hand over parameters to user-script e.g. $1=deconfig
Signed-off-by: Leon George <leon@georgemail.de>
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 45626
The WAN port should at least respond to IGMP and MLD queries as
otherwise a snooping bridge/switch might drop traffic.
RFC4890 recommends to leave IGMP and MLD unfiltered as they are always
link-scoped anyways.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 45613
OpenVPN assumes that its control channel messages are sent and received
unfragmented, this assumption is broken when CBC record splitting is
enabled in mbedTLS.
The record splitting is intended as countermeasure against BEAST attacks
which do not apply to OpenVPN, therefore we simply disable it until
upstream OpenVPN gains the ability to process fragmented control
messages.
Disabling the splitting also works around a (not remotely triggerable)
segmentation fault in mbedTLS.
References:
* https://dev.openwrt.org/ticket/19101
* https://community.openvpn.net/openvpn/ticket/524
* https://github.com/ARMmbed/mbedtls/pull/185
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45602
The most significant change from the previous version is the trimming of
the 300-ip_tiny.patch to lib/utils.c where a section previously patched
had vanished. That section of the patch was removed.
Built and lightly tested on ar71xx against uClibc and musl.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 45512
Hostapd's control file location was changed in 2013, and that has apparently
broken the wps button hotplug script in cases where there are multiple radios
and wps is possibly configured also for the second radio. The current wps
button hotplug script always handles only the first radio.
https://dev.openwrt.org/browser/trunk/package/network/services/hostapd/files/wps-hotplug.sh
The reason is that the button hotplug script seeks directories like
/var/run/hostapd*, as the hostapd-phy0.conf files were earlier in
per-interface subdirectories.
Currently the *.conf files are directly in /var/run and the control sockets
are in /var/run/hostapd, but there is no subdirectory for each radio.
root@OpenWrt:/# ls /var/run/hostapd*
/var/run/hostapd-phy0.conf /var/run/hostapd-phy1.conf
/var/run/hostapd:
wlan0 wlan1
The hotplug script was attempted to be fixed after the hostapd change by
r38986 in Dec2013, but that change only unbroke the script for the first
radio, but left it broken for multiple radios.
https://dev.openwrt.org/changeset/38986/
The script fails to find subdirectories with [ -d "$dir" ], and passes just
the only found directory /var/run/hostapd, leading into activating only the
first radio, as hostapd_cli defaults to first socket found inthe passed
directory:
root@OpenWrt:/# hostapd_cli -?
...
usage: hostapd_cli [-p<path>] [-i<ifname>] [-hvB] [-a<path>] \
[-G<ping interval>] [command..]
...
-p<path> path to find control sockets (default: /var/run/hostapd)
...
-i<ifname> Interface to listen on (default: first interface found in the
socket path)
Below is a run with the default script and with my proposed solution.
Default script (with logging added):
==================================
root@OpenWrt:/# cat /etc/rc.button/wps
#!/bin/sh
if [ "$ACTION" = "pressed" -a "$BUTTON" = "wps" ]; then
for dir in /var/run/hostapd*; do
[ -d "$dir" ] || continue
logger "WPS activated for: $dir"
hostapd_cli -p "$dir" wps_pbc
done
fi
>>>> WPS BUTTON PRESSED <<<<<
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan0 wps_get_status
PBC Status: Active
Last WPS result: None
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan1 wps_get_status
PBC Status: Timed-out
Last WPS result: None
root@OpenWrt:/# logread | grep WPS
Tue Apr 14 18:38:50 2015 user.notice root: WPS activated for: /var/run/hostapd
wlan0 got WPS activated, while wlan1 remained inactive.
I have modified the script to search for sockets instead of directories and
to use the "-i" option with hostapd_cli, and now the script properly
activates wps for both radios. As "-i" needs the interface name instead of
the full path, the script first changes dir to /var/run/hostapd to get simply
the interface names.
Modified script (with logging):
===============================
root@OpenWrt:/# cat /etc/rc.button/wps
#!/bin/sh
if [ "$ACTION" = "pressed" -a "$BUTTON" = "wps" ]; then
cd /var/run/hostapd
for dir in *; do
[ -S "$socket" ] || continue
logger "WPS activated for: $socket"
hostapd_cli -i "$socket" wps_pbc
done
fi
>>>> WPS BUTTON PRESSED <<<<<
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan0 wps_get_status
PBC Status: Active
Last WPS result: None
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan1 wps_get_status
PBC Status: Active
Last WPS result: None
root@OpenWrt:/# logread | grep WPS
Tue Apr 14 18:53:06 2015 user.notice root: WPS activated for: wlan0
Tue Apr 14 18:53:06 2015 user.notice root: WPS activated for: wlan1
Both radios got their WPS activated properly.
