openwrtv3/target/linux/kirkwood/patches-3.14/150-pogoplug_e02.patch
Luka Perkov 3bb20dedcd kirkwood: add Pogoplug E02 kernel support for 3.14
This also fixes a typo in the UBIFS_OPTS

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>

SVN-Revision: 40827
2014-05-23 08:16:56 +00:00

127 lines
2.5 KiB
Diff

--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -112,6 +112,7 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-
kirkwood-nsa310a.dtb \
kirkwood-openblocks_a6.dtb \
kirkwood-openblocks_a7.dtb \
+ kirkwood-pogo_e02.dtb \
kirkwood-sheevaplug.dtb \
kirkwood-sheevaplug-esata.dtb \
kirkwood-topkick.dtb \
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
@@ -0,0 +1,114 @@
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "Cloud Engines Pogoplug E02";
+ compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ };
+
+ ocp@f1000000 {
+ pinctrl: pinctrl@10000 {
+ pmx_usb_power_enable: pmx-usb-power-enable {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+ pmx_led_green: pmx-led_green {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+ pmx_led_orange: pmx-led_orange {
+ marvell,pins = "mpp49";
+ marvell,function = "gpio";
+ };
+ };
+ serial@12000 {
+ status = "ok";
+ };
+ };
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
+ &pmx_led_green >;
+ pinctrl-names = "default";
+
+ health {
+ label = "status:green:health";
+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+ fault {
+ label = "status:orange:fault";
+ gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+ };
+ };
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_usb_power_enable>;
+ pinctrl-names = "default";
+
+ usb_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&nand {
+ chip-delay = <40>;
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "uImage";
+ reg = <0x0100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "pogoplug";
+ reg = <0x0500000 0x2000000>;
+ };
+
+ partition@2500000 {
+ label = "root";
+ reg = <0x02500000 0x5b00000>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+&eth0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <&ethphy0>;
+ };
+};