No description
c198ca682c
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> |
||
|---|---|---|
| .github | ||
| config | ||
| include | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| feeds.conf.default | ||
| LICENSE | ||
| Makefile | ||
| README | ||
| rules.mk | ||
This is the buildsystem for the LEDE Linux distribution. Please use "make menuconfig" to choose your preferred configuration for the toolchain and firmware. You need to have installed gcc, binutils, bzip2, flex, python, perl, make, find, grep, diff, unzip, gawk, getopt, subversion, libz-dev and libc headers. Run "./scripts/feeds update -a" to get all the latest package definitions defined in feeds.conf / feeds.conf.default respectively and "./scripts/feeds install -a" to install symlinks of all of them into package/feeds/. Use "make menuconfig" to configure your image. Simply running "make" will build your firmware. It will download all sources, build the cross-compile toolchain, the kernel and all choosen applications. To build your own firmware you need to have access to a Linux, BSD or MacOSX system (case-sensitive filesystem required). Cygwin will not be supported because of the lack of case sensitiveness in the file system. Sunshine! Your LEDE Community http://www.lede-project.org