KumiSystems/openwrtv3
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity
openwrtv3/target/linux/ramips/image/mt7620.mk
Andrew Crawley fe6f298b07 ramips: add support for Vonets VAR11N-300 
The VAR11N-300 is a tiny wireless-N device with a hardwired Ethernet
cable, one extra Ethernet port, and an internal antenna, based on the
MediaTek MT7620n chipset.

Specs:
- MT7620n WiSoC @ 600MHz
- 32 MB SDRAM
- 4 MB SPI flash
- 2T2R 2.4GHz WiFi-N
- 1 attached 10/100 Ethernet cable (LAN)
- 1 10/100 Ethernet port (WAN)
- 1 attached USB / barrel 5vdc power cable
- 5 LEDs (see notes below)
- 1 reset button
- 1 UART (3 pads on board)

Installation:

The stock firmware does not support uploading new firmware directly,
only checking the manufacturer's site for updates.  This process may be
possible to spoof, but the update check uses some kind of homebrew
encryption that I didn't investigate.  Instead, you can install via a
backdoor:

1. Set up a TFTP server to serve the firmware binary
(lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin)
2. Factory reset the device by holding the reset button for a few
seconds.
3. Open the web interface (default IP: 192.168.253.254)
4. Log in with the "super admin" credentials: username `vonets`,
password `vonets26642519`.
5. On the "Operative Status" page, click the text "System Uptime", then
quickly click the uptime value.
6. If successful, an alert dialog will appear reading "Ated start", and
the device will now accept telnet connections.  If the alert does not
appear, repeat step 5 until it works (the timing is a bit tricky).
7. Telnet to the device using credentials "admin / admin"
8. Retrieve the firmware binary from the tftp server: `tftp -l lede.bin
-r lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin -g
<tftp-server-ip>`
9. Write the firmware to flash: `mtd_write write lede.bin /dev/mtd4`
10. Reboot

Tested:
- LAN / WAN ethernet
- WiFi
- LAN / WAN / status LED GPIOs (see notes below)
- Reset button
- Sysupgrade

Notes:

LEDs:

The board has 5 LEDs - two green LEDs for LAN / WAN activity, one blue
LED for WiFi, and a pair of "status" LEDs connected to the same GPIO
(the blue LED lights when the GPIO is low, and the green when it's
high).  I was unable to determine how to operate the WiFi LED, as it
does not appear to be controlled by a GPIO directly.

Recovery:

The default U-boot installation will only boot from flash due to a
missing environment block.  I generated a valid 4KB env block using
U-boot's `fw_setenv` tool and wrote it to flash at 0x30000 using an
external programmer.  After this, it was possible to enter the U-boot
commandline interface and download a new image via TFTP (`tftpboot
81b00000 <image-filename>`), but while I could boot this image
sucessfully (`bootm`), writing it to flash (`cp.linux`) just corrupted
the flash chip.  The sysupgrade file can be written to flash at 0x50000
using an external programmer.

