23f9b2d9a9
This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor 5 GHz AC access point with an integrated 120° 16 dBi antenna. The device was previously known as LiteBeam AP ac but was later rebranded. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Ports: 1 GbE port (PoE in) WLAN: 5 GHz QCA899X (PCI) The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). It is very similar to the NanoStation loco AC, except for the 2.4 GHz management radio (missing here). Installation procedure is the same as the NanoStation [loco] AC: 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
256 lines
6.3 KiB
Bash
Executable file
256 lines
6.3 KiB
Bash
Executable file
#!/bin/sh
|
|
|
|
. /lib/functions/system.sh
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/k2t.sh
|
|
|
|
ath79_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
avm,fritz300e|\
|
|
ocedo,koala|\
|
|
ocedo,raccoon|\
|
|
pcs,cap324|\
|
|
pisen,wmm003n|\
|
|
tplink,re450-v2|\
|
|
tplink,tl-mr10u|\
|
|
tplink,tl-mr3020-v1|\
|
|
tplink,tl-mr3040-v2|\
|
|
tplink,tl-wa901nd-v2|\
|
|
tplink,tl-wr703n|\
|
|
ubnt,bullet-m|\
|
|
ubnt,lap-120|\
|
|
ubnt,nanostation-ac-loco|\
|
|
ubnt,rocket-m|\
|
|
ubnt,unifiac-lite|\
|
|
ubnt,unifiac-mesh|\
|
|
ubnt,unifi|\
|
|
wd,mynet-wifi-rangeextender)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
avm,fritz4020)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
|
|
;;
|
|
buffalo,bhr-4grv|\
|
|
buffalo,wzr-hp-g450h)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan"
|
|
;;
|
|
buffalo,bhr-4grv2)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "6@eth0"
|
|
;;
|
|
buffalo,wzr-hp-ag300h)
|
|
ucidef_set_interface_wan "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
buffalo,wzr-hp-g302h-a1a0)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:lan:1" "3:lan:4" "4:lan:3" "5:lan:2" "2:wan"
|
|
;;
|
|
dlink,dir-825-b1)
|
|
ucidef_set_interface_wan "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "5@eth0"
|
|
;;
|
|
elecom,wrc-300ghbk2-i)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan:4" "3:lan:3" "4:lan:2" "5:lan:1" "1:wan"
|
|
;;
|
|
embeddedwireless,dorin)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:wan" "2:lan:3" "3:lan:2"
|
|
;;
|
|
etactica,eg200)
|
|
ucidef_set_interface_lan "eth0" "dhcp"
|
|
;;
|
|
glinet,ar150|\
|
|
glinet,ar300m)
|
|
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
|
;;
|
|
iodata,etg3-r|\
|
|
iodata,wn-ac1167dgr|\
|
|
iodata,wn-ac1600dgr2|\
|
|
pcs,cr5000)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
|
|
;;
|
|
netgear,wndr3700|\
|
|
netgear,wndr3700v2|\
|
|
netgear,wndr3800)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5u@eth0"
|
|
ucidef_add_switch_attr "switch0" "blinkrate" 2
|
|
ucidef_add_switch_port_attr "switch0" 1 led 6
|
|
ucidef_add_switch_port_attr "switch0" 2 led 9
|
|
ucidef_add_switch_port_attr "switch0" 5 led 2
|
|
;;
|
|
netgear,wnr612-v2|\
|
|
on,n150r)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan" "2:lan" "3:lan:3" "4:lan:4"
|
|
;;
|
|
pcs,cr3000)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
|
|
ucidef_set_interface_wan "eth0"
|
|
;;
|
|
phicomm,k2t)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "3:lan:1" "5:lan:2" "4:wan"
|
|
;;
|
|
tplink,archer-c7-v1|\
|
|
tplink,archer-c7-v2|\
|
|
