
|
|
dir-860l-b1|\
|
|
f5d8235-v1|\
|
|
f5d8235-v2|\
|
|
hg255d|\
|
|
rt-n14u|\
|
|
ubnt-erx|\
|
|
ur-326n4g|\
|
|
wrtnode|\
|
|
wt3020|\
|
|
zbt-wa05)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0"
|
|
;;
|
|
awapn2403)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:wan" "6@eth0"
|
|
;;
|
|
b2c|\
|
|
nw718|\
|
|
psr-680w|\
|
|
sl-r7205|\
|
|
ur-336un|\
|
|
w502u|\
|
|
wr6202)
|
|
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
|
|
;;
|
|
br-6475nd)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
|
|
;;
|
|
cf-wr800n)
|
|
ucidef_add_switch "switch0" \
|
|
"4:lan" "6t@eth0"
|
|
;;
|
|
cy-swr1100)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "9@eth0"
|
|
;;
|
|
d105|\
|
|
hpm|\
|
|
na930|\
|
|
wli-tx4-ag300n)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
e1700|\
|
|
mt7620a_mt7530)
|
|
ucidef_add_switch "switch1" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
|
|
;;
|
|
hc5*61|\
|
|
y1s)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "5:lan" "0:wan" "6@eth0"
|
|
;;
|
|
m2m)
|
|
ucidef_add_switch "switch0"
|
|
ucidef_add_switch_attr "switch0" "reset" "false"
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
mlwg2|\
|
|
wizard8800|\
|
|
wl-330n|\
|
|
wmr-300)
|
|
ucidef_set_interface_lan "eth0.1"
|
|
;;
|
|
mzk-dp150n|\
|
|
vocore)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "4:lan" "6t@eth0"
|
|
;;
|
|
rt-n56u)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "8@eth0"
|
|
;;
|
|
tew-691gr|\
|
|
tew-692gr)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "0@eth0"
|
|
;;
|
|
v11st-fe|\
|
|
wzr-agl300nh)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
|
|
;;
|
|
wcr-150gn)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "6t@eth0"
|
|
;;
|
|
whr-1166d)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "5:wan" "6@eth0"
|
|
;;
|
|
wizfi630a)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "0:wan" "6@eth0"
|
|
;;
|
|
zbt-wr8305rt)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
|
|
;;
|
|
*)
|
|
RT3X5X=`cat /proc/cpuinfo | egrep "(RT3.5|RT5350)"`
|
|
if [ -n "${RT3X5X}" ]; then
|
|
ramips_setup_rt3x5x_vlans
|
|
else
|
|
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
|
|
fi
|
|
;;
|
|
esac
|
|
}
|
|
|
|
ramips_setup_macs()
|
|
{
|
|
local board="$1"
|
|
local lan_mac=""
|
|
local wan_mac=""
|
|
|
|
case $board in
|
|
a5-v11|\
|
|
bc2|\
|
|
broadway|\
|
|
d105|\
|
|
dir-300-b7|\
|
|
dir-320-b1|\
|
|
dir-620-a1|\
|
|
esr-9753|\
|
|
freestation5|\
|
|
hlk-rm04|\
|
|
mpr-a1|\
|
|
mpr-a2|\
|
|
psr-680w|\
|
|
sl-r7205|\
|
|
y1|\
|
|
y1s)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
lan_mac=$(macaddr_setbit_la "$lan_mac")
|
|
wan_mac=$(macaddr_add "$lan_mac" 1)
|
|
;;
|
|
all0239-3g|\
|
|
carambola|\
|
|
freestation5|\
|
|
w502u|\
|
|
wnce2001)
|
|
wan_mac=$(mtd_get_mac_binary factory 46)
|
|
;;
|
|
br-6475nd)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(mtd_get_mac_binary devdata 7)
|
|
;;
|
|
cy-swr1100|\
|
|
dir-645)
|
|
lan_mac=$(mtd_get_mac_ascii nvram lanmac)
|
|
wan_mac=$(mtd_get_mac_ascii nvram wanmac)
|
|
;;
|
|
e1700)
|
|
wan_mac=$(mtd_get_mac_ascii config WAN_MAC_ADDR)
|
|
;;
|
|
hc5*61)
|
|
lan_mac=`mtd_get_mac_ascii bdinfo "Vfac_mac "`
|
|
[ -n "$lan_mac" ] || lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(macaddr_add "$lan_mac" 1)
|
|
;;
|
|
ht-tm02)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
;;
|
|
linkits7688 | \
|
|
linkits7688d)
|
|
wan_mac=$(mtd_get_mac_binary factory 4)
|
|
lan_mac=$(mtd_get_mac_binary factory 46)
|
|
;;
|
|
m3|\
|
|
m4|\
|
|
x5|\
|
|
x8)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
lan_mac=$(macaddr_add "$lan_mac" -2)
|
|
;;
|
|
oy-0001)
|
|
lan_mac=$(mtd_get_mac_binary factory 40)
|
|
wan_mac=$(mtd_get_mac_binary factory 46)
|
|
;;
|
|
rt-n56u)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
lan_mac=$(macaddr_setbit_la "$lan_mac")
|
|
wan_mac=$(mtd_get_mac_binary factory 32772)
|
|
;;
|
|
tew-691gr)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(macaddr_add "$lan_mac" 3)
|
|
;;
|
|
tew-692gr)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(macaddr_add "$lan_mac" 4)
|
|
;;
|
|
tiny-ac)
|
|
lan_mac=$(mtd_get_mac_ascii u-boot-env LAN_MAC_ADDR)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env WAN_MAC_ADDR)
|
|
;;
|
|
w306r-v20)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(macaddr_add "$lan_mac" 5)
|
|
;;
|
|
wcr-150gn)
|
|
wan_mac=$(mtd_get_mac_binary factory 40)
|
|
;;
|
|
whr-1166d|\
|
|
whr-300hp2|\
|
|
whr-600d|\
|
|
wsr-600)
|
|
wan_mac=$(mtd_get_mac_binary factory 4)
|
|
lan_mac=$wan_mac
|
|
;;
|
|
wizfi630a)
|
|
lan_mac=$(mtd_get_mac_binary factory 4)
|
|
wan_mac=$(mtd_get_mac_binary factory 40)
|
|
;;
|
|
wsr-1166)
|
|
local index="$(find_mtd_index "board_data")"
|
|
wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)"
|
|
lan_mac=$wan_mac
|
|
;;
|
|
*)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(macaddr_add "$lan_mac" 1)
|
|
;;
|
|
esac
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr lan $lan_mac
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr wan $wan_mac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(ramips_board_name)
|
|
ramips_setup_interfaces $board
|
|
ramips_setup_macs $board
|
|
board_config_flush
|
|
|
|
exit 0
|