KumiSystems/openwrtv3
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity
openwrtv3/target/linux/ramips/image/mt7621.mk
Tobias Schramm 5684d08741 ramips: Add support for Mikrotik RouterBOARD RBM33g 
This commit adds support for the Mikrotik RouterBOARD RBM33g.

=Hardware=

The RBM33g is a mt7621 based device featuring three gigabit ports, 2
miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male
onboard RS-232 serial port. Additionally there are a lot of accessible
GPIO ports and additional buses like i2c, mdio, spi and uart.

==Switch==

The three Ethernet ports are all connected to the internal switch of the
mt7621 SoC:

port 0: Ethernet Port next to barrel jack with PoE printed on it
port 1: Innermost Ethernet Port on opposite side of RS-232 port
port 2: Outermost Ethernet Port on opposite side of RS-232 port
port 6: CPU

==Flash==

The device has two spi flash chips. The first flash chips is rather small
(512 kB), connected to CS0 by default and contains only the RouterBOOT
bootloader and some factory information (e.g. mac address).
The second chip has a size of 16 MB, is by default connected to CS1 and
contains the firmware image.

==PCIe==

The board features three PCIe-enabled slots. Two of them are miniPCIe
slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2).
Each of the miniPCIe slots is connected to a dedicated mini SIM socket
on the back of the board.

Power to all three PCIe-enabled slots is controlled via GPIOs on the
mt7621 SoC:

PCIe0: GPIO9
PCIe1: GPIO10
PCIe2: GPIO11

==USB==

The board has one external USB 3.0 port at the rear. Additionally PCIe
port 0 has a permanently enabled USB interface. PCIe slot 1 shares its
USB interface with the rear USB port. Thus only either the rear USB port
or the USB interface of PCIe slot 1 can be active at the same time. The
jumper next to the rear USB port controls which one is active:

open: USB on PCIe 1 is active
closed: USB on rear USB port is active

==Power==

The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack. The input voltage range is 11-32 V.

=Installation=

==Prerequisites==

A USB -> RS-232 Adapter and a null modem cable are required for
installation.

To install an OpenWRT image to the device two components must be built:

1. A openwrt initramfs image
2. A openwrt sysupgrade image

===initramfs & sysupgrade image===

Select target devices "Mikrotik RBM33G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output
directory.

==Installing==

**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the created
license file.**

Serial settings: 115200 8N1

The installation is a two-step process. First the
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted
via tftp:

1. Set up a dhcp server that points the bootfile to tftp server serving
   the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin"
   initramfs image
2. Connect to WAN port (left side, next to sys-LED and power indicator)
3. Connect to serial port of board
4. Power on board and enter RouterBOOT setup menu
5. Set boot device to "boot over ethernet"
6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server
   allows dynamic bootp)
6. Save config
7. Wait for board to boot via Ethernet

On the serial port you should now be presented with the OpenWRT boot log.
The next steps will install OpenWRT persistently.

1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device
   using scp.
2. Write openwrt to flash using "sysupgrade
   openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin"

Once the flashing completes reboot the router and let it boot from flash.
It should boot straight to OpenWRT.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:54:42 +02:00

