openwrtv3/target/linux/lantiq/dts/ARV7519PW.dts
Mathias Kresin 91d5067091 lantiq: use the etop driver DT bindings only
Use the generic mtd-mac-address dts property to get a mac address from
flash instead of the lantiq specific one.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-10 02:04:31 +02:00

224 lines
3.6 KiB
Text

/dts-v1/;
/include/ "danube.dtsi"
/ {
model = "ARV7519PW - Astoria Networks";
chosen {
bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
leds {
boot = &power;
failsafe = &power2;
running = &power;
dsl = &dsl;
internet = &online;
wifi = &wifi;
};
};
memory@0 {
reg = <0x0 0x4000000>;
};
sram@1F000000 {
vmmc@107000 {
status = "okay";
};
};
fpi@10000000 {
localbus@0 {
nor-boot@0 {
compatible = "lantiq,nor";
bank-width = <2>;
reg = <0 0x0 0x2000000>;
#address-cells = <1>;
#size-cells = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "uboot";
reg = <0x00000 0x40000>;
read-only;
};
partition@40000 {
label = "uboot_env";
reg = <0x40000 0x20000>;
};
partition@60000 {
label = "firmware";
reg = <0x60000 0xf80000>;
};
boardconfig: partition@fe0000 {
label = "board_config";
reg = <0xfe0000 0x20000>;
read-only;
};
};
};
};
gpio: pinmux@E100B10 {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
ebu {
lantiq,groups = "ebu cs1";
lantiq,function = "ebu";
};
pci_in {
lantiq,groups = "req1";
lantiq,function = "pci";
lantiq,open-drain = <1>;
lantiq,pull = <2>;
lantiq,output = <0>;
};
pci_out {
lantiq,groups = "gnt1";
lantiq,function = "pci";
lantiq,pull = <0>;
lantiq,output = <1>;
};
pci_rst {
lantiq,pins = "io21";
lantiq,pull = <2>;
lantiq,output = <1>;
};
switch_rst {
lantiq,pins = "io19";
lantiq,pull = <2>;
lantiq,output = <1>;
};
};
};
etop@E180000 {
phy-mode = "mii";
mtd-mac-address = <&boardconfig 0x16>;
};
/* warning: passive port
only works with active devices */
ifxhcd@E101000 {
status = "okay";
};
pci@E105400 {
status = "okay";
lantiq,external-clock;
gpio-reset = <&gpio 21 0>;
req-mask = <0xf>;
};
};
ralink_eep {
compatible = "ralink,eeprom";
ralink,eeprom = "RT2860.eeprom";
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
rfkill {
label = "rfkill";
gpios = <&gpio 11 1>;
linux,code = <0xf7>;
};
reset {
label = "reset";
gpios = <&gpio 28 1>;
linux,code = <0x198>;
};
};
gpio-leds {
compatible = "gpio-leds";
power: power {
label = "power";
gpios = <&gpio 2 1>;
default-state = "keep";
};
power2: power2 {
label = "power2";
gpios = <&gpio 14 1>;
};
online: online {
label = "online";
gpios = <&gpio 3 1>;
};
online2 {
label = "online2";
gpios = <&gpio 30 1>;
};
wifi: wifi {
label = "wifi";
gpios = <&gpio 12 1>;
};
wifi2 {
label = "wifi2";
gpios = <&gpio 10 1>;
};
wifi3 {
label = "wifi3";
gpios = <&gpio 6 1>;
};
voice {
label = "voice";
gpios = <&gpio 31 1>;
};
wps {
label = "wps";
gpios = <&gpio 15 1>;
};
wps2 {
label = "wps2";
gpios = <&gpio 7 1>;
};
wps3 {
label = "wps3";
gpios = <&gpio 23 1>;
};
dsl: dsl {
label = "dsl";
gpios = <&gpio 4 1>;
};
lan {
label = "lan";
gpios = <&gpio 1 1>;
};
tv {
label = "tv";
gpios = <&gpio 20 1>;
};
upgrade {
label = "upgrade";
gpios = <&gpio 29 1>;
};
};
/* is there another way to "reserve" the GPIO? */
gpio_export {
compatible = "gpio-export";
#size-cells = <0>;
switch {
gpio-export,name = "switch";
gpio-export,output = <1>;
gpios = <&gpio 19 0>;
};
};
};