The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
As automatic helper assignment is disabled in recent Linux kernels,
explicit rules must be added to the raw table for each helper.
While commit f50a524 in the firewall3 project added a set of default
rules and other additional related functionality, both this and the
alternative manual methods of defining these rules require kmod-ipt-raw.
Signed-off-by: Steven Honson <steven@honson.id.au>
Introduce mt76x0e device tree node in RT-AC51U dts.
Define mt76x0e mtd partition and offset
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
This was not converted to the new, dt-based board name.
Fixes: e90dc8d272 ("apm821xx: convert to device-tree board detection")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In a patch for the ath79, Mathias Kresin mentioned that
helper scripts should be in front of the device targets.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for the Netgear WNDAP620 and WNDAP660,
they are similar devices, but due to the LAN LED configuration,
the switch setup and WIFI configuration each gets a different
device target.
Hardware Highlights WNDAP620:
CPU: AMCC PowerPC APM82181 at 1000 MHz
DRAM: 128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF
CPU: AMCC PowerPC APM82181 at 1000 MHz
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE)
Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes
Hardware Highlights WNDAP660:
CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks
DRAM: 256 MB, 2 x 128 MiB DDR2
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE)
Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes
Flashing requirements:
- needs a tftp server at 192.168.1.10/serverip.
- special 8P8C(aka RJ45)<->D-SUB9 Console Cable
("Cisco Console Cable"). Note: Both WNDAP6x0 have
a MAX3232 transceivers, hence no need for any separate
CMOS/TTL level shifters.
External Antenna:
The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations:
= Config# = | = GPIO 11 = | = GPIO 14 = | ===== Description =====
1. | 1 / High | 0 / Low | Use the internal antennae (default)
2. | 0 / Low | 1 / High | Use the external antennae
The external antennaes are only meant for the 2.4 GHz band.
One-way Flashing instructions via u-boot:
0. connect the serial cable to the RJ45 Console Port
Note: This requires a poper RS232 and not a TTL/USB adaptor.
1. power up the AP and interrupt the u-boot process at
'Hit any key to stop autoboot'
2. setup serverip and ipaddr env settings
Enter the following commands into the u-boot shell
# setenv ipaddr 192.168.1.1
# setenv serverip 192.168.1.10
3. download the factory.img image to the AP
Enter the following commands into the u-boot shell
# tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img
4. verfiy image integrity
Enter the following commands into the u-boot shell
# crc32 $fileaddr $filesize
If the calculated crc32 checksum does not match, go back to step 3.
5. flash the image
Enter the following commands into the u-boot shell
# nand erase 0x110000 0x1bd0000
# nand write ${kernel_addr_r} 0x110000 ${filesize}
6. setup uboot environment
Enter the following commands into the u-boot shell
# setenv bootargs
# setenv fileaddr
# setenv filesize
# setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0'
# setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}'
# setenv bootcmd 'run owrt_boot'
# saveenv
7. boot
# run bootcmd
Booting initramfs instructions via u-boot:
Follow steps 0 - 2 from above.
3. boot initramfs
Enter the following commands into the u-boot shell
# tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin
# run addtty
# bootm ${kernel_addr_r}
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds the feature to parse the existing cpu_port DT
property, which is used to specify which port is the cpu port
of the switch.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
On the WNDAP620, the mdio and mdc lines are controlled by
the EMAC ethernet device. This results in a hen-vs-egg problem.
The rtl8367b driver is probed before the ethernet driver and
the mdio-bus is not available yet, which caused the rtl8367b
driver to fail.
This patch changes the rtl8366_smi_probe_of() function to
return -EPROBE_DEFER if the mdio-bus lookup failed and changes
rtl8366_smi_probe()'s signature to return the error code back to
the callee, so it can propagate back to the kernel. Which, will
retry the switch probe at a later time.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds u-boot environment access to the MX60(W) target.
"The environment size is one NAND block (128KiB on Buckminster).