Signed-off-by: Andrew Crawley <acrawley@gmail.com>
2017-12-21 01:05:16 +01:00

600 lines
15 KiB
Makefile
Raw Blame History

#
# MT7620A Profiles
#
DEVICE_VARS += TPLINK_FLASHLAYOUT TPLINK_HWID TPLINK_HWREV TPLINK_HWREVADD TPLINK_HVERSION
define Build/elecom-header
cp $@ $(KDIR)/v_0.0.0.bin
( \
mkhash md5 $(KDIR)/v_0.0.0.bin && \
echo 458 \
) | mkhash md5 > $(KDIR)/v_0.0.0.md5
$(STAGING_DIR_HOST)/bin/tar -c \
$(if $(SOURCE_DATE_EPOCH),--mtime=@$(SOURCE_DATE_EPOCH)) \
-f $@ -C $(KDIR) v_0.0.0.bin v_0.0.0.md5
endef
define Build/zyimage
$(STAGING_DIR_HOST)/bin/zyimage $(1) $@
endef
define Device/ai-br100
DTS := AI-BR100
IMAGE_SIZE := 7936k
DEVICE_TITLE := Aigale Ai-BR100
DEVICE_PACKAGES:= kmod-usb2 kmod-usb-ohci
endef
TARGET_DEVICES += ai-br100
define Device/Archer
TPLINK_HWREVADD := 0
TPLINK_HVERSION := 3
KERNEL := $(KERNEL_DTB)
KERNEL_INITRAMFS := $(KERNEL_DTB) | tplink-v2-header -e
IMAGE/factory.bin := tplink-v2-image -e
IMAGE/sysupgrade.bin := tplink-v2-image -s -e | append-metadata
endef
define Device/ArcherC20
$(Device/Archer)
DTS := ArcherC20
SUPPORTED_DEVICES := c20
TPLINK_FLASHLAYOUT := 8Mmtk
TPLINK_HWID := 0xc2000001
TPLINK_HWREV := 0x44
TPLINK_HWREVADD := 0x1
IMAGES += factory.bin
DEVICE_TITLE := TP-Link ArcherC20
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += ArcherC20
define Device/ArcherC20i
$(Device/Archer)
DTS := ArcherC20i
SUPPORTED_DEVICES := c20i
TPLINK_FLASHLAYOUT := 8Mmtk
TPLINK_HWID := 0xc2000001
TPLINK_HWREV := 58
IMAGES += factory.bin
DEVICE_TITLE := TP-Link ArcherC20i
endef
TARGET_DEVICES += ArcherC20i
define Device/ArcherC50v1
$(Device/Archer)
DTS := ArcherC50
SUPPORTED_DEVICES := c50
TPLINK_FLASHLAYOUT := 8Mmtk
TPLINK_HWID := 0xc7500001
TPLINK_HWREV := 69
IMAGES += factory-us.bin factory-eu.bin
IMAGE/factory-us.bin := tplink-v2-image -e -w 0
IMAGE/factory-eu.bin := tplink-v2-image -e -w 2
DEVICE_TITLE := TP-Link ArcherC50v1
endef
TARGET_DEVICES += ArcherC50v1
define Device/ArcherMR200
$(Device/Archer)
DTS := ArcherMR200
SUPPORTED_DEVICES := mr200
TPLINK_FLASHLAYOUT := 8MLmtk
TPLINK_HWID := 0xd7500001
TPLINK_HWREV := 0x4a
DEVICE_PACKAGES := kmod-usb2 kmod-usb-net kmod-usb-net-rndis kmod-usb-serial kmod-usb-serial-option adb-enablemodem
DEVICE_TITLE := TP-Link ArcherMR200
endef
TARGET_DEVICES += ArcherMR200
define Device/c108
DTS := C108
IMAGE_SIZE := 16777216
DEVICE_TITLE := HNET C108
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-sdhci-mt7620
endef
TARGET_DEVICES += c108
define Device/cf-wr800n
DTS := CF-WR800N
DEVICE_TITLE := Comfast CF-WR800N
endef
TARGET_DEVICES += cf-wr800n
define Device/cs-qr10
DTS := CS-QR10
DEVICE_TITLE := Planex CS-QR10
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci \
kmod-sound-core kmod-sound-mt7620 \
kmod-i2c-ralink kmod-sdhci-mt7620
endef
TARGET_DEVICES += cs-qr10
define Device/d240
DTS := D240
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := Sanlinking Technologies D240
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-mt76-core kmod-mt76x2 kmod-sdhci-mt7620
endef
TARGET_DEVICES += d240
define Device/db-wrt01
DTS := DB-WRT01
DEVICE_TITLE := Planex DB-WRT01
endef
TARGET_DEVICES += db-wrt01
define Device/dch-m225
DTS := DCH-M225
BLOCKSIZE := 4k
IMAGES += factory.bin
IMAGE_SIZE := 6848k
IMAGE/sysupgrade.bin := \
append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs | \
seama -m "dev=/dev/mtdblock/2" -m "type=firmware" | \
pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
IMAGE/factory.bin := \
append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
append-rootfs | pad-rootfs -x 64 | \
seama -m "dev=/dev/mtdblock/2" -m "type=firmware" | \
seama-seal -m "signature=wapn22_dlink.2013gui_dap1320b" | \