I am not sure if my solution is optimal, but it seems to work. WPS button is
maybe not that often used functionality, but it might be fixed in any case.
Routers with multiple radios are common now, so the bug is maybe more
prominent than earlier.
The modified script has been in a slightly different format in my community
build since r42420 in September 2014.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45492
Two errors "netifd: radio0: sh: bad number" have recently surfaced in system
log in trunk when wifi interfaces come up. I tracked the errors to checking
numerical values of some config options without ensuring that the option has
any value.
The errors I see have apparently been introduced by r45051 (ieee80211r in
hostapd) and r45326 (start_disabled in mac80211). My patches fix two
instances of "bad number", but there may be a third one, as the original
report in bug 19345 pre-dates r45326 and already has two "bad number" errors
for radio0.
https://dev.openwrt.org/ticket/19345
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45380
r45270 removed ieee80211n=%d from the format string but didn't remove
the parameter itself. Though this probably doesn't cause any harm, it's
quite confusing and unneeded.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45351
it causes problems with newer iptables when ipv6 is disabled as iptc uncoditionally links ip6tc
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 45350
This patch adds the wpan-tools (iwpan) utility to OpenWRT
build system. This utility required to manage IEE-802.15.4
devices.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
SVN-Revision: 45349
Enables last error support for the PPP protocol handlers.
In generic teardown the PPP daemon exit code is translated into
a self explaining error string which is set as interface error
by proto_notify_error in case of failure.
Signed-off-by: Johan Peeters <johan.peeters111@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 45333
The arg argument is missing to the printer call in the print_option
utility when the option flag OPT_A2STRVAL is set.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 45264
PPPD crashes (SEGV) when the dump or dryrun options are specified and an option
is internally defined as "o_special" with an option flag of "OPT_A2STRVAL".
As the option value is not saved when the parameter is processed, a reference
to the option will result into a crash (e.g. when printing).
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 45263
User might have modified/extended template direct or by LuCI application.
So do not overwrite on update/upgrade.
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 45258
This patch backports the option --tftp-no-fail to dnsmasq and prevents the
service from aborting if the specified TFTP root directory is not available;
this might be the case if TFTP files are located on external media that might
occasionally not be present at startup.
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 45213
To enable 802.11r, wpa_key_mgmt should contain FT-EAP or FT-PSK. Allow
multiple key management algorithms to make this possible.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 45050
The 802.11r implementation in hostapd uses nas_identifier as PMK-R0 Key
Holder identifier. As 802.11r can also be used with WPA Personal, nasid
should be appended to the hostapd config for all WPA types.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 45049
'hostapd-common' is needed by all of the variants for wifi to function
correctly (a number of the target profiles simply select 'wpad-mini').
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 45048
These new variants include support for mesh mode and SAE crypto.
They always depend on openssl as EC operations are not provided by
the internal crypto implementation.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45047
madwifi was dropped upstream, can't find it anywhere in OpenWrt
either, thus finally burrying madwifi.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45045
Helpful to disable when debugging lldpd crashes (when working on it).
When privilege separation is on, some crashes are stack-traced to
some privilege separation code.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 44967
from Erik Tews <erik@datenzone.de>
This patch has two effects. First, the quickleave feature/behaviour is
disabled for all groups that are used on more than one interface. The
idea of quickleave is to leave a group fast and later figure out whether
there is still somebody interested in that group. For groups used on
more than one interface, it is already known that there is still
somebody interested in that group.
Second, when a leave is received for a group that is used on more than
one interface, igmpproxy sends queries on all interface to discover
remeining listeners for that group. Previously these queries were only
send on the interface the leave was received on, so that listeners on
the other interfaces were not discovered and the group might be left on
the upstream router incorrectly.
This patch can be improved by sending the queries only on the interface
the leave was received on and adapting the algorithm in
internAgeRoute(...) in rttable.c in a way that only one interface is
actually processed and all other interfaces of the route are silently
assumed to be still active.
Signed-off-by: Erik Tews <erik@datenzone.de>
SVN-Revision: 44859
Certain DHCP servers push a gateway outside of the assigned interface subnet,
to support those situations install a host route towards the gateway.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44789
DNSMASQ has the ability to provide a menu to a pxeboot system, using
the --pxe-prompt and --pxe-service configuration options. The current
init.d script converting the "dhcp" file to "dnsmasq.conf" does not
find these options, but they are supported. This patch thus enables
the options.