469 lines
14 KiB
Makefile
Raw Blame History

#
# MT7621 Profiles
#
DEVICE_VARS += TPLINK_BOARD_ID TPLINK_HEADER_VERSION TPLINK_HWID TPLINK_HWREV
define Build/elecom-wrc-factory
$(eval product=$(word 1,$(1)))
$(eval version=$(word 2,$(1)))
$(STAGING_DIR_HOST)/bin/mkhash md5 $@ >> $@
( \
echo -n "ELECOM $(product) v$(version)" | \
dd bs=32 count=1 conv=sync; \
dd if=$@; \
) > $@.new
mv $@.new $@
endef
define Build/ubnt-erx-factory-image
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(KERNEL_SIZE)" ]; then \
echo '21001:6' > $(1).compat; \
$(TAR) -cf $(1) --transform='s/^.*/compat/' $(1).compat; \
\
$(TAR) -rf $(1) --transform='s/^.*/vmlinux.tmp/' $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE); \
mkhash md5 $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) > $(1).md5; \
$(TAR) -rf $(1) --transform='s/^.*/vmlinux.tmp.md5/' $(1).md5; \
\
echo "dummy" > $(1).rootfs; \
$(TAR) -rf $(1) --transform='s/^.*/squashfs.tmp/' $(1).rootfs; \
\
mkhash md5 $(1).rootfs > $(1).md5; \
$(TAR) -rf $(1) --transform='s/^.*/squashfs.tmp.md5/' $(1).md5; \
\
echo '$(BOARD) $(VERSION_CODE) $(VERSION_NUMBER)' > $(1).version; \
$(TAR) -rf $(1) --transform='s/^.*/version.tmp/' $(1).version; \
\
$(CP) $(1) $(BIN_DIR)/; \
else \
echo "WARNING: initramfs kernel image too big, cannot generate factory image" >&2; \
fi
endef
define Device/11acnas
DTS := 11ACNAS
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := WeVO 11AC NAS Router
DEVICE_PACKAGES := kmod-mt7603 kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += 11acnas
define Device/dir-860l-b1
DTS := DIR-860L-B1
BLOCKSIZE := 64k
IMAGES += factory.bin
KERNEL := kernel-bin | patch-dtb | relocate-kernel | lzma | uImage lzma
IMAGE_SIZE := $(ralink_default_fw_size_16M)
IMAGE/sysupgrade.bin := \
append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs | \
seama -m "dev=/dev/mtdblock/2" -m "type=firmware" | \
pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
IMAGE/factory.bin := \
append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
append-rootfs | pad-rootfs -x 64 | \
seama -m "dev=/dev/mtdblock/2" -m "type=firmware" | \
seama-seal -m "signature=wrgac13_dlink.2013gui_dir860lb" | \
check-size $$$$(IMAGE_SIZE)
DEVICE_TITLE := D-Link DIR-860L B1
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += dir-860l-b1
define Device/mediatek_ap-mt7621a-v60
DTS := AP-MT7621A-V60
IMAGE_SIZE := $(ralink_default_fw_size_8M)
DEVICE_TITLE := Mediatek AP-MT7621A-V60 EVB
DEVICE_PACKAGES := kmod-usb3 kmod-sdhci-mt7620 kmod-sound-mt7620
endef
TARGET_DEVICES += mediatek_ap-mt7621a-v60
define Device/elecom_wrc-1167ghbk2-s
DTS := WRC-1167GHBK2-S
IMAGE_SIZE := 15488k
DEVICE_TITLE := ELECOM WRC-1167GHBK2-S
IMAGES += factory.bin
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) |\
elecom-wrc-factory WRC-1167GHBK2-S 0.00
endef
TARGET_DEVICES += elecom_wrc-1167ghbk2-s
define Device/ew1200
DTS := EW1200
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := AFOUNDRY EW1200
DEVICE_PACKAGES := \
kmod-ata-core kmod-ata-ahci kmod-mt76x2 kmod-mt7603 kmod-usb3 \
kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += ew1200
define Device/firewrt
DTS := FIREWRT
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := Firefly FireWRT
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += firewrt
define Device/gnubee_gb-pc1
DTS := GB-PC1
DEVICE_TITLE := GnuBee Personal Cloud One
DEVICE_PACKAGES := kmod-ata-core kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620
IMAGE_SIZE := $(ralink_default_fw_size_32M)
endef
TARGET_DEVICES += gnubee_gb-pc1
define Device/gnubee_gb-pc2
DTS := GB-PC2
DEVICE_TITLE := GnuBee Personal Cloud Two
DEVICE_PACKAGES := kmod-ata-core kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620
IMAGE_SIZE := $(ralink_default_fw_size_32M)
endef
TARGET_DEVICES += gnubee_gb-pc2
define Device/hc5962
DTS := HC5962
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 2097152
UBINIZE_OPTS := -E 5
IMAGE_SIZE := $(ralink_default_fw_size_32M)
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | check-size $$$$(IMAGE_SIZE)
DEVICE_TITLE := HiWiFi HC5962
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 wpad-mini
endef
TARGET_DEVICES += hc5962
define Device/iodata_wn-gx300gr
DTS := WN-GX300GR
IMAGE_SIZE := 7798784
