7a873974f7
Use diag.sh version used for apm821xx, ipq40xx and ipq806x, which supports different leds for the different boot states. The existing led sequences should be the same as before. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> [reword commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
168 lines
2.7 KiB
Text
168 lines
2.7 KiB
Text
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "ar7242.dtsi"
|
|
|
|
/ {
|
|
compatible = "avm,fritz300e", "qca,ar7242";
|
|
model = "AVM FRITZ!WLAN Repeater 300E";
|
|
|
|
aliases {
|
|
led-boot = &power;
|
|
led-failsafe = &power;
|
|
led-running = &power;
|
|
led-upgrade = &power;
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <20>;
|
|
|
|
wps {
|
|
label = "wps";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power: power {
|
|
label = "fritz300e:green:power";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
lan {
|
|
label = "fritz300e:green:lan";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan {
|
|
label = "fritz300e:green:wlan";
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
|
|
ath9k-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
rssi0 {
|
|
label = "fritz300e:green:rssi0";
|
|
gpios = <&ath9k 10 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
rssi1 {
|
|
label = "fritz300e:green:rssi1";
|
|
gpios = <&ath9k 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
rssi2 {
|
|
label = "fritz300e:green:rssi2";
|
|
gpios = <&ath9k 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
rssi3 {
|
|
label = "fritz300e:green:rssi3";
|
|
gpios = <&ath9k 7 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
rssi4 {
|
|
label = "fritz300e:green:rssi4";
|
|
gpios = <&ath9k 5 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
eth-phy-reset {
|
|
compatible = "regulator-fixed";
|
|
|
|
regulator-name = "eth-phy-reset";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
|
|
gpio = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
startup-delay-us = <300000>;
|
|
enable-active-high;
|
|
|
|
regulator-always-on;
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
reg = <0x0 0x20000>;
|
|
label = "urloader";
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
reg = <0x20000 0xee0000>;
|
|
label = "firmware";
|
|
};
|
|
|
|
partition@f00000 {
|
|
reg = <0xf00000 0x80000>;
|
|
label = "tffs (1)";
|
|
read-only;
|
|
};
|
|
|
|
partition@f80000 {
|
|
reg = <0xf80000 0x80000>;
|
|
label = "tffs (2)";
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
|
|
ath9k: wifi@0,0 {
|
|
reg = <0x0000 0 0 0 0>;
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
qca,no-eeprom;
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
phy-mode = "rgmii";
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-mode = "rgmii";
|
|
phy-handle = <&phy0>;
|
|
|
|
pll-data = <0x16000000 0x00000101 0x00001313>;
|
|
};
|