Signed-off-by: Derek LaHousse <dlahouss@mtu.edu>
SVN-Revision: 44747
The --dhcp-boot option of dnsmasq does not require servername and serveraddress
arguments if the builtin tftp server is used.
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 44744
The names for the config options were taken from lldpd's
configure.ac file.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 44743
Below you'll find a patch to add ipmark module support to ipset.
Changeset 44671 already bumped ipset to version 6.24, but it's still
compiled without ipmark support. This is a requirement for mwan3 v1.6.
Signed-off-by: Jeroen Louwes <jeroen.louwes@gmail.com>
SVN-Revision: 44742
Included you'll find a patch to bump ipset to version 6.24. This
version supports the ip,fwmark set, which is needed for mwan3 1.6.
Signed-off-by: Jeroen Louwes <jeroen.louwes@gmail.com>
SVN-Revision: 44671
The wwan package holds the hotplug script to set mobile broadband
interfaces (un)available. Add it as a dependency to comgt-ncm,
uqmi and umbim.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44631
Interface should not be set unavailable in all error cases,
returning 1 is enough.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44630
Adds ncm proto to the list of checked protocols, sets interfaces
unavailable on device removal and removes the unnecessary ifup
command.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44629
USB modem data files should be a part of the wwan package, which
actually uses them unlike comgt.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44628
In a dual-WAN setup, it's useful to specify an interface over which to
have PPTP.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44507
When passing struct termios to ioctl TCGETS and TCSETS should be
used instead of TCGETA and TCSETA, which are meant for the older
struct termio. Should fix https://dev.openwrt.org/ticket/19012
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44506
This change adds the configuration options "bssid_whitelist" and
"bssid_blacklist" used to limit the AP selection of a network to a
specified (finite) set or discard certain APs.
This can be useful for environments where multiple networks operate
using the same SSID and roaming between those is not desired. It is also
useful to ignore a faulty or otherwise unwanted AP.
In many applications it is useful not just to enumerate a group of well
known access points, but to use a address/mask notation to match an
entire set of addresses (ca:ff:ee:00:00:00/ff:ff:ff:00:00:00).
This is especially useful if an OpenWrt device with two radios is used to
retransmit the same network (one in AP mode for other clients, one as STA for
the uplink); the following configuration prevents the device from associating
with itself, given that the own AP to be avoided is using the bssid
'C0:FF:EE:D0:0D:42':
config wifi-iface
option device 'radio2'
option network 'uplink'
option mode 'sta'
option ssid 'MyNetwork'
option encryption 'none'
list bssid_blacklist 'C0:FF:EE:D0:0D:42/00:FF:FF:FF:FF:FF'
This change consists of the following cherry-picked upstream commits:
b3d6a0a8259002448a29f14855d58fe0a624ab76
b83e455451a875ba233b3b8ac29aff8b62f064f2
79cd993a623e101952b81fa6a29c674cd858504f
(squashed to implement bssid_{white,black}lists)
0047306bc9ab7d46e8cc22ff9a3e876c47626473
(Add os_snprintf_error() helper)
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 44438
The recent rework of the 6in4 endpoint update broke the retry mechanism.
Rework the timeout handling and make the update status more verbose.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44327
Align init behaviour with other distros by starting an OpenVPN instance
for each config file found in /etc/openvpn/. This removes the additional
requirement to "register" the configs with uci and thus simplifies the
setup.
Make sure to respect the disabled state in uci to not suddenly autostart
instances which have been previously set to disabled, also skip configs
which are already started due to uci configuration.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44310
Busybox ash does not implement /dev/stdout, therfore any wget output
is written into a file /dev/stdout instead of onto the standard output.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44301
remove obsolete configuration settings
--disable-thread
--enable-nonblocking
--without-krb4
remove SSPI support
only supported on windows
correct --with/without-ca-path handling
only supported with OpenSSL and PolarSSL
correct LDAP/LDAPS protocol
add dependency libopenldap
added SCP/SFTP protocol
default "No"
depends on libssh2
added IDN support
default "No"
depends on libidn
added SMB protocol (new in 7.40)
default "No"
require 'cryptographic authentication' and either 'GnuTLS' or 'OpenSSL' selected
added Unix sockets support (new in 7.40)
default "No"
added error verbose messages
default "No"
changes to Makefile
Increase PKG_RELEASE
PKG_CONFIG_DEPENDS and CONFIGURE_ARGS
extended for new functionality
use "autoconf_bool" for all --enable/--disable options
restructure for easier reading
changes to Config.in
extended for new functionality
implement dependencies
restructure and grouping for easier reading
build tested on XUbuntu 14.10 x86 for x86 (generic) and ar71xx (WNDR3800)
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 44243
This patch fixes the NCM protocol by adding the missing ifname
to the netifd script and changing one unintended "send" statement to
"print" in runcommand.gcom. It also cleans up logging and makes the
manufacturer names case-insensitive. Furthermore, comgt-ncm should
not depend on the USB-serial-related kernel modules, as the cdc-wdm
control device works without them. There is also no need to depend on
kmod-huawei-cdc-ncm, since other manufacturers (like Sony-Ericsson
and Samsung) which use other kernel modules should also be supported.
