KumiSystems/openwrtv3
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity
openwrtv3/target/linux/lantiq/base-files/etc/board.d/02_network
Johann Neuhauser 02d53e6a21 lantiq: add support for FritzBox 7312 
The FritzBox 7312 is also known as 1&1 WLAN-MODEM. The device is almost
the same as FB7330, but only one ETH-Port and no USB.

Hardware
SoC: Lantiq Xway ARX188 PSB 50812 EL
RAM: 64MB DDR1 (Zentel A4S12D40FTP-G5)
Ethernet: Atheros 8030
Wireless: Atheros AR9227 b/g/n 2x2
DSL: Lantiq ADSL2+
DECT: Dialog SC14441
Buttons: WiFi, DECT
LEDs: Power/DSL, Fon, DECT, WLAN, Info

LEDs
Power: GPIO#44 (active low)
Internet: GPIO#47 (active low)
DECT: GPIO#38 (active low)
WLAN: GPIO#37 (active low)
Info: GPIO#35 (active low)

The Fon LED is labeled as internet in avm gpl sources.

Buttons
WLAN: GPIO#1 (active low)
DECT: GPIO#2 (active low)

Phy
GPIO#03: 25 MHz
GPIO#34: Reset (active low)
GPIO#39: Int
GPIO#42: MII MDIO
GPIO#43: MII MDC

PCIe
GPIO#21: reset (active low)

Installation:

To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put /path/to/openwrt-lantiq-xway-avm_fritz7312-squashfs-sysupgrade.bin mtd1
  ftp> quote REBOOT

