04d3308b62
This patch adds support for GL.iNet GL-B1300 Specification: - SOC: IPQ4028 / QCA Dakota - RAM: 256 MiB - FLASH: 32 MiB - ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN) - USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) - WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2 - WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2 - INPUT: one reset and one WPS button - LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved - UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1 Installation: Method 1: - use serial port to stop uboot - uboot command: run lf Method 2: - push down reset button and power on - wait until three leds constantly on then release - upgrade by uboot web at http://192.168.1.1 Note: - the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method. - the sysupgrade image can be automatically downloaded if tftp server at 192.168.1.2 have that file. - the wifi led will be flashing when writing image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
63 lines
1.6 KiB
Bash
Executable file
63 lines
1.6 KiB
Bash
Executable file
#!/bin/sh
|
|
#
|
|
# Copyright (c) 2015 The Linux Foundation. All rights reserved.
|
|
# Copyright (c) 2011-2015 OpenWrt.org
|
|
#
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
board_config_update
|
|
|
|
board=$(board_name)
|
|
|
|
case "$board" in
|
|
avm,fritzbox-4040)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
|
|
;;
|
|
linksys,ea8500)
|
|
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
|
|
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
|
|
ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
|
|
;;
|
|
netgear,d7800 |\
|
|
netgear,r7500 |\
|
|
netgear,r7500v2 |\
|
|
netgear,r7800 |\
|
|
qcom,ipq8064-ap148 |\
|
|
tplink,vr2600v)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
|
|
;;
|
|
glinet,gl-b1300 |\
|
|
openmesh,a42)
|
|
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
|
;;
|
|
qcom,ipq8064-db149)
|
|
ucidef_set_interface_lan "eth1 eth2 eth3"
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "6u@eth1" "5:wan" "0u@eth0"
|
|
;;
|
|
tplink,c2600)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "6@eth1" "5:wan" "0@eth0"
|
|
;;
|
|
zyxel,nbg6817)
|
|
hw_mac_addr=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
|
|
ucidef_set_interface_macaddr "lan" "$(macaddr_add $hw_mac_addr 2)"
|
|
ucidef_set_interface_macaddr "wan" "$(macaddr_add $hw_mac_addr 3)"
|
|
;;
|
|
*)
|
|
echo "Unsupported hardware. Network interfaces not intialized"
|
|
;;
|
|
esac
|
|
|
|
board_config_flush
|
|
|
|
exit 0
|