openwrtv3/target/linux/ramips/dts/WHR-1166D.dts
Mathias Kresin 8c9f847a80 ramips: fix WHR-1166D WAN port
By adding the ICPlus IP1001 phy driver an already set RGMII delay mode
is reset during driver load.

Set the rgmii rx delay to fix corrupt/no packages in case the WAN port
negotiates to 1000MBit.

Fixes: FS#670

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-11 18:12:56 +02:00

172 lines
2.7 KiB
Text

/dts-v1/;
#include "mt7620a.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "buffalo,whr-1166d", "ralink,mt7620a-soc";
model = "Buffalo WHR-1166D";
gpio-leds {
compatible = "gpio-leds";
power {
label = "whr-1166d:red:power";
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
};
wifi {
label = "whr-1166d:green:wifi";
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
};
power2 {
label = "whr-1166d:green:power";
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
};
wifi2 {
label = "whr-1166d:orange:wifi";
gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
};
internet {
label = "whr-1166d:green:internet";
gpios = <&gpio2 17 GPIO_ACTIVE_LOW>;
};
router {
label = "whr-1166d:orange:router";
gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
};
router2 {
label = "whr-1166d:green:router";
gpios = <&gpio2 19 GPIO_ACTIVE_LOW>;
};
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <20>;
reset {
label = "reset";
gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
aoss {
label = "aoss";
gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
ap {
label = "ap";
gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
};
bridge {
label = "bridge";
gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
};
};
};
&gpio2 {
status = "okay";
};
&spi0 {
status = "okay";
m25p80@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <10000000>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "u-boot-env";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
label = "firmware";
reg = <0x50000 0xfb0000>;
};
};
};
&pinctrl {
state_default: pinctrl0 {
gpio {
ralink,group = "i2c", "uartf", "wled", "nd_sd";
ralink,function = "gpio";
};
};
};
&ethernet {
pinctrl-names = "default";
pinctrl-0 = <&rgmii1_pins &mdio_pins>;
port@5 {
status = "okay";
phy-handle = <&phy5>;
phy-mode = "rgmii";
};
mdio-bus {
status = "okay";
phy5: ethernet-phy@5 {
reg = <5>;
phy-mode = "rgmii-rxid";
};
};
};
&gsw {
mediatek,port4 = "ephy";
};
&wmac {
ralink,mtd-eeprom = <&factory 0>;
};
&pcie {
status = "okay";
pcie-bridge {
wifi@0,0 {
compatible = "pci0,0";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
ieee80211-freq-limit = <5000000 6000000>;
};
};
};