DEVICE_TITLE := I-O DATA WN-GX300GR
DEVICE_PACKAGES := kmod-mt7603 wpad-mini
endef
TARGET_DEVICES += iodata_wn-gx300gr
define Device/k2p
DTS := K2P
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := Phicomm K2P
endef
TARGET_DEVICES += k2p
define Device/mir3g
DTS := MIR3G
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
KERNEL := $(KERNEL_DTB) | uImage lzma
IMAGE_SIZE := 32768k
UBINIZE_OPTS := -E 5
IMAGES := sysupgrade.tar kernel1.bin rootfs0.bin
IMAGE/kernel1.bin := append-kernel
IMAGE/rootfs0.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
DEVICE_TITLE := Xiaomi Mi Router 3G
SUPPORTED_DEVICES += R3G
DEVICE_PACKAGES := \
kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini \
uboot-envtools
endef
TARGET_DEVICES += mir3g
define Device/mt7621
DTS := MT7621
BLOCKSIZE := 64k
IMAGE_SIZE := $(ralink_default_fw_size_4M)
DEVICE_TITLE := MediaTek MT7621 EVB
endef
TARGET_DEVICES += mt7621
define Device/newifi-d1
DTS := Newifi-D1
IMAGE_SIZE := $(ralink_default_fw_size_32M)
DEVICE_TITLE := Newifi D1
DEVICE_PACKAGES := \
kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += newifi-d1
define Device/d-team_newifi-d2
DTS := Newifi-D2
IMAGE_SIZE := $(ralink_default_fw_size_32M)
DEVICE_TITLE := Newifi D2
DEVICE_PACKAGES := \
kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += d-team_newifi-d2
define Device/pbr-m1
DTS := PBR-M1
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := PBR-M1
DEVICE_PACKAGES := \
kmod-ata-core kmod-ata-ahci kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += pbr-m1
define Device/r6220
DTS := R6220
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
KERNEL := $(KERNEL_DTB) | uImage lzma
IMAGE_SIZE := 28672k
UBINIZE_OPTS := -E 5
IMAGES := sysupgrade.tar kernel.bin rootfs.bin
IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
IMAGE/kernel.bin := append-kernel
IMAGE/rootfs.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
DEVICE_TITLE := Netgear R6220
DEVICE_PACKAGES := \
kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += r6220
define Device/rb750gr3
DTS := RB750Gr3
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := MikroTik RB750Gr3
DEVICE_PACKAGES := kmod-usb3 uboot-envtools
endef
TARGET_DEVICES += rb750gr3
define Device/mikrotik_rbm33g
DTS := RBM33G
BLOCKSIZE := 64k
IMAGE_SIZE := 16128k
DEVICE_TITLE := MikroTik RBM33G
DEVICE_PACKAGES := kmod-usb3
LOADER_TYPE := elf
PLATFORM := mt7621
KERNEL := kernel-bin | patch-dtb | lzma | loader-kernel
IMAGE/sysupgrade.bin := append-kernel | kernel2minor -s 1024 | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
endef
TARGET_DEVICES += mikrotik_rbm33g
define Device/re350-v1
DTS := RE350
DEVICE_TITLE := TP-LINK RE350 v1
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 wpad-mini
TPLINK_BOARD_ID := RE350-V1
TPLINK_HWID := 0x0
TPLINK_HWREV := 0
TPLINK_HEADER_VERSION := 1
IMAGE_SIZE := 6016k
KERNEL := $(KERNEL_DTB) | tplink-v1-header -e
IMAGES := sysupgrade.bin factory.bin
IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | append-metadata | check-size $$$$(IMAGE_SIZE)
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
endef
TARGET_DEVICES += re350-v1
define Device/re6500
DTS := RE6500
DEVICE_TITLE := Linksys RE6500
DEVICE_PACKAGES := kmod-mt76x2 wpad-mini
endef
TARGET_DEVICES += re6500
define Device/sap-g3200u3
DTS := SAP-G3200U3
DEVICE_TITLE := STORYLiNK SAP-G3200U3
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += sap-g3200u3
define Device/sk-wb8
DTS := SK-WB8
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := SamKnows Whitebox 8
DEVICE_PACKAGES := \
kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport \
uboot-envtools wpad-mini
endef
TARGET_DEVICES += sk-wb8
define Device/timecloud
DTS := Timecloud
DEVICE_TITLE := Thunder Timecloud
DEVICE_PACKAGES := kmod-usb3
endef
TARGET_DEVICES += timecloud
define Device/u7621-06-256M-16M
DTS := U7621-06-256M-16M
IMAGE_SIZE := 16064k
DEVICE_TITLE := UniElec U7621-06 (256M RAM/16M flash)
DEVICE_PACKAGES := kmod-ata-core kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3
endef
TARGET_DEVICES += u7621-06-256M-16M
define Device/ubnt-erx
DTS := UBNT-ERX
FILESYSTEMS := squashfs
KERNEL_SIZE := 3145728
KERNEL := $(KERNEL_DTB) | uImage lzma
IMAGES := sysupgrade.tar
