openwrtv3/target/linux/ramips/dts/GL-MT300N-V2.dts
Mathias Kresin 95fe3c51e5 ramips: fix polarity in gpio-export node
If we need to set the initial output value to GPIOF_OUT_INIT_HIGH (1) to
enable something, the pin is ACTIVE_HIGH. The same applies to
GPIOF_OUT_INIT_LOW (0) and ACTIVE_LOW.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-18 09:32:27 +01:00

133 lines
2 KiB
Text

/dts-v1/;
#include "mt7628an.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/{
compatible = "glinet,gl-mt300n-v2", "ralink,mt7620an-soc";
model = "GL-MT300N-V2";
chosen {
bootargs = "console=ttyS0,115200";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x8000000>;
};
gpio-leds {
compatible = "gpio-leds";
wan {
label = "gl-mt300n-v2:blue:wan";
gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
};
wlan {
label = "gl-mt300n-v2:red:wlan";
gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
};
};
gpio-keys {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <20>;
reset {
label = "reset";
gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
BTN_0 {
label = "BTN_0";
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
};
BTN_1 {
label = "BTN_1";
gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
linux,code = <BTN_1>;
};
};
gpio_export {
compatible = "gpio-export";
#size-cells = <0>;
usb {
gpio-export,name = "usb";
gpio-export,output = <1>;
gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
};
};
};
&pinctrl {
state_default: pinctrl0 {
gpio {
ralink,group = "wdt", "gpio", "wled_an", "p0led_an", "i2s";
ralink,function = "gpio";
};
};
};
&ethernet {
mtd-mac-address = <&factory 0x4>;
};
&wmac {
status = "okay";
ralink,mtd-eeprom = <&factory 0x0>;
};
&spi0 {
status = "okay";
m25p80@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <10000000>;
m25p,chunked-io = <32>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "u-boot-env";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
label = "firmware";
reg = <0x50000 0xfb0000>;
};
};
};
&ehci {
status = "okay";
};
&ohci {
status = "okay";
};