KumiSystems/openwrtv3
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity
openwrtv3/target/linux/ipq40xx/image/Makefile
Magnus Frühling 4b280ad91a ipq40xx: add support for ZyXEL WRE6606 
Specifications:
SOC:	Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:	128 MB Nanya NT5CC64M16GP-DI
FLASH:	16 MiB Macronix MX25L12845EMI-12G
ETH:	Qualcomm QCA8072
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT:  WPS, Mode-toggle-switch
LED:	Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS
        (LAN not controllable by software)
        (WLAN each green / red)
SERIAL:	Header next to eth-phy.
        VCC, TX, GND, RX (Square hole is VCC)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet (Correct MAC-address)
 - 2.4 GHz WiFi (Correct MAC-address)
 - 5 GHz WiFi (Correct MAC-address)
 - Factory installation from tftp
 - OpenWRT sysupgrade
 - LEDs
 - WPS Button

Not Working:
 - Mode-toggle-switch

Install via TFTP:

Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command `tftpboot` will pull an initramfs image named
`C0A86302.img` from a tftp server at `192.168.99.08/24`.
After successfull transfer, boot the image with `bootm`.

To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`.

append-cmdline patch taken from chunkeeys work on the NBG6617.

Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
2018-06-18 18:21:20 +02:00

219 lines
6.8 KiB
Makefile
Raw Blame History

include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
define Device/Default
PROFILES := Default
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
KERNEL_PREFIX := $$(IMAGE_PREFIX)
KERNEL_LOADADDR := 0x80208000
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
IMAGE/sysupgrade.bin/squashfs :=
endef
define Device/FitImage
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/FitImageLzma
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/UbiFit
KERNEL_IN_UBI := 1
IMAGES := nand-factory.ubi nand-sysupgrade.bin
IMAGE/nand-factory.ubi := append-ubi
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/DniImage
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
NETGEAR_BOARD_ID :=
NETGEAR_HW_ID :=
IMAGES := factory.img sysupgrade.bin
IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | netgear-dni
IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata
endef
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
define Device/8dev_jalapeno
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_DTS := qcom-ipq4018-jalapeno
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_TITLE := 8devices Jalapeno
endef
TARGET_DEVICES += 8dev_jalapeno
define Device/asus_rt-ac58u
$(call Device/FitImageLzma)
DEVICE_DTS := qcom-ipq4018-rt-ac58u
BLOCKSIZE := 128k
PAGESIZE := 2048
DTB_SIZE := 65536
DEVICE_TITLE := Asus RT-AC58U
IMAGE_SIZE := 20439364
FILESYSTEMS := squashfs
# Someone - in their infinite wisdom - decided to put the firmware
# version in front of the image name \03\00\00\04 => Version 3.0.0.4
# Since u-boot works with strings we either need another fixup step
# to add a version... or we are very careful not to add '\0' into that
# string and call it a day.... Yeah, we do the latter!
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
IMAGES := sysupgrade.bin
DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += asus_rt-ac58u
define Device/avm_fritzbox-4040
$(call Device/FitImageLzma)
DEVICE_DTS := qcom-ipq4018-fritz4040
BOARD_NAME := fritz4040
DEVICE_TITLE := AVM Fritz!Box 4040
IMAGE_SIZE := 29753344
UBOOT_PATH := $$(BIN_DIR)/u-boot-fritz4040/uboot-fritz4040.bin
UBOOT_PARTITION_SIZE := 524288
IMAGES = eva.bin sysupgrade.bin
IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := fritz-tffs fritz-caldata u-boot-fritz4040
endef
TARGET_DEVICES += avm_fritzbox-4040
define Device/compex_wpj428
$(call Device/FitImage)
DEVICE_DTS := qcom-ipq4028-wpj428
DEVICE_DTS_CONFIG := config@4
BLOCKSIZE := 64k
DEVICE_TITLE := Compex WPJ428
IMAGE_SIZE := 31232k
KERNEL_SIZE := 4096k
IMAGES = sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := kmod-gpio-beeper
endef
TARGET_DEVICES += compex_wpj428
define Device/glinet_gl-b1300
$(call Device/FitImage)
DEVICE_TITLE := GL.iNet GL-B1300
BOARD_NAME := gl-b1300
DEVICE_DTS := qcom-ipq4029-gl-b1300
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += glinet_gl-b1300
define Device/meraki_mr33
$(call Device/FitImage)
DEVICE_DTS := qcom-ipq4029-mr33
BLOCKSIZE := 131072
PAGESIZE := 2048
DEVICE_TITLE := Cisco Meraki MR33
IMAGES = sysupgrade.bin
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887
endef
TARGET_DEVICES += meraki_mr33
define Device/netgear_ex61x0v2
$(call Device/DniImage)
KERNEL_SIZE := 3080192
DEVICE_DTS_CONFIG := config@4
NETGEAR_BOARD_ID := EX6150v2series
NETGEAR_HW_ID := 29765285+16+0+128+2x2
endef
define Device/netgear_ex6100v2
$(call Device/netgear_ex61x0v2)
DEVICE_DTS := qcom-ipq4018-ex6100v2
DEVICE_TITLE := Netgear EX6100v2
endef
TARGET_DEVICES += netgear_ex6100v2
define Device/netgear_ex6150v2
$(call Device/netgear_ex61x0v2)
DEVICE_DTS := qcom-ipq4018-ex6150v2
DEVICE_TITLE := Netgear EX6150v2
endef
TARGET_DEVICES += netgear_ex6150v2
define Device/openmesh_a42
$(call Device/FitImageLzma)
DEVICE_DTS := qcom-ipq4018-a42
DEVICE_DTS_CONFIG := config@om.a42
BLOCKSIZE := 64k
DEVICE_TITLE := OpenMesh A42
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15616k
IMAGES = factory.bin sysupgrade.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := uboot-envtools
endef
TARGET_DEVICES += openmesh_a42
define Device/openmesh_a62
$(call Device/FitImageLzma)
DEVICE_DTS := qcom-ipq4019-a62
DEVICE_DTS_CONFIG := config@om.a62
BLOCKSIZE := 64k
DEVICE_TITLE := OpenMesh A62
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15552k
IMAGES = factory.bin sysupgrade.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca9888 uboot-envtools
endef
TARGET_DEVICES += openmesh_a62
define Device/qcom_ap-dk01.1-c1
DEVICE_TITLE := QCA AP-DK01.1-C1
BOARD_NAME := ap-dk01.1-c1
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
KERNEL_INSTALL := 1
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
$(call Device/FitImage)
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += qcom_ap-dk01.1-c1
define Device/qcom_ap-dk04.1-c1
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
KERNEL_INSTALL := 1
KERNEL_SIZE := 4048k
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap-dk04.1-c1
DEVICE_TITLE := QCA AP-DK04.1-C1
endef
TARGET_DEVICES += qcom_ap-dk04.1-c1
define Device/zyxel_wre6606
$(call Device/FitImage)
DEVICE_TITLE := ZyXEL WRE6606
DEVICE_DTS_CONFIG := config@4
DEVICE_DTS := qcom-ipq4018-wre6606
DEVICE_PACKAGES := ipq-wifi-zyxel_wre6606
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += zyxel_wre6606
$(eval $(call BuildImage))
Reference in a new issue View git blame Copy permalink