Complete internal switch initialization for QCA956X.
Set default mdio device if the interface mode of GE0 is not SGMII (fix ticket #21520).
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 48937
This patch provides full GPIO support for WNR612v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48924
This patch add speed_mask parameter to Ethernet port LED initialization
during system startup. LEDs are configured to show amber light for 10 Mbps
link and green for 100 Mbps as described on device label.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48923
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48922
Enable platform-supplied WLAN LED name for ath9k device.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48879
This patch moves the OOLITE profile code into the overarching Gainstrong
profile and deletes the old single profile file.
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 48866
The ubdev01 profile defines its own MTDPARTS with smaller firmware
partition, so give it its own UBNT_BOARD in mkfwimage.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 48828
This is the first patch of a series of three to tidy up the profiles for
Gainstrong devices. Right now there are two Gainstrong profiles, each
for a single device built by this manufacturer. This patch renames the
MiniBox profile to Gainstrong and updates the copyright notice.
The series applies cleanly to current trunk. Resent with the architecture in
the subject, forgot that the first time.
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 48797
Fix for invalid/random WLAN MAC address in WNR612v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48779
Netgear WNR612v2 has no USB port yet default system image
includes USB kernel modules. This patch fixes that.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48778
Fix for invalid/random WLAN MAC address in WNR2000v3. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48777
- remove the suffix (N, ND) to indicate that the image is for all
WR841-models
- some of these models have a "N"-suffix, others have (ND)-suffix,
but the boards are the same - only difference is the detachable
antenna on "D"-models
- discussed this idea to remove the suffix in IRC with jow and Borromini
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
SVN-Revision: 48767
Netgear WNR2000v3 has no USB port yet default system image
includes USB kernel modules. This patch fixes that.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48701
This reverts commit r48276.
This can overwrite the caldata_backup partition, so the layout needs to
be changed in a different way.
Thanks to Arjen de Korte for spotting the issue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48456
According to the calling convention of the o32 ABI the caller
function must reserve stack space for $a0-$a3 registers in case
the callee needs to save its arguments.
The assembly code of the loader does not reserve stack space for
these registers thus when the 'loader_main' function needs to save
its arguments, those will be stored in the 'workspace' area instead
of the stack.
Because the workspace area is also used by other part of the code, the
saved register values gets overwritten and this often leads to failed
kernel boots.
Fix the code to reserve stack space for the registers to avoid this
error.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 48279
Change MTD on WNDR4300 and WNDR3700v4 to fully utilize the 128MB flash.
Credit to @Tuochenlyu on GitHub.
Signed-off-by: Chris Marchesi <chrism@vancluevertech.com>
SVN-Revision: 48276
Fully reset the chip like on a full up/down, but without the PHY
statemachine restart.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48228
My last bugfix (r47538) introduced a new bug in wndr3700_board_detect
(again...).
Assigning the result of ar71xx_get_mtd_offset_size_format to the model
variable before stripping of garbage using awk will cause all NUL bytes to
be removed before awk is applied, leading to model strings like
"NETGEAR WNDRMACv2NETGEAR", where a NUL byte after the v2 is supposed to
terminate the string.
Fix by calling ar71xx_get_mtd_offset_size_format twice, once piping to awk
directly.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 48075
This patch adds support for the Bitmain Antrouter R1
http://wiki.openwrt.org/toh/bitmain/r1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 48058
In r45970 the MAC swap handling was made opt-in, however some boards
have been forgotten during the conversion. Since the reference design
uses this MAC swapping, and pretty much all known boards using this chip
seem to do so too, enabling the swapping is a more reasonable default
than leaving it disabled.
Change the code to still allow boards to opt-out of this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47956
The following patch is to add ath79_register_m25p80_large, which sets
is_flash to false to support bit banging. This is needed on some 32MB+
SPI chips, such as the S25FL256S1
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47952
The MR18 stores the ath9k eeprom values on the NAND.