check-size $$$$(IMAGE_SIZE)
DEVICE_TITLE := D-Link DCH-M225
DEVICE_PACKAGES := kmod-mt76 kmod-sound-core kmod-sound-mt7620 kmod-i2c-ralink
endef
TARGET_DEVICES += dch-m225
define Device/dir-810l
DTS := DIR-810L
IMAGE_SIZE := 6720k
DEVICE_TITLE := D-Link DIR-810L
endef
TARGET_DEVICES += dir-810l
define Device/e1700
DTS := E1700
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) | \
umedia-header 0x013326
DEVICE_TITLE := Linksys E1700
endef
TARGET_DEVICES += e1700
define Device/ex2700
NETGEAR_HW_ID := 29764623+4+0+32+2x2+0
NETGEAR_BOARD_ID := EX2700
DTS := EX2700
BLOCKSIZE := 4k
IMAGE_SIZE := $(ralink_default_fw_size_4M)
IMAGES += factory.bin
KERNEL := $(KERNEL_DTB) | uImage lzma | pad-offset 64k 64 | append-uImage-fakeroot-hdr
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) | \
netgear-dni
DEVICE_PACKAGES := -kmod-mt76
DEVICE_TITLE := Netgear EX2700
endef
TARGET_DEVICES += ex2700
define Device/ex3700-ex3800
NETGEAR_BOARD_ID := U12H319T00_NETGEAR
DTS := EX3700
BLOCKSIZE := 4k
IMAGE_SIZE := 7744k
IMAGES += factory.chk
IMAGE/factory.chk := $$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) | netgear-chk
DEVICE_PACKAGES := -kmod-mt76 kmod-mt76x2
DEVICE_TITLE := Netgear EX3700/EX3800
SUPPORTED_DEVICES := ex3700
endef
TARGET_DEVICES += ex3700-ex3800
define Device/gl-mt300a
DTS := GL-MT300A
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := GL-Inet GL-MT300A
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-mt76
endef
TARGET_DEVICES += gl-mt300a
define Device/u25awf-h1
DTS := U25AWF-H1
IMAGE_SIZE := 16064k
DEVICE_TITLE := Kimax U25AWF-H1
endef
TARGET_DEVICES += u25awf-h1
define Device/gl-mt300n
DTS := GL-MT300N
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := GL-Inet GL-MT300N
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-mt76
endef
TARGET_DEVICES += gl-mt300n
define Device/gl-mt750
DTS := GL-MT750
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := GL-Inet GL-MT750
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-mt76
endef
TARGET_DEVICES += gl-mt750
define Device/hc5661
DTS := HC5661
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := HiWiFi HC5661
DEVICE_PACKAGES := kmod-usb2 kmod-sdhci-mt7620 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += hc5661
define Device/hc5761
DTS := HC5761
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := HiWiFi HC5761
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-sdhci-mt7620 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += hc5761
define Device/hc5861
DTS := HC5861
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := HiWiFi HC5861
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-sdhci-mt7620 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += hc5861
define Device/kng_rc
DTS := kng_rc
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := ZyXEL Keenetic Viva
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport kmod-switch-rtl8366-smi kmod-switch-rtl8367b
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | pad-to 64k | check-size $$$$(IMAGE_SIZE) | \
zyimage -d 8997 -v "ZyXEL Keenetic Viva"
SUPPORTED_DEVICES := kng_rc
endef
TARGET_DEVICES += kng_rc
define Device/kn_rc
DTS := kn_rc
DEVICE_TITLE := ZyXEL Keenetic Omni
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport
IMAGES += factory.bin
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | pad-to 64k | check-size $$$$(IMAGE_SIZE) | \
zyimage -d 4882 -v "ZyXEL Keenetic Omni"
SUPPORTED_DEVICES := kn_rc
endef
TARGET_DEVICES += kn_rc
define Device/kn_rf
DTS := kn_rf
DEVICE_TITLE := ZyXEL Keenetic Omni II
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport
IMAGES += factory.bin
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | pad-to 64k | check-size $$$$(IMAGE_SIZE) | \
