745dee11ac
This patch ports over support for the device from ar71xx.
SOC: AR7370 (Wasp - AR9344 rev2 0001974c)
RAM: Winbond W9725G6KB-25 32MiB
FLASH: Winbond 25Q64FVSIG 8MiB
WLAN: AR9380 Dual-Band 802.11abgn 3x3:3
INPUT: WPS, RESET button (hardware on/off toggle button)
LED: Power, LAN, WiFi, 3 RSSI-Leds (low, medium, high)
Serial: Header Next to the winbond flash chip (labeld JP1)
Pinout is GND - NC - RX - TX - 3V3 (JP1)
The Serial setting is 115200-8-N-1.
- Installation via uboot's upgrade command
0. attach serial cable
1. interrupt uboot and enter "upgrade code.bin" into
the u-boot prompt
ar7240> upgrade code.bin
2. rename openwrt...sysupgrade.bin to code.bin on PC
3. run a tftp-client on the PC
(shell)$ tftp 192.168.1.230
binary
put code.bin
4. wait for the device to finish
[...]
Copy buff to Flash from 0x9f040000 length 0x79f000
Copy to Flash... write addr: 9f040000
done
5. enter "go" in the u-boot prompt
ar7240> go
- TFTP ramdisk image boot from the uboot prompt
(tftp server defaults to serverip 192.168.1.254)
=> tftpboot 81000000 initramfs.bin
=> bootm
Tested and working:
- LEDs
- Buttons
- Ethernet
- Wi-Fi
- OpenWRT sysupgrade
For flashing and debricking information see:
<https://openwrt.org/toh/wd/rext>
Users coming from ar71xx can use sysupgrade too. But I highly
advise to no save the old configuration and start from a clean
state.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
226 lines
5.5 KiB
Bash
Executable file
226 lines
5.5 KiB
Bash
Executable file
#!/bin/sh
|
|
|
|
. /lib/functions/system.sh
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/k2t.sh
|
|
|
|
ath79_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
avm,fritz300e|\
|
|
ocedo,koala|\
|
|
ocedo,raccoon|\
|
|
pcs,cap324|\
|
|
pisen,wmm003n|\
|
|
tplink,re450-v2|\
|
|
tplink,tl-mr10u|\
|
|
tplink,tl-mr3020-v1|\
|
|
tplink,tl-mr3040-v2|\
|
|
tplink,tl-wr703n|\
|
|
ubnt,bullet-m|\
|
|
ubnt,rocket-m|\
|
|
ubnt,unifiac-lite|\
|
|
ubnt,unifiac-mesh|\
|
|
ubnt,unifi|\
|
|
wd,mynet-wifi-rangeextender)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
buffalo,wzr-hp-g450h)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan"
|
|
;;
|
|
buffalo,bhr-4grv2)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "6@eth0"
|
|
;;
|
|
dlink,dir-825-b1)
|
|
ucidef_set_interface_wan "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "5@eth0"
|
|
;;
|
|
embeddedwireless,dorin)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:wan" "2:lan:3" "3:lan:2"
|
|
;;
|
|
etactica,eg200)
|
|
ucidef_set_interface_lan "eth0" "dhcp"
|
|
;;
|
|
avm,fritz4020|\
|
|
glinet,ar150|\
|
|
glinet,ar300m)
|
|
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
|
;;
|
|
iodata,etg3-r|\
|
|
iodata,wn-ac1167dgr|\
|
|
iodata,wn-ac1600dgr2|\
|
|
pcs,cr5000)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
|
|
;;
|
|
netgear,wndr3700|\
|
|
netgear,wndr3700v2|\
|
|
netgear,wndr3800)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5u@eth0"
|
|
ucidef_add_switch_attr "switch0" "blinkrate" 2
|
|
ucidef_add_switch_port_attr "switch0" 1 led 6
|
|
ucidef_add_switch_port_attr "switch0" 2 led 9
|
|
ucidef_add_switch_port_attr "switch0" 5 led 2
|
|
;;
|
|
netgear,wnr612-v2|\
|
|
on,n150r)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan" "2:lan" "3:lan:3" "4:lan:4"
|
|
;;
|
|
pcs,cr3000)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