We allocate four NAND blocks to deal with bad blocks which may
exist in the saved environment"
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All apm821xx devices use u-boot and most of them have
an accessible u-boot environment. This patch adds the
necessary template file, but does not add the
uboot-envtools package to any of the targets.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Specification:
- SoC: Qualcomm Atheros IPQ8064 ARM-v7 Dual Core SMP CPU
- RAM: 512MB DDR3 System Memory
- NOR Flash: 32MB SPI NOR
- NAND Flash: 256MB NAND
- Ethernet: 5 x 1G via QCA8337N
- USB: 2 x USB 3.0 SuperSpeed
- PCIe: 3x Mini PCIe 2.0 Slots
Three PCIE2.0 connectors can connect two or three radio cards
such as the CUS260 for 2.4 GHz WLAN and the CUS239 for 802.11ac WLAN
How to flash via u-boot console:
tftpboot 0x44000000 openwrt-ipq806x-qcom_ipq8064-ap161-squashfs-nand-factory.bin
nand erase 0x1340000 0x4000000
nand write 0x44000000 0x1340000 $filesize
setenv bootargs ‘console=ttyMSM0,115200 ubi.mtd=ubi root=/dev/ubiblock0_1’
saveenv
bootm
Further upgrades via sysupgrade.
Tested on IPQ8064 AP161 Board:
1) NAND boot
2) Tested USB and PCIe interfaces
3) WDOG test
4) cpu frequency scaling
5) ethernet, 2G and 5G WiFi
6) ubi sysupgrade
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
RouterBOARD(s) bootloader actully turns Power LED off just before
it starts the kernel. So we need to set the LED default status to On
instead of Keep in order to keep LED on during kernel boot.
This change fixes Power LED off during the kernel boot on the RB91x and
SXT Lite boards.
Fixes: 6cad8ee0bd ("ar71xx: keep the RouterBOARD Power LED in On state")
CC: Mathias Kresin <dev@kresin.me>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
This way the radio (phy) name can be the same through module reloads.
To set the desired name:
uci set wireless.@wifi-device[0].phyname=wiphy0
I guess this only works on ipq6086 boards as I could not find a more
generic place to put this. Maybe someone can improve it.
Signed-off-by: Ben Greear <greearb@candelatech.com>
If I create following image:
define Device/engenius-m36
IMAGE/sysupgrade.bin := combined-image | append-metadata
endef
Sysupgrade then errors out:
Invalid image. Contents do not match checksum (image:cd285595eaf297370404ae0e2815ec1a calculated:2cf9a2286fb6b01af3ea189128017d44)
Image check 'platform_check_image' failed.
By removing the metadata from the image I get combined-image checksum
working again and sysupgrade works.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Create initrd enries for x86 images, that'll load amd microcode as early
as possible. Also remove the preinit script responsible for late load of
microcode.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This commit adds support for the Archer C58 v1 and C59 v1, previously
supported in the ar71xx target.
CPU: Qualcomm QCA9561
RAM: 64M (C58) / 128M (C59)
FLASH: 8M (C58) / 16M (C59)
WiFi: QCA9561 bgn 3x3:3
QCA9888 nac 2x2:2
LED: Power, WiFi 2.4, WiFi 5, WAN green, WAN amber, LAN, WPS
Only C59: USB
BTN: WPS, WiFi, Reset
Installation
------------
Via Web-UI:
Update factory image via Web-UI.
Via TFTP:
Rename factory image to "tp_recovery.bin" and place it in the root-dir
of your tftp server. Configure to listen on 192.168.0.66. Power up the
router while holding down the reset-button. The router will flash itself
and reboot.
Note: For TFTP, you might need a switch between router and computer, as
link establishment might take to long.
Signed-off-by: David Bauer <mail@david-bauer.net>
The gpio-ralink driver has everything it needs to be used as an
interrupt controller except for device tree support. This simple patch
adds that support by configuring the irq domain to use two cells and
adding the appropriate documentation to the devicetree bindings.
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
this patch adds supports for GL-X750.
Specification:
- SOC: QCA9531 (650MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 10/100: 1xLAN + 10/100: 1xWAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 5x LEDS (green)
Flash instruction:
The original firmware is openwrt, so both LuCI or sysupgrade can be used.
Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
This adds the build option for UniFi AC Mesh Pro as well as
model detection for it.
The device is a hardware clone of the AC Pro.
- SoC: QCA9563-AL3A (775Mhz)
- RAM: 128MiB
- Flash: 16MiB - dual firmware partitions!
- LAN: 2x 1000M - POE+
- Wireless:
2.4G: QCA9563
5G: UniFi Chip, QCA988X compatible
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
On the bottom sticker it's branded as ZTE ZXECS EBG3130 device, but in factory
OpenWrt image it's referenced as BDCOM WAP2100-SK device.