KERNEL_INITRAMFS := $$(KERNEL) | ubnt-erx-factory-image $(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.tar
IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
DEVICE_TITLE := Ubiquiti EdgeRouter X
endef
TARGET_DEVICES += ubnt-erx
define Device/ubnt-erx-sfp
$(Device/ubnt-erx)
DTS := UBNT-ERX-SFP
DEVICE_TITLE := Ubiquiti EdgeRouter X-SFP
DEVICE_PACKAGES += kmod-i2c-algo-pca kmod-gpio-pca953x kmod-i2c-gpio-custom
endef
TARGET_DEVICES += ubnt-erx-sfp
define Device/vr500
DTS := VR500
IMAGE_SIZE := 66453504
DEVICE_TITLE := Planex VR500
DEVICE_PACKAGES := kmod-usb3
endef
TARGET_DEVICES += vr500
define Device/w2914nsv2
DTS := W2914NSV2
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := WeVO W2914NS v2
DEVICE_PACKAGES := \
kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += w2914nsv2
define Device/wf-2881
DTS := WF-2881
BLOCKSIZE := 128k
PAGESIZE := 2048
FILESYSTEMS := squashfs
IMAGE_SIZE := 129280k
KERNEL := $(KERNEL_DTB) | pad-offset $$(BLOCKSIZE) 64 | uImage lzma
UBINIZE_OPTS := -E 5
IMAGE/sysupgrade.bin := append-kernel | append-ubi | append-metadata | check-size $$$$(IMAGE_SIZE)
DEVICE_TITLE := NETIS WF-2881
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += wf-2881
define Device/mqmaker_witi-256m
DTS := WITI-256M
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := MQmaker WiTi (256MB RAM)
DEVICE_PACKAGES := \
kmod-ata-core kmod-ata-ahci kmod-mt76x2 kmod-sdhci-mt7620 kmod-usb3 \
kmod-usb-ledtrig-usbport wpad-mini
SUPPORTED_DEVICES += witi
endef
TARGET_DEVICES += mqmaker_witi-256m
define Device/mqmaker_witi-512m
DTS := WITI-512M
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := MQmaker WiTi (512MB RAM)
DEVICE_PACKAGES := \
kmod-ata-core kmod-ata-ahci kmod-mt76x2 kmod-sdhci-mt7620 kmod-usb3 \
kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += mqmaker_witi-512m
define Device/wndr3700v5
DTS := WNDR3700V5
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := Netgear WNDR3700v5
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 wpad-mini
endef
TARGET_DEVICES += wndr3700v5
define Device/youhua_wr1200js
DTS := WR1200JS
IMAGE_SIZE := 16064k
DEVICE_TITLE := YouHua WR1200JS
DEVICE_PACKAGES := \
kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += youhua_wr1200js
define Device/wsr-1166
DTS := WSR-1166
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := Buffalo WSR-1166
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 wpad-mini
endef
TARGET_DEVICES += wsr-1166
define Device/wsr-600
DTS := WSR-600
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := Buffalo WSR-600
DEVICE_PACKAGES := kmod-mt7603 kmod-rt2800-pci wpad-mini
endef
TARGET_DEVICES += wsr-600
define Device/zbt-we1326
DTS := ZBT-WE1326
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := ZBT WE1326
DEVICE_PACKAGES := \
kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-sdhci-mt7620 wpad-mini
endef
TARGET_DEVICES += zbt-we1326
define Device/zbtlink_zbt-we3526
DTS := ZBT-WE3526
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := ZBT WE3526
DEVICE_PACKAGES := \
kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += zbtlink_zbt-we3526
define Device/zbt-wg2626
DTS := ZBT-WG2626
IMAGE_SIZE := $(ralink_default_fw_size_16M)
DEVICE_TITLE := ZBT WG2626
DEVICE_PACKAGES := \
kmod-ata-core kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += zbt-wg2626
define Device/zbt-wg3526-16M
DTS := ZBT-WG3526-16M
IMAGE_SIZE := $(ralink_default_fw_size_16M)
SUPPORTED_DEVICES += zbt-wg3526
DEVICE_TITLE := ZBT WG3526 (16MB flash)
DEVICE_PACKAGES := \
kmod-ata-core kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += zbt-wg3526-16M
define Device/zbt-wg3526-32M
DTS := ZBT-WG3526-32M
IMAGE_SIZE := $(ralink_default_fw_size_32M)
SUPPORTED_DEVICES += ac1200pro
DEVICE_TITLE := ZBT WG3526 (32MB flash)
DEVICE_PACKAGES := \
kmod-ata-core kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
kmod-usb3 kmod-usb-ledtrig-usbport wpad-mini
endef
TARGET_DEVICES += zbt-wg3526-32M
# FIXME: is this still needed?
define Image/Prepare
#define Build/Compile
rm -rf $(KDIR)/relocate
$(CP) ../../generic/image/relocate $(KDIR)
$(MAKE) -C $(KDIR)/relocate KERNEL_ADDR=$(KERNEL_LOADADDR) CROSS_COMPILE=$(TARGET_CROSS)
$(CP) $(KDIR)/relocate/loader.bin $(KDIR)/loader.bin
endef
Reference in a new issue View git blame Copy permalink