c4c72a9a42
This fixes the LED configuration for the D-Link DIR-869 A1. In order to
support the device I probed around using an initramfs image for the
UniFi AC. Pulling GPIO 15 to low enabled the LEDs while high disabled them.
GPIO 16 set to low meant that the color was white while pulling it to high
made the color change to orange. The past code was written based upon these
findings.
However, running a flashed image I now discovered that GPIO 15 controls the
orange LEDs while GPIO 16 controls the white ones and that both are active
when low. This means that the GPIOs were inverted and one active_low was set
wrong which this patch fixes.
Behavior of the LED front after this patch is applied:
cat /sys/devices/platform/leds-gpio/leds/d-link:white:status/brightness
0 -> white LEDs are OFF
255 -> white LEDs are ON
cat /sys/devices/platform/leds-gpio/leds/d-link🍊status/brightness
0 -> orange LEDs are OFF
255 -> orange LEDs are ON
If the brightness of both is set to 255 the LED front will be white.
If the brightness of both is set to 0 the LED front will be off.
Signed-off-by: Florian Beier <beier.florian@gmail.com>
175 lines
4.3 KiB
C
175 lines
4.3 KiB
C
/*
|
|
* D-Link DIR-869 A1 support
|
|
*
|
|
* Copyright (C) 2015-2016 P. Wassi <p.wassi at gmx.at>
|
|
* Copyright (C) 2016 Matthias Schiffer <mschiffer@universe-factory.net>
|
|
*
|
|
* Derived from: mach-ubnt-unifiac.c
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License version 2 as published
|
|
* by the Free Software Foundation.
|
|
*/
|
|
|
|
|
|
#include <linux/gpio.h>
|
|
#include <linux/init.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/ath9k_platform.h>
|
|
|
|
#include <asm/mach-ath79/ath79.h>
|
|
#include <asm/mach-ath79/irq.h>
|
|
#include <asm/mach-ath79/ar71xx_regs.h>
|
|
|
|
#include <linux/platform_data/phy-at803x.h>
|
|
#include <linux/ar8216_platform.h>
|
|
|
|
#include "common.h"
|
|
#include "dev-ap9x-pci.h"
|
|
#include "dev-eth.h"
|
|
#include "dev-gpio-buttons.h"
|
|
#include "dev-leds-gpio.h"
|
|
#include "dev-m25p80.h"
|
|
#include "dev-wmac.h"
|
|
#include "machtypes.h"
|
|
#include "nvram.h"
|
|
|
|
|
|
#define DIR869A1_GPIO_BTN_RESET 1
|
|
#define DIR869A1_GPIO_BTN_WPS 2
|
|
#define DIR869A1_GPIO_SWITCH_MODE 8
|
|
|
|
#define DIR869A1_GPIO_ENABLE_SWITCH 11
|
|
|
|
#define DIR869A1_GPIO_LED_ORANGE 15
|
|
#define DIR869A1_GPIO_LED_WHITE 16
|
|
|
|
#define DIR869A1_KEYS_POLL_INTERVAL 20 /* msecs */
|
|
#define DIR869A1_KEYS_DEBOUNCE_INTERVAL (3 * DIR869A1_KEYS_POLL_INTERVAL)
|
|
|
|
|
|
#define DIR869A1_DEVDATA_ADDR 0x1f050000
|
|
#define DIR869A1_DEVDATA_SIZE 0x10000
|
|
|
|
#define DIR869A1_EEPROM_ADDR 0x1fff0000
|
|
#define DIR869A1_WMAC_CALDATA_OFFSET 0x1000
|
|
#define DIR869A1_PCI_CALDATA_OFFSET 0x5000
|
|
|
|
|
|
static struct gpio_led dir869a1_leds_gpio[] __initdata = {
|
|
{
|
|
.name = "d-link:white:status",
|
|
.gpio = DIR869A1_GPIO_LED_WHITE,
|
|
.active_low = 1,
|
|
},
|
|
{
|
|