Specifications:
- SoC: MediaTek MT7620A
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 5 FE ports
- Wireless radio: 2T2R 2.4 GHz and 1T1R 5 GHz (MT7610EN, unsupported)
- UART: 1 x UART on PCB marked as J2 (R=RX, T=TX, G=GND) with 115200 8N1 config
- LEDs: Power, FE ports 1-5, WPS, USB, RF 2.4G, RF 5G
- Other: USB port, SD card slot and 2x external antennas (non-detachable)
Flashing instructions:
A) The U-Boot has HTTP based firmware upgrade
A1) Flashing notes
We've identified so far two different batches of units, unfortunately
each batch has different U-Boot bootloader flashed with different
default environment variables, thus each batch has different IP address
for accessing web based firmware updater.
* First batch has web based bootloader IP address 1.1.1.1
* Second batch has web based bootloader IP address 192.168.1.250
In case you can't connect to either of those IPs, you can try to get
the default IP address via two methods:
A1.1) Serial console, then the IP address is visible during the boot
...
HTTP server is starting at IP: 1.1.1.1
raspi_read: from:40004 len:6
HTTP server is ready!
...
A1.2) Over telnet/SSH using this command:
root@bdcom:/# grep ipaddr= /dev/mtd0
ipaddr=1.1.1.1
A2) Flashing with browser
* Change IP address of PC to 1.1.1.2 with 255.255.255.0 netmask
* Reboot the device and try to reach web based bootloader in the
browser with the following URL http://1.1.1.1
* Quickly select the firmware sysupgrade file and click on the
`Update firmware` button, this all has to be done within 10 seconds,
bootloader doesn't wait any longer
If done correctly, the web page should show UPDATE IN PROGRESS page
with progress indicator. Once the flashing completes (it takes roughly
around 1 minute), the device will reboot to the OpenWrt firmware
A3) Flashing with curl
sudo ip addr add 1.1.1.2/24 dev eth0
curl \
--verbose \
--retry 3 \
--retry-delay 1 \
--retry-max-time 30 \
--connect-timeout 30 \
--form "firmware=@openwrt-ramips-mt7620-BDCOM-WAP2100-SK-squashfs-sysupgrade.bin" \
http://1.1.1.1
Now power on the router.
B) The U-boot is based on Ralink SDK so we can flash the firmware using UART.
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB (G=GND, R=RX, T=TX)
4. Power up the device and press 2, follow the instruction to set device and
tftp server IP address and input the firmware file name. U-boot will then load
the firmware and write it into the flash.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Create initrd enries for x86 images, that'll load intel microcode as
early as possible. To achieve that the test module for grub is enabled
which provides shell-like conditionals. Also restrict the late load of
microcode to AMD processors.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
It is not necessary to have iucode-tool present on target system to have
functional intel-microcode package. The build time dependency is kept.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Add files to bootfs image from selected as built-in packages, which want
to install files to targets boot file system.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Mount boot file system with rw option to allow installation of packages
which install files to /boot directory.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Currently every file in boot directory is copied over target /boot on
root file system and is usually inaccessible because appropriate boot
file system is mounted on top of it. Therefore remove /boot, which in
result will also save space on target root file system.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:
All future airOS versions will be signed in this way and not allow
unsigned firmware to be loaded except via TFTP.
U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:
Hit any key to stop autoboot: 0
Setting default IP 192.168.1.20
Starting TFTP server...
Receiving file from 192.168.1.25:38438
Received 4981148 bytes
Firmware check failed! (1)
By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:
Received 3735964 bytes
Firmware Version: XW.ar934x.v6.0.4-42.r8474-56aa1ac-OpenWrt
Setting U-Boot environment variables
Un-Protected 1 sectors
Erasing Flash.... done
Patch provided by AREDN[3] project, tested on Bullet M2 XW (ynezz) and
Nanostation M5 XW (ae6xe).
1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn
Signed-off-by: Petr Štetiar <ynezz@true.cz>
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART: 1 UART on PCB marked as J1 with 115200 8N1 config
LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
UART connection details
.---------------------------------.
| |
[ETH] J1 [ANT]
| o VCC o RX o TX o GND |
`---------------------------------'
Flashing instructions
A) Serial console, U-Boot and TFTP
1. Connect to serial header J1 on the PCB
2. Power on device and enter U-Boot console
3. Set up TFTP server serving an OpenWrt initramfs build
4. Load initramfs build using the command tftpboot in the U-Boot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs OpenWrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
B) Experimental factory image flashing over SSH from airOS v6.1.7
1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware
no other airOS version is currently supported
2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing
3. cd ubnt-bullet-m2hp-openwrt-flashing
4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin
Tested only on Bullet M2HP.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Belkin F5D8235 v2 has two ethernet switches on board.
One internal rt3052 and rtl8366rb on rgmii interface.
