openwrtv3/target/linux/ramips/dts/WE1026-5G-16M.dts
Kristian Evensen 79440ea756 ramips: Add support for ZBT WE1026-5G
The ZBT WE1026-5G
(http://www.zbtlink.com/products/router/WE1026-5G.html) is the follow-up
to the ZBT WE1026 and is based on MT7620. For the previous WE1026, the
ZBT WE826 image could be used. However, as the name implies, the -5G
comes equipped with a 5GHz wifi radio. As the WE826 only has a 2.4GHz
radio, the addition of 5GHz means that a separate image is needed for
the WE1026-5G. I suspect that this image will also work on the previous
WE1026, but I don't have a device to test with.

The WE1026-5G has following specifications:
* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x 5GHz wifi (MT7612)
* 1x button.
* 3x controllable LEDs.

Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).

Not working:
* The 5GHz WIFI LED is completely dead. I suspect the issue is the same
as on other devices with Mediatek 5Ghz wifi-cards/chips. The LED is
controlled by the driver, and mt76 (currently) does not support this.

Not tested:
* SD card reader.

Notes:
* The modem (labeled 3G/4G) and power LEDs are controlled by the
hardware.
* There is a 32MB version of this device available, but I do not have
access to it. I have therefor only added support for the 16MB version,
but added all the required infrastructure to make adding support for the
32MB version easy.

Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.

Recovery:
If you brick the device, the WE1026-5G supports recovery using HTTP. Keep the
reset button pressed for ~5sec when booting to start the web server. Set the
address of the network interface on your machine to 192.168.1.2/24, and
point your browser to 192.168.1.1 to access the recovery UI. From the
recovery UI you can upload a firmware image.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-09-11 17:17:05 +02:00

76 lines
2.3 KiB
Text

/*
* BSD LICENSE
*
* Copyright(c) 2017 Kristian Evensen <kristian.evensen@gmail.com>.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* * Neither the name of Broadcom Corporation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/dts-v1/;
#include "WE1026-5G.dtsi"
/ {
compatible = "zbtlink,we1026-5g-16m", "ralink,mt7620a-soc";
model = "ZBT WE1026-5G (16M)";
};
&spi0 {
status = "okay";
en25q128@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <10000000>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "u-boot-env";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
firmware: partition@50000 {
label = "firmware";
reg = <0x50000 0xfb0000>;
};
};
};