.name = "d-link:orange:status",
|
|
.gpio = DIR869A1_GPIO_LED_ORANGE,
|
|
.active_low = 1,
|
|
},
|
|
};
|
|
|
|
static struct gpio_keys_button dir869a1_gpio_keys[] __initdata = {
|
|
{
|
|
.desc = "reset",
|
|
.type = EV_KEY,
|
|
.code = KEY_RESTART,
|
|
.debounce_interval = DIR869A1_KEYS_DEBOUNCE_INTERVAL,
|
|
.gpio = DIR869A1_GPIO_BTN_RESET,
|
|
.active_low = 1,
|
|
},
|
|
{
|
|
.desc = "wps",
|
|
.type = EV_KEY,
|
|
.code = KEY_WPS_BUTTON,
|
|
.debounce_interval = DIR869A1_KEYS_DEBOUNCE_INTERVAL,
|
|
.gpio = DIR869A1_GPIO_BTN_WPS,
|
|
.active_low = 1,
|
|
},
|
|
{
|
|
.desc = "mode",
|
|
.type = EV_SW,
|
|
.code = BTN_0,
|
|
.debounce_interval = DIR869A1_KEYS_DEBOUNCE_INTERVAL,
|
|
.gpio = DIR869A1_GPIO_SWITCH_MODE,
|
|
.active_low = 0,
|
|
},
|
|
};
|
|
|
|
|
|
static struct ar8327_pad_cfg dir869a1_ar8327_pad0_cfg = {
|
|
.mode = AR8327_PAD_MAC_SGMII,
|
|
.sgmii_delay_en = true,
|
|
};
|
|
|
|
static struct ar8327_platform_data dir869a1_ar8327_data = {
|
|
.pad0_cfg = &dir869a1_ar8327_pad0_cfg,
|
|
.port0_cfg = {
|
|
.force_link = 1,
|
|
.speed = AR8327_PORT_SPEED_1000,
|
|
.duplex = 1,
|
|
.txpause = 1,
|
|
.rxpause = 1,
|
|
},
|
|
};
|
|
|
|
|
|
static struct mdio_board_info dir869a1_mdio0_info[] = {
|
|
{
|
|
.bus_id = "ag71xx-mdio.0",
|
|
.phy_addr = 0,
|
|
.platform_data = &dir869a1_ar8327_data,
|
|
},
|
|
};
|
|
|
|
|
|
static void dir869a1_get_mac(const char *name, char *mac)
|
|
{
|
|
u8 *nvram = (u8 *) KSEG1ADDR(DIR869A1_DEVDATA_ADDR);
|
|
int err;
|
|
|
|
err = ath79_nvram_parse_mac_addr(nvram, DIR869A1_DEVDATA_SIZE,
|
|
name, mac);
|
|
if (err)
|
|
pr_err("no MAC address found for %s\n", name);
|
|
}
|
|
|
|
static void __init dir869a1_setup(void)
|
|
{
|
|
u8 *eeprom = (u8 *) KSEG1ADDR(DIR869A1_EEPROM_ADDR);
|
|
u8 wlan24mac[ETH_ALEN] = {}, wlan5mac[ETH_ALEN] = {};
|
|
|
|
ath79_register_m25p80(NULL);
|
|
|
|
gpio_request_one(DIR869A1_GPIO_ENABLE_SWITCH,
|
|
GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
|
|
"Switch power");
|
|
|
|
dir869a1_get_mac("lanmac=", ath79_eth0_data.mac_addr);
|
|
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
|
|
ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
|
|
ath79_eth0_data.phy_mask = BIT(0);
|
|
|
|
mdiobus_register_board_info(dir869a1_mdio0_info,
|
|
ARRAY_SIZE(dir869a1_mdio0_info));
|
|
|
|
ath79_register_mdio(0, 0);
|
|
ath79_register_eth(0);
|
|
|
|
dir869a1_get_mac("wlan24mac=", wlan24mac);
|
|
ath79_register_wmac(eeprom + DIR869A1_WMAC_CALDATA_OFFSET, wlan24mac);
|
|
|
|
dir869a1_get_mac("wlan5mac=", wlan5mac);
|
|
ap91_pci_init(eeprom + DIR869A1_PCI_CALDATA_OFFSET, wlan5mac);
|
|
|
|
ath79_register_leds_gpio(-1, ARRAY_SIZE(dir869a1_leds_gpio),
|
|
dir869a1_leds_gpio);
|
|
|
|
ath79_register_gpio_keys_polled(-1, DIR869A1_KEYS_POLL_INTERVAL,
|
|
ARRAY_SIZE(dir869a1_gpio_keys),
|
|
dir869a1_gpio_keys);
|
|
}
|
|
|
|
MIPS_MACHINE(ATH79_MACH_DIR_869_A1, "DIR-869-A1", "D-Link DIR-869 rev. A1",
|
|
dir869a1_setup);
|