|
|
ucidef_set_interface_wan "eth0"
|
|
;;
|
|
phicomm,k2t)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "3:lan:1" "5:lan:2" "4:wan"
|
|
;;
|
|
tplink,archer-c7-v1|\
|
|
tplink,archer-c7-v2|\
|
|
tplink,tl-wdr4900-v2)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6@eth0" "1:wan"
|
|
;;
|
|
buffalo,whr-g301n|\
|
|
tplink,tl-mr3220-v1|\
|
|
tplink,tl-mr3420-v1|\
|
|
tplink,tl-wr841-v7)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
tplink,tl-wdr3600|\
|
|
tplink,tl-wdr4300)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan:1" "3:lan:2" "4:lan:3" "5:lan:4" "1:wan"
|
|
;;
|
|
tplink,tl-wr1043nd-v1)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
|
|
;;
|
|
tplink,tl-wr1043nd-v2|\
|
|
tplink,tl-wr1043nd-v3)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" "6@eth0"
|
|
;;
|
|
tplink,tl-wr1043nd-v4)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
|
|
;;
|
|
tplink,tl-wr2543-v1)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
|
|
;;
|
|
tplink,tl-wr740n-v1|\
|
|
tplink,tl-wr740n-v3|\
|
|
tplink,tl-wr741-v1|\
|
|
tplink,tl-wr743nd-v1|\
|
|
tplink,tl-wr841-v5|\
|
|
tplink,tl-wr941-v4)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
|
|
;;
|
|
tplink,tl-wr740nd-v4|\
|
|
tplink,tl-wr741nd-v4|\
|
|
tplink,tl-wr841-v9|\
|
|
tplink,tl-wr841-v11)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
tplink,tl-wr941-v2)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
|
|
;;
|
|
ubnt,routerstation)
|
|
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
|
;;
|
|
ubnt,routerstation-pro)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
ubnt,unifiac-mesh-pro|\
|
|
ubnt,unifiac-pro)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan" "3:wan"
|
|
;;
|
|
*)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
ath79_setup_macs()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
avm,fritz300e)
|
|
lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
|
|
;;
|
|
avm,fritz4020)
|
|
lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
|
|
wan_mac=$(fritz_tffs -n macb -i $(find_mtd_part "tffs (1)"))
|
|
;;
|
|
dlink,dir-825-b1)
|
|
lan_mac=$(mtd_get_mac_text "caldata" 65440)
|
|
wan_mac=$(mtd_get_mac_text "caldata" 65460)
|
|
;;
|
|
iodata,etg3-r)
|
|
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
|
wan_mac=$(macaddr_add "$lan_mac" -1)
|
|
;;
|
|
iodata,wn-ac1167dgr|\
|
|
iodata,wn-ac1600dgr2)
|
|
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
|
|
;;
|
|
netgear,wndr3700|\
|
|
netgear,wndr3700v2|\
|
|
netgear,wndr3800)
|
|
lan_mac=$(macaddr_setbit_la "$(mtd_get_mac_binary art 0)")
|
|
;;
|
|
phicomm,k2t)
|
|
lan_mac=$(k2t_get_mac "lan_mac")
|
|
wan_mac=$(k2t_get_mac "wan_mac")
|
|
;;
|
|
tplink,tl-wr1043nd-v4)
|
|
base_mac=$(mtd_get_mac_binary product-info 8)
|
|
wan_mac=$(macaddr_add "$base_mac" 1)
|
|
;;
|
|
tplink,tl-wr941-v2)
|
|
base_mac=$(mtd_get_mac_binary u-boot 130048)
|
|
wan_mac=$(macaddr_add "$base_mac" 1)
|
|
;;
|
|
ubnt,routerstation|\
|
|
ubnt,routerstation-pro)
|
|
wan_mac=$(fconfig -s -r -d $(find_mtd_part "RedBoot config") -n ar7100_esa)
|
|
lan_mac=$(macaddr_add "$wan_mac" 1)
|
|
;;
|
|
wd,mynet-wifi-rangeextender)
|
|
lan_mac=$(nvram get et0macaddr)
|
|
;;
|
|
esac
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
ath79_setup_interfaces $board
|
|
ath79_setup_macs $board
|
|
board_config_flush
|
|
|
|
exit 0
|