This patch makes it possible to retrieve the images
from there.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47948
move all library includes and 'firmware already exists'
check to the top of the script.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47947
OpenWrt configuration part of support for the PowerCloud Systems
CR5000. The CR5000 is a dual-band 802.11n wireless router with
8MB flash, 64MB RAM, (unused on stock firmware) USB 2.0 port and
five port gigabit ethernet switch. The CR5000 was sold as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47946
OpenWRt configuration part of support for the PowerCloud
Systems CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with
8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast
ethernet wan port that was sold by PowerCloud Systems as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47945
Openwrt configuration part of support for PowerCloud CAP324
Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems
who's stock firmware (CloudCommand) provides 'cloud' based managment
of large numbers access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a wall wart.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47944
Kernel part of support for the PowerCloud Systems CR5000. The
CR5000 is a dual-band 802.11n wireless router with 8MB flash,
64 MB RAM, (unused in stock firmware) USB 2.0 port, and five
port gigabit ethernet switch. The CR5000 was sold as hardware for
the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47943
Image generation part of support for PowerCloud CR3000. The CR3000 is
a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM,
a four port fast ethernet switch, and a fast ethernet wan port which
was sold by PowerCloud Systems as hardware for the Skydog
cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47942
Image generation (and mtd partition) part of support for
PowerCloud CAP324 Cloud AP. The CAP324 Cloud AP is a device sold by
PowerCloud Systems who's stock firmware (CloudCommand) provides
'cloud' based managment of large numbers of access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via
PoE or a power adaptor.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47941
Kernel part of support for the PowerCloud Systems CR5000. The
CR5000 is a dual-band 802.11n wireless router with 8MB flash,
64 MB RAM, (unused in stock firmware) USB 2.0 port, and five
port gigabit ethernet switch. The CR5000 was sold as hardware for
the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47940
Kernel part of support for PowerCloud CR3000. The CR3000 is
a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM,
a four port fast ethernet switch, and a fast ethernet wan port which
was sold by PowerCloud Systems as hardware for the Skydog
cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47939
Kernel part of support for PowerCloud CAP324 Cloud AP.
The CAP324 Cloud AP was a device sold by PowerCloud Systems as hardware for
the CloudCommand service for 'cloud' based managment of large numbers
access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a power adaptor.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47938
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47878
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
This patch just extends target/linux/ar71xx/image/Makefile to build
images also for version 2.1 of TL-WR710N
patch against the latest git
Signed off by: Norbert Wegener <nw@wegener-net.de>
SVN-Revision: 47849
The MR18 uses a 3-channel 16-bit PWM Constant Current Driver
for its status LED.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47848
Include /lib/functions/system.sh in 02_network to define missing
mtd_get_mac_binary() procedure.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47723
This removes calls to ucidef_set_interfaces_lan_wan() and
ucidef_set_interfaces_lan() on boards where all relevant info can be
inferred from the switch definition.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47722
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.
Also removes now superfluous enable and reset arguments.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47721
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.
This change ...
* removes the reset and enable arguments from ucidef_add_switch()
* unconditionally writes reset:1 and enable:1 to JSON
* converts the three users of nonstandard values to ucidef_add_switch_attr()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47720
The hwid check was wrong, causing the AR71XX_MODEL value to end with a
space (as $hwver was unset).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47553
When fixing the model string for WNDR3700v2 which contain a model string
followed by 0xff in r46455, the match for other versions of the WNDR3700v2
which just contain lots of 0xff broke (as the 0xff $model is checked for
is stripped off).
Fix by stripping off non-printable characters only for the actual output
string, but not for the internal matching.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47538
This is based on patches from Federico Fissore <f.fissore@arduino.cc>
especially this one:
7e2976fa83
The console is running with 250000 baud which is a non standard baud
rate and needs an extra patch to be applied, I will try to get this
patch upstream or something else which accomplish the same.
Some upstream code looks like there are many different versions of this
SoC, are these only internal versions and all versions on the consumer
market are the same? I saw different GPIO configuration and flash sizes
of 8MB and 16MB?
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47451
The Arduino Yun uses a baud rate of 250000 by default. The serial is
going over the Atmel ATmega and is used to connect to this chip.
Without this patch Linux wants to switch the console to 230400 Baud.