zyimage -d 2102034 -v "ZyXEL Keenetic Omni II"
SUPPORTED_DEVICES := kn_rf
endef
TARGET_DEVICES += kn_rf
define Device/microwrt
DTS := MicroWRT
IMAGE_SIZE := 16128k
DEVICE_TITLE := Microduino MicroWRT
endef
TARGET_DEVICES += microwrt
define Device/miwifi-mini
DTS := MIWIFI-MINI
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := Xiaomi MiWiFi Mini
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
endef
TARGET_DEVICES += miwifi-mini
define Device/mlw221
DTS := MLW221
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := Kingston MLW221
endef
TARGET_DEVICES += mlw221
define Device/mlwg2
DTS := MLWG2
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := Kingston MLWG2
endef
TARGET_DEVICES += mlwg2
define Device/mt7620a
DTS := MT7620a
DEVICE_TITLE := MediaTek MT7620a EVB
endef
TARGET_DEVICES += mt7620a
define Device/mt7620a_mt7530
DTS := MT7620a_MT7530
DEVICE_TITLE := MediaTek MT7620a + MT7530 EVB
SUPPORTED_DEVICES := mt7620a_mt7530
endef
TARGET_DEVICES += mt7620a_mt7530
define Device/mt7620a_mt7610e
DTS := MT7620a_MT7610e
DEVICE_TITLE := MediaTek MT7620a + MT7610e EVB
SUPPORTED_DEVICES := mt7620a_mt7610e
endef
TARGET_DEVICES += mt7620a_mt7610e
define Device/mt7620a_v22sg
DTS := MT7620a_V22SG
DEVICE_TITLE := MediaTek MT7620a V22SG
SUPPORTED_DEVICES := mt7620a_v22sg
endef
TARGET_DEVICES += mt7620a_v22sg
define Device/mzk-750dhp
DTS := MZK-750DHP
DEVICE_TITLE := Planex MZK-750DHP
DEVICE_PACKAGES := kmod-mt76
endef
TARGET_DEVICES += mzk-750dhp
define Device/mzk-ex300np
DTS := MZK-EX300NP
DEVICE_TITLE := Planex MZK-EX300NP
endef
TARGET_DEVICES += mzk-ex300np
define Device/mzk-ex750np
DTS := MZK-EX750NP
DEVICE_TITLE := Planex MZK-EX750NP
DEVICE_PACKAGES := kmod-mt76
endef
TARGET_DEVICES += mzk-ex750np
define Device/na930
DTS := NA930
IMAGE_SIZE := 20m
DEVICE_TITLE := Sercomm NA930
endef
TARGET_DEVICES += na930
define Device/oy-0001
DTS := OY-0001
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := Oh Yeah OY-0001
endef
TARGET_DEVICES += oy-0001
define Device/psg1208
DTS := PSG1208
DEVICE_TITLE := Phicomm PSG1208
DEVICE_PACKAGES := kmod-mt76
endef
TARGET_DEVICES += psg1208
define Device/psg1218a
DTS := PSG1218A
DEVICE_TITLE := Phicomm PSG1218 rev.Ax
DEVICE_PACKAGES := kmod-mt76x2
SUPPORTED_DEVICES += psg1218
endef
TARGET_DEVICES += psg1218a
define Device/psg1218b
DTS := PSG1218B
DEVICE_TITLE := Phicomm PSG1218 rev.Bx
DEVICE_PACKAGES := kmod-mt76x2
SUPPORTED_DEVICES += psg1218
endef
TARGET_DEVICES += psg1218b
define Device/rp-n53
DTS := RP-N53
DEVICE_TITLE := Asus RP-N53
endef
TARGET_DEVICES += rp-n53
define Device/rt-n12p
DTS := RT-N12-PLUS
DEVICE_TITLE := Asus RT-N11P/RT-N12+/RT-N12Eb1
endef
TARGET_DEVICES += rt-n12p
define Device/rt-n14u
DTS := RT-N14U
DEVICE_TITLE := Asus RT-N14u
endef
TARGET_DEVICES += rt-n14u
define Device/rt-ac51u
DTS := RT-AC51U
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := Asus RT-AC51U
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ehci kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += rt-ac51u
define Device/tiny-ac
DTS := TINY-AC
DEVICE_TITLE := Dovado Tiny AC
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
endef
TARGET_DEVICES += tiny-ac
define Device/vonets_var11n-300
DTS := VAR11N-300
IMAGE_SIZE := $(ralink_default_fw_size_4M)
BLOCKSIZE := 4k
DEVICE_TITLE := Vonets VAR11N-300
endef
TARGET_DEVICES += vonets_var11n-300
define Device/whr-1166d
DTS := WHR-1166D
IMAGE_SIZE := 15040k
DEVICE_TITLE := Buffalo WHR-1166D
endef
TARGET_DEVICES += whr-1166d
define Device/whr-300hp2
DTS := WHR-300HP2
IMAGE_SIZE := 6848k
DEVICE_TITLE := Buffalo WHR-300HP2
endef
TARGET_DEVICES += whr-300hp2
define Device/whr-600d
