8f4dfadd5a
Use diag.sh version used for other targets supporting different leds for the different boot states. The existing led sequences should be the same as before. Signed-off-by: Mathias Kresin <dev@kresin.me>
150 lines
2.6 KiB
Text
150 lines
2.6 KiB
Text
/dts-v1/;
|
|
|
|
#include "rt3883.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "trendnet,tew-692gr", "ralink,rt3883-soc";
|
|
model = "TRENDnet TEW-692GR";
|
|
|
|
aliases {
|
|
led-boot = &led_wps_green;
|
|
led-failsafe = &led_wps_green;
|
|
led-running = &led_wps_green;
|
|
led-upgrade = &led_wps_green;
|
|
};
|
|
|
|
nor-flash@1c000000 {
|
|
compatible = "cfi-flash";
|
|
reg = <0x1c000000 0x800000>;
|
|
bank-width = <2>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
reg = <0x0 0x0030000>;
|
|
label = "u-boot";
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
reg = <0x00030000 0x00010000>;
|
|
label = "u-boot-env";
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
reg = <0x00040000 0x00010000>;
|
|
label = "factory";
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
reg = <0x00050000 0x007b0000>;
|
|
label = "firmware";
|
|
};
|
|
};
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <100>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wps {
|
|
label = "tew-692gr:orange:wps";
|
|
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_wps_green: wps2 {
|
|
label = "tew-692gr:green:wps";
|
|
gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&pinctrl {
|
|
state_default: pinctrl0 {
|
|
gpio {
|
|
ralink,group = "spi", "i2c", "jtag", "uartf";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
status = "okay";
|
|
mtd-mac-address = <&factory 0x4>;
|
|
|
|
port@0 {
|
|
phy-handle = <&phy0>;
|
|
phy-mode = "rgmii";
|
|
};
|
|
|
|
mdio-bus {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
phy-mode = "rgmii";
|
|
|
|
qca,ar8327-initvals = <
|
|
0x04 0x07600000 /* PORT0 PAD MODE CTRL */
|
|
0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
|
|
0x10 0x40000000 /* Power-on Strapping: 176-pin interface configuration */
|
|
0x50 0xc437c437 /* LED Control Register 0 */
|
|
0x54 0xc337c337 /* LED Control Register 1 */
|
|
0x58 0x00000000 /* LED Control Register 2 */
|
|
0x5c 0x03ffff00 /* LED Control Register 3 */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
0x94 0x0000007e /* PORT6 STATUS */
|
|
>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pci {
|
|
status = "okay";
|
|
};
|
|
|
|
&pci1 {
|
|
status = "okay";
|
|
|
|
wifi@0,0 {
|
|
compatible = "pci0,0";
|
|
reg = < 0x10000 0 0 0 0 >;
|
|
ralink,2ghz = <0>;
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
ralink,mtd-eeprom = <&factory 0x0>;
|
|
ralink,5ghz = <0>;
|
|
mtd-mac-address = <&factory 0x4>;
|
|
mtd-mac-address-increment = <3>;
|
|
};
|