I'd appreciate if someone with Samsung or Sony-Ericsson modems could
test this, I was only able to test it with Huawei E3276, E3372 and
E353.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44182
* Update to version 7.40.0
* remove non existing config options around enable/disable HTTPS protocoll
* remove --with-ca-path if ssl support disabled
* set proxy support as default like all versions before CC did
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 44176
The previous update introducing LFS support unconditionally changed the
sprintf() pattern used to print the file modification time to use PRIx64.
Explicitely convert the st_mtime member of the stat struct to uint64_t in
order to avoid type mismatch errors when building for non-64bit targets.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44138
* Fix the ubus plugin to not make its uhttpd_plugin entry symbol
constant as uhttpd needs to modify its list_head member
* Make sure that uhttpd supports large files by using 64bit ints
where appropriate and by passing _FILE_OFFSET_BITS=64 to the build
* Plug a possible memleak in the directory listing code
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44135
The previous implementation of the "host-uniq" option used plain strings for
passing the value to pppd which made it impossible to specify binary data.
Switch the format to a hex encoded string to support binary data.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44094
Extend the DHCPv4 handler script to store additional information from the
DHCP lease in the per-interface data object.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44092
Some Huawei mobile broadband sticks utilizing the NCM protocol expose
the control channel as a cdc-wdm device node instead of a virtual TTY.
This device node does not support the terminal ioctls. This patch
adds a check whether the provided device is a TTY or not and does not
attempt to use the terminal ioctls if they are not supported.
v2: reduce diffstat by simplifying code a little
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44054
This patch adds a simple check to silence logging of messages about
unrecognized igmp packets which originate from devices in local network.
Without this patch igmpproxy floods openwrt syslog with messages such as:
user.warn igmpproxy[19818]: The source address 192.168.1.175 for group
239.255.250.250, is not in any valid net for upstream VIF.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 44020
The --quiet-dhcp setting increases privacy by omitting DHCP lease logs including MAC addresses.
Signed-off-by: Lars Kruse <devel@sumpfralle.de>
SVN-Revision: 44006
Introduce configuration options to build an "hardened" OpenWRT.
Options to enable Stack-Smashing Protection, FORTIFY_SOURCE and RELRO
have been introduced.
uClibc makefile now automatically detects if SSP support is necessary.
hostapd makefile has been fixed to use "^" as sed separator since
using a comma was problematic when using "-Wl,-z,now" and the like in
TARGET_CFLAGS.
Currently enabling SSP on user space depends on enabling SSP kernel
side, this is due to the fact that TARGET_CFLAGS are used to build
kernel modules (at least). Suggestions on how to avoid this are welcome.
Using "select" instead of "depends on" doesn't seem to work with choice
entries.
Tested with a lantiq (WBMR) router, GCC 4.8, uClibc and a subset of
the available packages.
Needs to be tested with GCC 4.9 and the remaining packages.
PIE not currently included.
Signed-off-by: Alessandro Di Federico <ale+owrt@clearmind.me>
SVN-Revision: 44005
iproute2 includes "sanitized" linux kernel headers, which work fine for uClibc, however
with musl there is some header conflict, principally some ipv6 structure redefinition. This
patch removes <linux/in6.h> from include/linux/if_bridge.h to solve the problem.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 43992
This patch fixes adding new stations for some specific drivers when
using more than 1 BSS.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43951
Makes sure that the openvpn instance gets restarted in case of a crash.
Intentional stops using /etc/init.d/openvpn stop will not result in
respawning. Anything else will, e.g. killall openvpn.
Signed-off-by: Lars Gierth <larsg@systemli.org>
SVN-Revision: 43886
