hostapd supports "Dynamic Authorization Extensions", making it possible
to forcibly disconnect a user by sending it a RADIUS "Disconnect-Request"
packet.
I've added three new variables to enable setting of the
"radius_das_client" and "radius_das_port" variables in the hostapd
configuration, which enable these extensions.
* dae_client - IP of the client that can send disconnect requests
* dae_secret - shared secret for DAE packets
These are combined into the "radius_das_client" option in hostapd.conf
To enable the server, both dae_client and dae_secret must be set.
* dae_port - optional, default value is 3799 as specified in RFC 5176
Signed-off-by: Martijn van de Streek <martijn@vandestreek.net>
SVN-Revision: 37734
WEP in WDS is currently broken in hostapd. Add a patch
to fix the issue.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
SVN-Revision: 37733
Use the "start_disabled" option in hostapd that was added
in the earlier patch.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
SVN-Revision: 37732
Add a patch for hostapd that introduces a config option
"start_disabled" which can be used to bring up an AP
interface with beaconing disabled. This is useful in
a Repeater-AP setup where the Repeater AP has to start
beaconing only after the WDS link has been established.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
SVN-Revision: 37730
*) can not connect to switch chip
*) only one usb port is working
*) wifi is not working
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37712
The BCM4331 supports a PCIe max request size of 512 bytes and uses
that, but the PCIe controller in the BCM4706 just supports 128 Bytes
and that causes a DMA error for packages bigger than 126 bytes. This
fixes the problem by setting the BCM4331 also to 128 Bytes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37709
Parallel flash access on RT3662/RT3883 based devices
is broken without that. It was fixed already some time
ago, but that change seems lost somewhere.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37708
The current dependency prevents building of the
rt2800{pci,usb} drivers for RT3883. Change the
dependency to fix this.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37699
This patch fixes the code of the buttons for TP-Link WA901ND.
Signed-off-by: Rocco Folino <lordzen@autistici.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37696
Job control is turned off because it cannot obtain controlling terminal on
/dev/console, so it is impossible to do any job control operation behind
real x86 device (keyboard+monitor or virtualized).
This patch switches /dev/console to tty devices for ash on x86 generic target.
Signed-off-by: Jiri Slachta <slachta@cesnet.cz>
SVN-Revision: 37693
When CONFIG_LLC gets build as a module, also p8022.ko and psnap.ko are
getting build as a module. kmod-appletalk depends on llc.ko and
psnap.ko, but at least psnap.ko,was not packed. On most systems
CONFIG_LLC will be build into the kernel so this problem does not show
up.
This fixes the missing dependency of kmod-appletalk on psnap.ko
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37673
CONFIG_FW_LOADER=y is set in the generic config and our packages in
packages/kernel/linux are depending on it to be compiled into the
kernel.
This fixes some dependency problem where kmod-r8169 misses
firmware_class.ko.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37672
