6525bffc0a
The DWR-921-C1 Wireless Routers with LTE embedded modem is based on the
MT7620N SoC.
Specification:
* MediaTek MT7620N (580 Mhz)
* 64 MB of RAM
* 16 MB of FLASH
* 802.11bgn radio
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* 2x external, detachable (LTE) antennas
* UART header on PCB (57600 8n1)
* 6x LED (GPIO-controlled)
* 1x bi-color Signal Strength LED (GPIO-controlled)
* 2x button
* JBOOT bootloader
The status led has been assigned to the dwr-921-c1:green:sigstrength (lte
signal strength) led. At the end of the boot it is switched off and is
available for lte operation. Work correctly also during sysupgrade
operation.
Installation:
Apply factory image via d-link http web-gui.
How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.bin http://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
74 lines
1.6 KiB
Bash
74 lines
1.6 KiB
Bash
#!/bin/sh
|
|
|
|
rt2x00_eeprom_die() {
|
|
echo "rt2x00 eeprom: " "$*"
|
|
exit 1
|
|
}
|
|
|
|
rt2x00_eeprom_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local mtd
|
|
|
|
mtd=$(find_mtd_part $part)
|
|
[ -n "$mtd" ] || \
|
|
rt2x00_eeprom_die "no mtd device found for partition $part"
|
|
|
|
dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
|
|
rt2x00_eeprom_die "failed to extract from $mtd"
|
|
}
|
|
|
|
jboot_eeprom_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local mtd
|
|
|
|
mtd=$(find_mtd_part $part)
|
|
[ -n "$mtd" ] || \
|
|
rt2x00_eeprom_die "no mtd device found for partition $part"
|
|
|
|
jboot_config_read -i $mtd -o $offset -e /lib/firmware/$FIRMWARE 2>/dev/null || \
|
|
rt2x00_eeprom_die "failed to extract from $mtd"
|
|
}
|
|
|
|
rt2x00_eeprom_set_macaddr() {
|
|
local macaddr=$1
|
|
|
|
[ -n "$macaddr" ] || \
|
|
rt2x00_eeprom_die "invalid wlan mac address"
|
|
|
|
macaddr_2bin $macaddr | dd of=/lib/firmware/$FIRMWARE \
|
|
conv=notrunc bs=1 seek=4 count=6 2>/dev/null || \
|
|
rt2x00_eeprom_die "failed to write mac address to eeprom file"
|
|
}
|
|
|
|
FW="/lib/firmware/$FIRMWARE"
|
|
[ -e "$FW" ] && exit 0
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/system.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$FIRMWARE" in
|
|
"soc_wmac.eeprom")
|
|
case $board in
|
|
dlink,dwr-116-a1|\
|
|
dlink,dwr-921-c1)
|
|
wan_mac=$(jboot_config_read -m -i $(find_mtd_part "config") -o 0xE000)
|
|
wifi_mac=$(macaddr_add "$wan_mac" 1)
|
|
jboot_eeprom_extract "config" 0xE000
|
|
rt2x00_eeprom_set_macaddr $wifi_mac
|
|
;;
|
|
tiny-ac)
|
|
wifi_mac=$(mtd_get_mac_ascii u-boot-env INIC_MAC_ADDR)
|
|
rt2x00_eeprom_extract "factory" 0 512
|
|
rt2x00_eeprom_set_macaddr $wifi_mac
|
|
;;
|
|
*)
|
|
rt2x00_eeprom_die "Please define mtd-eeprom in $board DTS file!"
|
|
;;
|
|
esac
|
|
;;
|
|
esac
|