c9e9a78734
Indicate a (sys)upgrade via leds as well. It brings the lantiq diag.sh script en par with the other implementations using devicetree aliases to define multiple leds for boot status indication. By default, use the boot finished led to indicate an upgrade for now. Signed-off-by: Mathias Kresin <dev@kresin.me>
182 lines
3.2 KiB
Text
182 lines
3.2 KiB
Text
/dts-v1/;
|
|
|
|
#include "ar9.dtsi"
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "avm,fritz7312", "lantiq,xway", "lantiq,ar9";
|
|
model = "FritzBox 7312 (1&1 WLAN-MODEM)";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyLTQ0,115200";
|
|
};
|
|
|
|
aliases {
|
|
led-boot = &power;
|
|
led-failsafe = &power;
|
|
led-running = &power;
|
|
led-upgrade = &power;
|
|
|
|
led-internet = &info_green;
|
|
led-dsl = &power;
|
|
led-wifi = &wlan;
|
|
};
|
|
|
|
memory@0 {
|
|
reg = <0x0 0x4000000>;
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <100>;
|
|
|
|
wlan {
|
|
label = "wlan";
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RFKILL>;
|
|
};
|
|
dect {
|
|
label = "dect";
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_PHONE>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power: power {
|
|
label = "fritz7312:green:power";
|
|
gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
|
|
default-state = "keep";
|
|
};
|
|
voice {
|
|
label = "fritz7312:green:fon";
|
|
gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
|
|
};
|
|
dect {
|
|
label = "fritz7312:green:dect";
|
|
gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
|
|
};
|
|
wlan: wlan {
|
|
label = "fritz7312:green:wlan";
|
|
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
|
|
};
|
|
info_green: info_green {
|
|
label = "fritz7312:green:info";
|
|
gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&state_default>;
|
|
|
|
state_default: pinmux {
|
|
pci {
|
|
lantiq,groups = "gnt1", "req1", "req2", "req4", "gnt2", "gnt3", "gnt4";
|
|
lantiq,function = "pci";
|
|
};
|
|
pci-in {
|
|
lantiq,groups = "req1", "req2", "req4";
|
|
lantiq,output = <0>;
|
|
lantiq,open-drain = <1>;
|
|
lantiq,pull = <2>;
|
|
};
|
|
pci-out {
|
|
lantiq,groups = "gnt1", "gnt2", "gnt3", "gnt4";
|
|
lantiq,output = <1>;
|
|
lantiq,pull = <0>;
|
|
};
|
|
ar8030-intr {
|
|
lantiq,groups = "exin3";
|
|
lantiq,function = "exin";
|
|
lantiq,pull = <2>;
|
|
lantiq,output = <0>;
|
|
};
|
|
ar8030-clk {
|
|
lantiq,groups = "clkout2";
|
|
lantiq,output = <1>;
|
|
lantiq,open-drain;
|
|
};
|
|
ar8030-rst {
|
|
lantiq,pins = "io34";
|
|
lantiq,output = <1>;
|
|
lantiq,pull = <2>;
|
|
lantiq,open-drain;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gsw {
|
|
phy-mode = "rmii";
|
|
phy-handle = <&phy0>;
|
|
mtd-mac-address = <&ath9k_cal 0xa91>;
|
|
mtd-mac-address-increment = <(-2)>;
|
|
|
|
mdio-bus {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0>;
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
reset-gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&localbus {
|
|
nor@0 {
|
|
compatible = "lantiq,nor";
|
|
bank-width = <2>;
|
|
reg = <0 0x0 0x1000000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
ath9k_cal: partition@0 {
|
|
label = "urlader";
|
|
reg = <0x00000 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
label = "firmware";
|
|
reg = <0x20000 0xf60000>;
|
|
};
|
|
|
|
partition@f80000 {
|
|
label = "tffs (1)";
|
|
reg = <0xf80000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@fc0000 {
|
|
label = "tffs (2)";
|
|
reg = <0xfc0000 0x40000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pci0 {
|
|
status = "okay";
|
|
req-mask = <0xf>;
|
|
gpio-reset = <&gpio 21 GPIO_ACTIVE_LOW>;
|
|
|
|
wifi@0,0 {
|
|
compatible = "pci0,0";
|
|
reg = <0x7000 0 0 0 0>;
|
|
qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */
|
|
};
|
|
};
|