openwrtv3/target/linux/gemini/patches-4.14/0012-ARM-dts-Add-ethernet-PHYs-to-the-a-bunch-of-Geminis.patch
Roman Yeryomin 4f74957584 gemini: add 4.14 support
This adds the patches to get fairly complete Gemini support
using kernel v4.14. It is mainly a backport of patches from
kernel v4.16 with omissions of things like graphics that require
substantial changes and will be better handled once we move
to the v4.16 kernel proper.
On top of this are some WIP patches for USB support.

Tested on Raidsonic NAS4220B and D-link DNS-313.

ChangeLog v4->v5:
- Fix ethernet single gmac usecase
- Fix USB reset (patch from Hans)
- Fix Raidsonic ethernet skew delay
- Fix kernel config (bridge, squashfs, jffs2, usb)
- Disable second usb port on Raidsonic board until fotg210_hcd is fixed

ChangeLog v3->v4:
- Make sure to use tabs rather than spaces in base-files.
- Use the dns313 image tool from the firmware-utils.
- Break out the addition of the v4.14 patches and the removal
  of the v4.4 patches to separate (big) patches.

ChangeLog v2->v3:
- Update the kernel config as indicated by Hauke Martens:
- Regenerate again after rebasing using kernel_oldconfig
  dropping a few optimization settings that are now generic
- Drop CFG80211 stuff (module)
- Drop CIFS stuff (module)
- Drop MAC80211 (module)
- Drop wireless drivers (module)
- Enabled OverlayFS
- Added proper DNS-313 boot image generation with the special
  file header tool.
- Disable CMA in the kernel
- Enable LZMA compression of the kernel
- Consequently name the nas4220b images nas4220b
- Update preinit MAC detection script to handle also DNS-313
- Add board.d/03_hdparm to set the disk to spin down after
  1 minute by default, if we have the hdparm tool installed

ChangeLog v1->v2:
- Processed config through kernel_oldconfig
- Processed patches through make target/linux/{clean,refresh} V=99

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00

113 lines
2.7 KiB
Diff

From f0674df220f3da81c173025636a904b395cf8f8b Mon Sep 17 00:00:00 2001
From: Linus Walleij <linus.walleij@linaro.org>
Date: Sun, 19 Nov 2017 10:46:16 +0100
Subject: [PATCH 12/31] ARM: dts: Add ethernet PHYs to the a bunch of Geminis
These Gemini boards have Ethernet PHY on GPIO bit-banged
MDIO, clearly defined in the corresponding OpenWRT
ethernet patches since ages. Add them in accordance with
the OpenWRT patch so we can use them when we add ethernet
support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/gemini-nas4220b.dts | 13 +++++++++++++
arch/arm/boot/dts/gemini-rut1xx.dts | 13 +++++++++++++
arch/arm/boot/dts/gemini-wbd111.dts | 13 +++++++++++++
arch/arm/boot/dts/gemini-wbd222.dts | 18 ++++++++++++++++++
4 files changed, 57 insertions(+)
--- a/arch/arm/boot/dts/gemini-nas4220b.dts
+++ b/arch/arm/boot/dts/gemini-nas4220b.dts
@@ -64,6 +64,19 @@
};
};
+ mdio0: ethernet-phy {
+ compatible = "virtual,mdio-gpio";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
soc {
flash@30000000 {
status = "okay";
--- a/arch/arm/boot/dts/gemini-rut1xx.dts
+++ b/arch/arm/boot/dts/gemini-rut1xx.dts
@@ -58,6 +58,19 @@
};
};
+ mdio0: ethernet-phy {
+ compatible = "virtual,mdio-gpio";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
soc {
flash@30000000 {
status = "okay";
--- a/arch/arm/boot/dts/gemini-wbd111.dts
+++ b/arch/arm/boot/dts/gemini-wbd111.dts
@@ -69,6 +69,19 @@
};
};
+ mdio0: ethernet-phy {
+ compatible = "virtual,mdio-gpio";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
soc {
flash@30000000 {
status = "okay";
--- a/arch/arm/boot/dts/gemini-wbd222.dts
+++ b/arch/arm/boot/dts/gemini-wbd222.dts
@@ -69,6 +69,24 @@
};
};
+ mdio0: ethernet-phy {
+ compatible = "virtual,mdio-gpio";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+
+ phy1: ethernet-phy@3 {
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ };
+
soc {
flash@30000000 {
status = "okay";