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-07-18 19:17:46 +02:00

252 lines
5.9 KiB
Bash
Executable file
Raw Blame History

#!/bin/sh
#
# Copyright (C) 2011-2015 OpenWrt.org
#
. /lib/functions/uci-defaults.sh
. /lib/functions/system.sh
. /lib/functions/lantiq.sh
board_config_update
vpi=1
vci=32
annex="a"
tone="av"
xfer_mode=""
encaps="llc"
payload="bridged"
lan_mac=""
wan_mac=""
interface_wan="dsl0"
board=$(board_name)
case "$board" in
audiocodes,mp-252)
ucidef_add_switch "switch0" \
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5t@eth0"
;;
allnet,all0333cj)
annex="b"
lan_mac=$(mtd_get_mac_ascii uboot_env ethaddr)
wan_mac=$(macaddr_add "$lan_mac" 1)
ucidef_set_interface_lan 'eth0'
;;
arcadyan,arv4510pw)
lan_mac=$(mtd_get_mac_ascii uboot_env ethaddr)
wan_mac=$(macaddr_add "$lan_mac" 1)
ucidef_add_switch "switch0" \
"0:lan:4" "2:lan:2" "1:lan:3" "3:lan:1" "5t@eth0"
;;
arcadyan,arv4519pw|arcadyan,arv7510pw22|arcadyan,arv7518pw)
ucidef_add_switch "switch0" \
"0t@eth0" "2:lan" "3:lan" "4:lan" "5:lan"
;;
arcadyan,arv4520pw)
annex="b"
ucidef_add_switch "switch0" \
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5t@eth0"
;;
arcadyan,arv4525pw|arcadyan,arv452cqw|arcadyan,arv7525pw|arcadyan,arv752dpw)
annex="b"
ucidef_set_interface_lan 'eth0'
;;
arcadyan,arv7506pw11)
annex="b"
wan_mac=$(macaddr_add "$(mtd_get_mac_binary board_config 22)" 2)
ucidef_add_switch "switch0" \
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5t@eth0"
;;
arcadyan,arv7519pw)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary board_config 22)" 1)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4t@eth0"
;;
arcadyan,arv7519rw22)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary boardconfig 22)" 1)
ucidef_add_switch "switch0" \
"0:lan:5" "2:lan:3" "3:lan:4" "4:lan:1" "5:lan:2" "6t@eth0"
;;
arcadyan,arv752dpw22|arcadyan,arv8539pw22)
annex="b"
ucidef_add_switch "switch0" \
"0t@eth0" "2:lan" "3:lan" "4:lan" "5:lan"
;;
alphanetworks,asl56026)
lan_mac=$(mtd_get_mac_ascii uboot_env ethaddr)
wan_mac=$(mtd_get_mac_ascii uboot_env wanmac)
ucidef_add_switch "switch0"\
"2:lan" "3:lan" "6t@eth0"
;;
bt,homehub-v2b)
lan_mac=$(mtd_get_mac_ascii uboot_env ethaddr)
wan_mac=$(macaddr_add "$lan_mac" 1)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "5t@eth0"
;;
bt,homehub-v3a)
lan_mac=$(mtd_get_mac_ascii uboot_env ethaddr)
wan_mac=$(macaddr_add "$lan_mac" 1)
ucidef_set_interface_lan 'eth0'
;;
bt,homehub-v5a)
lan_mac=$(mtd_get_mac_binary_ubi caldata 4364)
wan_mac=$(macaddr_add "$lan_mac" 1)
ucidef_add_switch "switch0" \
"0:lan:3" "1:lan:4" "2:lan:2" "4:lan:1" "5:wan:5" "6t@eth0"
;;
netgear,dgn1000b)
annex="b"
ucidef_set_interface_lan 'eth0'
;;
netgear,dgn3500|netgear,dgn3500b)
lan_mac=$(mtd_get_mac_ascii uboot-env ethaddr)
wan_mac=$(macaddr_add "$lan_mac" 1)
ucidef_add_switch "switch0" \
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5t@eth0"
;;
netgear,dm200)
lan_mac=$(mtd_get_mac_binary ART 0)
wan_mac=$(macaddr_add "$lan_mac" 1)
ucidef_set_interface_lan 'eth0'
;;
lantiq,easy80920-nand|lantiq,easy80920-nor)
lan_mac=$(mtd_get_mac_ascii uboot_env ethaddr)
wan_mac=$(macaddr_add "$lan_mac" 1)
ucidef_add_switch "switch0" \
"0:lan:4" "1:lan:3" "2:lan:2" "4:lan:1" "5:wan:5" "6t@eth0"
;;
avm,fritz3370-rev2-hynix|\
avm,fritz3370-rev2-micron)
annex="b"
lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
wan_mac=$(macaddr_add "$lan_mac" 3)
ucidef_add_switch "switch0" \
"0:lan:3" "1:lan:4" "2:lan:2" "4:lan:1" "6t@eth0"
;;
avm,fritz7312|\
avm,fritz7320)
annex="b"
wan_mac=$(macaddr_add "$(mtd_get_mac_binary urlader 2705)" 1)
ucidef_set_interface_lan 'eth0'
;;
avm,fritz7360sl)
annex="b"
wan_mac=$(macaddr_add "$(mtd_get_mac_binary urlader 2705)" 1)
ucidef_add_switch "switch0" \
"0:lan:3" "1:lan:4" "2:lan:2" "4:lan:1" "6t@eth0"
;;
siemens,gigaset-sx76x)
annex="b"
ucidef_add_switch "switch0" \
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5t@eth0"
;;
zte,h201l)
annex="b"
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4t@eth0"
;;
zyxel,p-2601hn)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "5t@eth0"
;;
zyxel,p-2812hnu-f1|zyxel,p-2812hnu-f3)
lan_mac=$(mtd_get_mac_ascii uboot-env ethaddr)
wan_mac=$(macaddr_add "$lan_mac" 1)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "4:lan" "5:wan" "6t@eth0"
;;
tplink,tdw8970|tplink,tdw8980)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary boardconfig 61696)" 1)
ucidef_add_switch "switch0" \
"0:lan:2" "2:lan:3" "4:lan:4" "5:lan:1" "6t@eth0"
;;
arcadyan,vg3503j)
lan_mac=$(mtd_get_mac_ascii uboot-env ethaddr)
wan_mac=$(macaddr_add "$lan_mac" 1)
ucidef_add_switch "switch0" \
"2:lan:2" "4:lan:1" "6t@eth0"
;;
tplink,vr200v)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary romfile 61696)" 1)
ucidef_add_switch "switch0" \
"0:lan" "2:lan" "4:lan" "5:lan" "6t@eth0"
;;
arcadyan,vgv7510kw22-nor|arcadyan,vgv7510kw22-brn)
annex="b"
wan_mac=$(macaddr_add "$(mtd_get_mac_binary board_config 22)" 2)
ucidef_add_switch "switch0" \
"2:lan:2" "3:lan:1" "4:lan:4" "5:lan:3" "0:wan:5" "6t@eth0"
;;
arcadyan,vgv7519-nor|arcadyan,vgv7519-brn)
wan_mac=$(mtd_get_mac_binary board_config 22)
ucidef_add_switch "switch0" \
"0:lan:4" "1:lan:3" "2:lan:2" "4:lan:1" "5:wan:5" "6t@eth0"
;;
buffalo,wbmr-hp-g300h)
ucidef_add_switch "switch0" \
"0t@eth0" "2:lan" "3:lan" "4:lan" "5:lan"
;;
buffalo,wbmr-300hpd)
lan_mac=$(mtd_get_mac_ascii ubootconfig ethaddr)
wan_mac="$lan_mac"
ucidef_add_switch "switch0" \
"5:lan:2" "2:lan:3" "3:lan:4" "4:wan:1" "6t@eth0"
;;
*)
ucidef_set_interface_lan 'eth0'
;;
esac
ls /lib/modules/$(uname -r)/ltq_atm* 1> /dev/null 2>&1 && \
ucidef_add_atm_bridge "$vpi" "$vci" "$encaps" "$payload" "dsl"
if lantiq_is_vdsl_system; then
ucidef_add_vdsl_modem "$annex" "$tone" "$xfer_mode"
else
ucidef_add_adsl_modem "$annex" "/lib/firmware/adsl.bin"
fi
ucidef_set_interface_wan "$interface_wan" "pppoe"
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" "$lan_mac"
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" "$wan_mac"
board_config_flush
exit 0
Reference in a new issue View git blame Copy permalink