tplink,tl-wdr4900-v2)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6@eth0" "1:wan"
|
|
;;
|
|
buffalo,whr-g301n|\
|
|
tplink,tl-mr3220-v1|\
|
|
tplink,tl-mr3420-v1|\
|
|
tplink,tl-wr841-v7)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
tplink,tl-wdr3600|\
|
|
tplink,tl-wdr4300)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan:1" "3:lan:2" "4:lan:3" "5:lan:4" "1:wan"
|
|
;;
|
|
tplink,tl-wr1043nd-v1)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
|
|
;;
|
|
tplink,tl-wr1043nd-v2|\
|
|
tplink,tl-wr1043nd-v3)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" "6@eth0"
|
|
;;
|
|
tplink,tl-wr1043nd-v4)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
|
|
;;
|
|
tplink,tl-wr2543-v1)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
|
|
;;
|
|
tplink,tl-wr740n-v1|\
|
|
tplink,tl-wr740n-v3|\
|
|
tplink,tl-wr741-v1|\
|
|
tplink,tl-wr743nd-v1|\
|
|
tplink,tl-wr841-v5|\
|
|
tplink,tl-wr941-v4)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
|
|
;;
|
|
tplink,tl-wr740nd-v4|\
|
|
tplink,tl-wr741nd-v4|\
|
|
tplink,tl-wr841-v9|\
|
|
tplink,tl-wr841-v11)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
tplink,tl-wr842n-v2)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"
|
|
;;
|
|
tplink,tl-wr941-v2)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
|
|
;;
|
|
ubnt,routerstation)
|
|
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
|
;;
|
|
ubnt,routerstation-pro)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
ubnt,nanostation-ac|\
|
|
ubnt,unifiac-mesh-pro|\
|
|
ubnt,unifiac-pro)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan" "3:wan"
|
|
;;
|
|
*)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
ath79_setup_macs()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
avm,fritz300e)
|
|
lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
|
|
;;
|
|
avm,fritz4020)
|
|
lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
|
|
wan_mac=$(fritz_tffs -n macb -i $(find_mtd_part "tffs (1)"))
|
|
;;
|
|
dlink,dir-825-b1)
|
|
lan_mac=$(mtd_get_mac_text "caldata" 65440)
|
|
wan_mac=$(mtd_get_mac_text "caldata" 65460)
|
|
;;
|
|
elecom,wrc-300ghbk2-i)
|
|
wan_mac=$(macaddr_add "$(mtd_get_mac_binary ART 4098)" -2)
|
|
;;
|
|
iodata,etg3-r)
|
|
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
|
wan_mac=$(macaddr_add "$lan_mac" -1)
|
|
;;
|
|
iodata,wn-ac1167dgr|\
|
|
iodata,wn-ac1600dgr2)
|
|
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
|
|
;;
|
|
netgear,wndr3700|\
|
|
netgear,wndr3700v2|\
|
|
netgear,wndr3800)
|
|
lan_mac=$(macaddr_setbit_la "$(mtd_get_mac_binary art 0)")
|
|
;;
|
|
phicomm,k2t)
|
|
lan_mac=$(k2t_get_mac "lan_mac")
|
|
wan_mac=$(k2t_get_mac "wan_mac")
|
|
;;
|
|
tplink,tl-wr1043nd-v4)
|
|
base_mac=$(mtd_get_mac_binary product-info 8)
|
|
wan_mac=$(macaddr_add "$base_mac" 1)
|
|
;;
|
|
tplink,tl-wr941-v2)
|
|
base_mac=$(mtd_get_mac_binary u-boot 130048)
|
|
wan_mac=$(macaddr_add "$base_mac" 1)
|
|
;;
|
|
ubnt,routerstation|\
|
|
ubnt,routerstation-pro)
|
|
wan_mac=$(fconfig -s -r -d $(find_mtd_part "RedBoot config") -n ar7100_esa)
|
|
lan_mac=$(macaddr_add "$wan_mac" 1)
|
|
;;
|
|
wd,mynet-wifi-rangeextender)
|
|
lan_mac=$(nvram get et0macaddr)
|
|
;;
|
|
esac
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
ath79_setup_interfaces $board
|
|
ath79_setup_macs $board
|
|
board_config_flush
|
|
|
|
exit 0
|