openwrtv3/target/linux/lantiq/dts/VR200v.dts
Mathias Kresin 18c64f41c7 treewide: fix button keys codes used in dts
Use keycodes that matches the intended use case based on the label.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:34:23 +01:00

277 lines
5.1 KiB
Text

/dts-v1/;
#include "vr9.dtsi"
#include <dt-bindings/input/input.h>
/ {
model = "VR200v - TP-LINK Archer VR200v";
chosen {
bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
};
aliases {
led-boot = &power;
led-failsafe = &power;
led-dsl = &dsl;
led-internet = &internet;
led-usb = &usb;
led-usb2 = &usb;
};
memory@0 {
reg = <0x0 0x7f00000>;
};
fpi@10000000 {
gpio: pinmux@E100B10 {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
mdio {
lantiq,groups = "mdio";
lantiq,function = "mdio";
};
gphy-leds {
lantiq,groups = "gphy0 led1", "gphy1 led1";
lantiq,function = "gphy";
lantiq,pull = <2>;
lantiq,open-drain = <0>;
lantiq,output = <1>;
};
phy-rst {
lantiq,pins = "io42";
lantiq,pull = <0>;
lantiq,open-drain = <0>;
lantiq,output = <1>;
};
pcie-rst {
lantiq,pins = "io38";
lantiq,pull = <0>;
lantiq,output = <1>;
};
};
pins_spi_default: pins_spi_default {
spi_in {
lantiq,groups = "spi_di";
lantiq,function = "spi";
};
spi_out {
lantiq,groups = "spi_do", "spi_clk",
"spi_cs4";
lantiq,function = "spi";
lantiq,output = <1>;
};
};
};
ifxhcd@E101000 {
status = "okay";
gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
lantiq,portmask = <0x3>;
};
ifxhcd@E106000 {
status = "okay";
gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
};
};
gphy-xrx200 {
compatible = "lantiq,phy-xrx200";
firmware = "lantiq/vr9_phy11g_a2x.bin";
phys = [ 00 01 ];
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
reset {
label = "reset";
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wifi {
label = "wifi";
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_RFKILL>;
linux,input-type = <EV_SW>;
};
wps {
label = "wps";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
dect_paging {
label = "dect_paging";
gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
linux,code = <KEY_PHONE>;
};
};
gpio-leds {
compatible = "gpio-leds";
power: power {
label = "vr200v:blue:power";
gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
dsl: dsl {
label = "vr200v:blue:dsl";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
};
internet: internet {
label = "vr200v:blue:internet";
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
};
usb: usb {
label = "vr200v:blue:usb";
gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
};
eth {
label = "vr200v:blue:lan";
gpios = <&gpio 40 GPIO_ACTIVE_LOW>;
};
wlan {
label = "vr200v:blue:wlan";
gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
};
wlan5g {
label = "vr200v:blue:wlan5g";
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
};
phone {
label = "vr200v:blue:phone";
gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
};
};
};
&spi {
pinctrl-names = "default";
pinctrl-0 = <&pins_spi_default>;
status = "ok";
m25p80@4 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <4 0>;
spi-max-frequency = <33250000>;
m25p,fast-read;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
reg = <0x0 0x20000>;
label = "u-boot";
read-only;
};
partition@20000 {
reg = <0x20000 0xf90000>;
label = "firmware";
};
partition@fb0000 {
reg = <0xfb0000 0x10000>;
label = "radioDECT";
read-only;
};
partition@fc0000 {
reg = <0xfc0000 0x10000>;
label = "config";
read-only;
};
romfile: partition@fd0000 {
reg = <0xfd0000 0x10000>;
label = "romfile";
read-only;
};
partition@fe0000 {
reg = <0xfe0000 0x10000>;
label = "rom";
read-only;
};
partition@ff0000 {
reg = <0xff0000 0x10000>;
label = "radio";
read-only;
};
};
};
};
&eth0 {
lan: interface@0 {
compatible = "lantiq,xrx200-pdi";
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
mtd-mac-address = <&romfile 0xf100>;
lantiq,switch;
ethernet@0 {
compatible = "lantiq,xrx200-pdi-port";
reg = <0>;
phy-mode = "rgmii";
phy-handle = <&phy0>;
// gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
};
ethernet@5 {
compatible = "lantiq,xrx200-pdi-port";
reg = <5>;
phy-mode = "rgmii";
phy-handle = <&phy5>;
};
ethernet@2 {
compatible = "lantiq,xrx200-pdi-port";
reg = <2>;
phy-mode = "gmii";
phy-handle = <&phy11>;
};
ethernet@3 {
compatible = "lantiq,xrx200-pdi-port";
reg = <4>;
phy-mode = "gmii";
phy-handle = <&phy13>;
};
};
mdio@0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "lantiq,xrx200-mdio";
phy0: ethernet-phy@0 {
reg = <0x0>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
phy5: ethernet-phy@5 {
reg = <0x5>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
phy11: ethernet-phy@11 {
reg = <0x11>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
phy13: ethernet-phy@13 {
reg = <0x13>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
};
};