openwrtv3/target/linux/lantiq/dts/BTHOMEHUBV3A.dts
blogic b7fc892eb5 lantiq: move partitions into partion table node
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49280
2016-05-10 10:43:12 +02:00

223 lines
4.3 KiB
Text

/dts-v1/;
/include/ "ar9.dtsi"
/ {
model = "BTHOMEHUBV3A - BT Home Hub 3A"; /* SoC: Lantiq ar9 @ 333MHz */
chosen {
bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
leds {
boot = &power_orange;
failsafe = &power_red;
running = &power_blue;
internet = &broadband_blue;
wifi = &wireless_blue;
};
};
memory@0 { /* RAM: Samsung K4H511638F-LC 64MB */
reg = <0x0 0x4000000>;
};
sram@1F000000 {
vmmc@107000 {
status = "okay";
gpios = <&gpio 31 0>;
};
};
fpi@10000000 {
#address-cells = <1>;
#size-cells = <1>;
localbus@0 {
#address-cells = <2>;
#size-cells = <1>;
ranges = <0 0 0x0 0x3ffffff /* addrsel0 */
1 0 0x4000000 0x4000010>; /* addsel1 */
compatible = "lantiq,localbus", "simple-bus";
nand-parts@0 { /* NAND Flash: Samsung K9F5608U0D-JIB0 32MB */
compatible = "gen_nand", "lantiq,nand-xway";
lantiq,cs = <1>;
bank-width = <2>;
reg = <1 0x0 0x2000000 >;
#address-cells = <1>;
#size-cells = <1>;
req-mask = <0x1>; /* PCI request lines to mask during NAND access */
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "preboot";
reg = <0x00000 0x8000>;
read-only;
};
partition@8000 {
label = "u-boot";
reg = <0x8000 0x05c000>;
read-only;
};
partition@64000 {
label = "uboot-config";
reg = <0x64000 0x004000>;
};
ath9k_cal: partition@68000 {
label = "art-copy";
reg = <0x68000 0x004000>;
};
partition@6c000 {
label = "kernel";
reg = <0x6c000 0x200000>;
};
partition@26c000 {
label = "ubi";
reg = <0x26c000 0x1d94000>;
};
};
};
ath9k_eep {
compatible = "ath9k,eeprom";
ath,eep-flash = <&ath9k_cal 0x0000>;
ath,mac-offset = <0x10c>;
ath,pci-slot = <14>;
ath,eep-endian;
};
};
gpio: pinmux@E100B10 {
compatible = "lantiq,pinctrl-xr9";
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
#gpio-cells = <2>;
gpio-controller;
reg = <0xE100B10 0xA0>;
state_default: pinmux {
nand_out {
lantiq,groups = "nand cle", "nand ale";
lantiq,function = "ebu";
lantiq,output = <1>;
lantiq,open-drain = <0>;
lantiq,pull = <0>;
};
nand_cs1 {
lantiq,groups = "nand cs1";
lantiq,function = "ebu";
lantiq,open-drain = <0>;
lantiq,pull = <0>;
};
pci_in {
lantiq,groups = "req1";
lantiq,function = "pci";
lantiq,output = <0>;
lantiq,open-drain = <1>;
lantiq,pull = <2>;
};
pci_out {
lantiq,groups = "gnt1";
lantiq,function = "pci";
lantiq,output = <1>;
lantiq,open-drain = <0>;
lantiq,pull = <0>;
};
pci_rst {
lantiq,pins = "io21";
lantiq,output = <1>;
lantiq,open-drain = <0>;
};
};
};
etop@E180000 {
phy-mode = "rgmii";
};
ifxhcd@E101000 {
status = "okay";
gpios = <&gpio 33 0>;
};
pci@E105400 {
status = "okay";
gpio-reset = <&gpio 21 0>;
};
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
reset {
label = "reset";
gpios = <&gpio 54 1>;
linux,code = <0x198>;
};
restart {
label = "restart";
gpios = <&gpio 52 1>;
linux,code = <0x198>;
};
wps {
label = "wps";
gpios = <&gpio 53 1>;
linux,code = <0x211>;
};
};
gpio-leds {
compatible = "gpio-leds";
wireless-red {
label = "bthomehubv3a:red:wireless";
gpios = <&gpio 2 1>;
};
wireless-orange {
label = "bthomehubv3a:orange:wireless";
gpios = <&gpio 6 1>;
};
wireless_blue: wireless-blue {
label = "bthomehubv3a:blue:wireless";
gpios = <&gpio 9 1>;
};
broadband-red {
label = "bthomehubv3a:red:broadband";
gpios = <&gpio 11 1>;
};
broadband-orange {
label = "bthomehubv3a:orange:broadband";
gpios = <&gpio 0 1>;
};
broadband_blue: broadband-blue {
label = "bthomehubv3a:blue:broadband";
gpios = <&gpio 12 1>;
};
power_red: power-red {
label = "bthomehubv3a:red:power";
gpios = <&gpio 14 1>;
};
power_orange: power-orange {
label = "bthomehubv3a:orange:power";
gpios = <&gpio 5 1>;
default-state = "keep";
};
power_blue: power-blue {
label = "bthomehubv3a:blue:power";
gpios = <&gpio 1 1>;
};
};
};