With this patch Linux will use the configured baud rate and not some
standard one which is near by.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47450
Add access to the function2 gpio register. This probably has to be
converted into a pimux driver later on. This is needed for some setup
functions on the Arduino Yun.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47449
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.
This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47420
The hardware of the v3 is identical to the v2.
Based-on-patch-by: Andreas Ziegler <github@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47406
Some devices require the kernel to be in a JFFS2 file system. Make the
support for this more generic so that it can be used by other devices.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
SVN-Revision: 47404
Incorrect value causes clock inaccuracy as huge as 1/60.
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47363
The device is similar to Archer C7 v2, but with 8M of flash, and 6 external
antennas. Reason for breaking the naming pattern is that sticker on the back
mentions "WDR7500" and has no mention of "Archer".
Signed-off-by: Srdjan Rosic <rosic@google.com>
SVN-Revision: 47344
All other tplink images use squashfs+jffs2. I don't see any reason why
this board should use squashfs-only
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47319
Observed on ar71xx/ath79 platforms such as Ubiquiti RouterStations.Reported in #20642.:
(https://dev.openwrt.org/ticket/20642).
If embedded command-line text exists with CONFIG_IMAGE_CMDLINE_HACK=y,firmware
init doesn't initialize environment pointer (fw_init_cmdline not called).
arcs_cmdline is not initialized before calling strlcat.
Signed-off-by: Ted Hess <thess@kitschensync.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 47270
The TL-WR841N/ND v10 is mostly identical to the v9. Apart from some minor
changes, it contains a newer revision of the QCA9533 SoC and the CPU clock
is significantly higher.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47263
ath9k expects to get revision id 2 for the QCA9531 ver. 2 rev. 0. This
fixes the very low TX power on some devices like the TP-LINK
TL-WR841ND v10.
As ath79_soc_rev is only used to get the revision number to ath9k on the
QCA9533, just set it to the expected value on the ver. 2.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Tested-by: Felix Kaechele <felix@kaechele.ca>
SVN-Revision: 47262
Antminers using the stock bootloader will not hash without this GPIO set.
Applies to DD and CC
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 47261
This patch fixes ticket #15267 by enabling power on the
WNR2200's USB port. At present, the USB port on the WNR2200
is non-functional due to it not receiving power.
This patch defines an additional GPIO pin, but none of the
current GPIO definitions have been modified.
Signed-off-by: Riley Baird <BM-2cVqnDuYbAU5do2DfJTrN7ZbAJ246S4XiX@bitmessage.ch>
SVN-Revision: 47236
This patch supersedes the v1 from September 17th.
Bumping the patch version - the MiniBox profile showed up under M, but
since it's called 'Gainstrong MiniBox v1.0' now it looks out of place.
Renamed the profile to gs-minibox-v1.mk to fix that.
The following patch adds support for the Gainstrong MiniBox into trunk
(or 'Designated Driver' :D ).
Fixed items:
- Inverted LED polarity (OOLITE seems to suffer from the same problem).
- Changed uppercase MINIBOX_V1_ prefix as requested.
- Prefixes are now gs_minibox_ similar to gs_oolite_ (same vendor).
- Mention the vendor (Gainstrong) in code headers.
Compiles fine, has been confirmed working by owners on 15.05.
Question: I've seen some boards use tools/firmware-utils/src/mktplinkfw.c,
the MiniBox images build fine without, so I'm wondering: do I need to add
it in there as well? Any added benefit?
Thank you
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 47234
Sets the LEDs to boardname:color:led-name
Sets the LAN to eth0
Other corrections such as the Machine Name and HWIDs
v2 corrects the profile names in the Makefile and changes tabs to spaces
in the Makefile 'define Device/' like the other devices.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 47221
* use build step mktplinkfw with extra arguments
* remove now unused mktplinkfw-chn-v2
* use Device/tplink
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47175
Allow to pass extra arguments to mktplinkfw step. Some board requires
an extra argument to create a valid image.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47174
These profiles covered by new image/Makefile descriptions. Only the old format uses
MultiProfile macro
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47173
Add support for WeIO board (http://we-io.net).
This board is based on Carambola2 board form 8Devices.
Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org> [some cleanups]
SVN-Revision: 47036