DTS := WHR-600D
IMAGE_SIZE := 6848k
DEVICE_TITLE := Buffalo WHR-600D
endef
TARGET_DEVICES += whr-600d
define Device/wmr-300
DTS := WMR-300
DEVICE_TITLE := Buffalo WMR-300
endef
TARGET_DEVICES += wmr-300
define Device/wn3000rpv3
NETGEAR_HW_ID := 29764836+8+0+32+2x2+0
NETGEAR_BOARD_ID := WN3000RPv3
DTS := WN3000RPV3
BLOCKSIZE := 4k
IMAGES += factory.bin
KERNEL := $(KERNEL_DTB) | uImage lzma | pad-offset 64k 64 | append-uImage-fakeroot-hdr
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) | \
netgear-dni
DEVICE_TITLE := Netgear WN3000RPv3
endef
TARGET_DEVICES += wn3000rpv3
define Device/wrh-300cr
DTS := WRH-300CR
IMAGE_SIZE := $(ralink_default_fw_size_16M)
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) | \
elecom-header
DEVICE_TITLE := Elecom WRH-300CR
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
endef
TARGET_DEVICES += wrh-300cr
define Device/wrtnode
DTS := WRTNODE
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := WRTNode
endef
TARGET_DEVICES += wrtnode
define Device/wt3020-4M
DTS := WT3020-4M
BLOCKSIZE := 4k
IMAGE_SIZE := $(ralink_default_fw_size_4M)
IMAGES += factory.bin
SUPPORTED_DEVICES += wt3020
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) | \
poray-header -B WT3020 -F 4M
DEVICE_TITLE := Nexx WT3020 (4MB)
endef
TARGET_DEVICES += wt3020-4M
define Device/wt3020-8M
DTS := WT3020-8M
IMAGES += factory.bin
SUPPORTED_DEVICES += wt3020
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) | \
poray-header -B WT3020 -F 8M
DEVICE_TITLE := Nexx WT3020 (8MB)
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
endef
TARGET_DEVICES += wt3020-8M
define Device/y1
DTS := Y1
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := Lenovo Y1
endef
TARGET_DEVICES += y1
define Device/y1s
DTS := Y1S
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := Lenovo Y1S
endef
TARGET_DEVICES += y1s
define Device/youku-yk1
DTS := YOUKU-YK1
IMAGE_SIZE := $(ralink_default_fw_size_32M)
DEVICE_TITLE := YOUKU YK1
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-sdhci-mt7620 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += youku-yk1
define Device/we1026-5g-16m
DTS := WE1026-5G-16M
IMAGE_SIZE := 16777216
SUPPORTED_DEVICES += we1026-5g-16m
DEVICE_TITLE := Zbtlink ZBT-WE1026-5G (16M)
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-mt76 kmod-sdhci-mt7620
endef
TARGET_DEVICES += we1026-5g-16m
define Device/zbt-ape522ii
DTS := ZBT-APE522II
DEVICE_TITLE := Zbtlink ZBT-APE522II
DEVICE_PACKAGES := kmod-mt76
endef
TARGET_DEVICES += zbt-ape522ii
define Device/zbt-cpe102
DTS := ZBT-CPE102
DEVICE_TITLE := Zbtlink ZBT-CPE102
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
endef
TARGET_DEVICES += zbt-cpe102
define Device/zbt-wa05
DTS := ZBT-WA05
DEVICE_TITLE := Zbtlink ZBT-WA05
endef
TARGET_DEVICES += zbt-wa05
define Device/zbt-we2026
DTS := ZBT-WE2026
DEVICE_TITLE := Zbtlink ZBT-WE2026
endef
TARGET_DEVICES += zbt-we2026
define Device/zbt-we826-16M
DTS := ZBT-WE826-16M
IMAGE_SIZE := $(ralink_default_fw_size_16M)
SUPPORTED_DEVICES += zbt-we826
DEVICE_TITLE := Zbtlink ZBT-WE826 (16M)
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-mt76 kmod-sdhci-mt7620
endef
TARGET_DEVICES += zbt-we826-16M
define Device/zbt-we826-32M
DTS := ZBT-WE826-32M
IMAGE_SIZE := $(ralink_default_fw_size_32M)
DEVICE_TITLE := Zbtlink ZBT-WE826 (32M)
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-mt76 kmod-sdhci-mt7620
endef
TARGET_DEVICES += zbt-we826-32M
define Device/zbt-wr8305rt
DTS := ZBT-WR8305RT
DEVICE_TITLE := Zbtlink ZBT-WR8305RT
endef
TARGET_DEVICES += zbt-wr8305rt
define Device/zte-q7
DTS := ZTE-Q7
DEVICE_TITLE := ZTE Q7
endef
TARGET_DEVICES += zte-q7
Reference in a new issue View git blame Copy permalink