8f4dfadd5a
Use diag.sh version used for other targets supporting different leds for the different boot states. The existing led sequences should be the same as before. Signed-off-by: Mathias Kresin <dev@kresin.me>
148 lines
2.4 KiB
Text
148 lines
2.4 KiB
Text
/dts-v1/;
|
|
|
|
#include "rt2880.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "dlink,dap-1522-a1", "ralink,rt2880-soc";
|
|
model = "D-Link DAP-1522 A1";
|
|
|
|
aliases {
|
|
led-boot = &led_status;
|
|
led-failsafe = &led_status;
|
|
led-running = &led_status;
|
|
led-upgrade = &led_status;
|
|
};
|
|
|
|
cfi@bc400000 {
|
|
compatible = "cfi-flash";
|
|
reg = <0xbc400000 0x800000>;
|
|
bank-width = <2>;
|
|
device-width = <2>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "uboot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@30000 {
|
|
label = "factory";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "firmware";
|
|
reg = <0x40000 0x3a0000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
rtl8366s {
|
|
compatible = "realtek,rtl8366s";
|
|
gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>;
|
|
gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <100>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio2 16 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
|
|
ap {
|
|
label = "ap";
|
|
gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
|
|
bridge {
|
|
label = "bridge";
|
|
gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_1>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wps {
|
|
label = "dap-1522-a1:blue:wps";
|
|
gpios = <&gpio2 17 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
ap {
|
|
label = "dap-1522-a1:blue:ap";
|
|
gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
sta {
|
|
label = "dap-1522-a1:red:sta";
|
|
gpios = <&gpio2 19 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_status: status {
|
|
label = "dap-1522-a1:blue:status";
|
|
gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&pinctrl {
|
|
state_default: pinctrl0 {
|
|
gpio {
|
|
ralink,group = "i2c", "uartlite", "pci";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
status = "okay";
|
|
mtd-mac-address = <&factory 0x2004>;
|
|
|
|
port@0 {
|
|
mediatek,fixed-link = <1000 1 1 1>;
|
|
};
|
|
|
|
mdio-bus {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
phy-mode = "mii";
|
|
reg = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
ralink,mtd-eeprom = <&factory 0x2000>;
|
|
};
|