c4931713df
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
165 lines
3.9 KiB
Bash
Executable file
165 lines
3.9 KiB
Bash
Executable file
#!/bin/sh
|
|
|
|
. /lib/functions/system.sh
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/k2t.sh
|
|
|
|
ath79_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
avm,fritz300e|\
|
|
ocedo,koala|\
|
|
ocedo,raccoon|\
|
|
pcs,cap324|\
|
|
tplink,re450-v2|\
|
|
tplink,tl-mr10u|\
|
|
tplink,tl-mr3020-v1|\
|
|
tplink,tl-wr703n|\
|
|
ubnt,unifiac-lite|\
|
|
ubnt,unifiac-mesh|\
|
|
ubnt,unifi)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
buffalo,wzr-hp-g450h)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan"
|
|
;;
|
|
buffalo,bhr-4grv2)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "6@eth0"
|
|
;;
|
|
embeddedwireless,dorin)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:wan" "2:lan:3" "3:lan:2"
|
|
;;
|
|
etactica,eg200)
|
|
ucidef_set_interface_lan "eth0" "dhcp"
|
|
;;
|
|
glinet,ar150|\
|
|
glinet,ar300m)
|
|
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
|
;;
|
|
netgear,wndr3800)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5u@eth0"
|
|
ucidef_add_switch_attr "switch0" "blinkrate" 2
|
|
ucidef_add_switch_port_attr "switch0" 1 led 6
|
|
ucidef_add_switch_port_attr "switch0" 2 led 9
|
|
ucidef_add_switch_port_attr "switch0" 5 led 2
|
|
;;
|
|
netgear,wnr612-v2|\
|
|
on,n150r)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan" "2:lan" "3:lan:3" "4:lan:4"
|
|
;;
|
|
pcs,cr3000)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
|
|
ucidef_set_interface_wan "eth0"
|
|
;;
|
|
pcs,cr5000)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
|
|
;;
|
|
phicomm,k2t)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "3:lan:1" "5:lan:2" "4:wan"
|
|
;;
|
|
tplink,archer-c7-v2)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6@eth0" "1:wan"
|
|
;;
|
|
tplink,tl-mr3220-v1|\
|
|
tplink,tl-mr3420-v1|\
|
|
tplink,tl-wr841-v7)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
tplink,tl-wdr3600|\
|
|
tplink,tl-wdr4300)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan:1" "3:lan:2" "4:lan:3" "5:lan:4" "1:wan"
|
|
;;
|
|
tplink,tl-wr1043nd-v1)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
|
|
;;
|
|
tplink,tl-wr1043nd-v2|\
|
|
tplink,tl-wr1043nd-v3)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" "6@eth0"
|
|
;;
|
|
tplink,tl-wr1043nd-v4)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
|
|
;;
|
|
tplink,tl-wr2543-v1)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
|
|
;;
|
|
tplink,tl-wr740n-v1|\
|
|
tplink,tl-wr740n-v3|\
|
|
tplink,tl-wr741-v1|\
|
|
tplink,tl-wr743nd-v1|\
|
|
tplink,tl-wr841-v5|\
|
|
tplink,tl-wr941-v4)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
|
|
;;
|
|
tplink,tl-wr740nd-v4|\
|
|
tplink,tl-wr741nd-v4)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
tplink,tl-wr841n-v9)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
ubnt,unifiac-mesh-pro|\
|
|
ubnt,unifiac-pro)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan" "3:wan"
|
|
;;
|
|
*)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
ath79_setup_macs()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
avm,fritz300e)
|
|
lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
|
|
;;
|
|
phicomm,k2t)
|
|
lan_mac=$(k2t_get_mac "lan_mac")
|
|
wan_mac=$(k2t_get_mac "wan_mac")
|
|
;;
|
|
tplink,tl-wr1043nd-v4)
|
|
base_mac=$(mtd_get_mac_binary product-info 8)
|
|
wan_mac=$(macaddr_add "$base_mac" 1)
|
|
;;
|
|
esac
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
ath79_setup_interfaces $board
|
|
ath79_setup_macs $board
|
|
board_config_flush
|
|
|
|
exit 0
|