Looks like internal switch settings were lost in
translation to device tree infrastructure.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Specifically, SKW92A_E16, described here:
http://www.skylabmodule.com/wp-content/uploads/SkyLab_SKW92A_V1.04_datasheet.pdf
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x u.FL
- Power by micro-USB connector at USB1 on EVB
- UART via micro-USB connector at USB3 on EVB (57600 8n1)
- 5x Ethernet LEDs
- 1x WLAN LEDs
- 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next
to daughter board on EVB
- WPS/Reset button (S2 on EVB)
- RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board
Flash instruction:
>From Skylab firmware:
1. Associate with SKYLAP_AP
2. In a browser, load: http://10.10.10.254/
3. Username/password: admin/admin
4. In web admin interface: Administration / Upload Firmware, browse to
sysupgrade image, apply, flash will fail with a message:
Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data!
5. Telnet to 10.10.10.254, drops you into a root shell with no credentials
6. # cd /var
7. # mtd_write -r write tmpFW mtd4
Unlocking mtd4 ...
Writing from tmpFW to mtd4 ... [e]
8. When flash has completed, you will have booted into your firmware.
>From U-boot via TFTP and initramfs:
1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server
2. Connect to serial console at USB3 on EVB
3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g.
192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "1"
7. At u-boot prompts:
Input device IP (10.10.10.123) ==:192.168.11.21
Input server IP (10.10.10.3) ==:192.168.11.20
Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin
8. Move ethernet to port 0 (WAN) on EVB
9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash
with sysupgrade.
>From U-boot via TFTP direct flash:
1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server
2. Connect to serial console at USB3 on EVB (57600 8N1)
3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g.
192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "2"
7. At u-boot prompts:
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
Input device IP (10.10.10.123) ==:192.168.11.21
Input server IP (10.10.10.3) ==:192.168.11.20
Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin
8. When transfer is complete or as OpenWrt begins booting, move ethernet to
port 0 (WAN).
Signed-off-by: Russell Senior <russell@personaltelco.net>
We currently could (ab)use IMAGES for this task, but the downside is,
that the filenames has filesystem tied to the filename, which might be
confusing as the artifact itself don't has to be used with that specific
filesystem. Another downside is, that the artifacts built with IMAGES
target are build for every FILESYSTEMS filesystem.
Consider following use case:
define Device/apalis
...
FILESYSTEMS := ext4 squashfs
IMAGES := spl-uboot.bin recovery.scr
IMAGE/spl-uboot.bin := append-uboot-spl | pad-to 68k | append-uboot
IMAGE/recovery.scr := recovery-scr
endef
Where we would get target binaries with following filenames:
openwrt-imx6-apalis-squashfs.recovery.scr
openwrt-imx6-apalis-squashfs.spl-uboot.bin
openwrt-imx6-apalis-ext4.recovery.scr
openwrt-imx6-apalis-ext4.spl-uboot.bin
With proposed patch, we could now just do:
define Device/apalis
...
ARTIFACTS := spl-uboot.bin recovery.scr
ARTIFACT/spl-uboot.bin := append-uboot-spl | pad-to 68k | append-uboot
ARTIFACT/recovery.scr := recovery-scr
endef
Which would produce target binaries with following filenames:
openwrt-imx6-apalis-recovery.scr
openwrt-imx6-apalis-spl-uboot.bin
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
e520469b Update manual pages
54067256 Bump up version number to 1.35.0
c4d2eeee Update AUTHORS
f51e696e asio: Add stop() to listen_and_serve doc
a433b132 Merge pull request #1260 from nghttp2/h2load-non-final-response
cf48a56d Merge pull request #1238 from jktjkt/cmake-fix-libevent-detection
6cad1b24 nghttpx: Write mruby send_info early
3c393dca nghttpx: Fix assertion failure on mruby send_info with HTTP/1 frontend
17292445 h2load: Handle HTTP/1 non-final response
f6644a92 make clang-format
48998f72 Merge pull request #1222 from donny-dont/fix/declspec
15ff52f9 Update README
6c03bb14 Upgrade travis toolchain
524b4392 Fix travis build failure
859bf2bc Update manual pages
b5619fb1 h2load: Clarify that time for connect includes TLS handshake
dcbe0c69 nghttpx: Simplify move ctor and operator
2996c284 nghttpx: Cleanup
42e8ceb6 nghttpx: Convert API status code to enum class
1daf9ce8 nghttpx: Convert WorkerEventType to enum class
d68edf56 nghttpx: Convert MemcachedStatusCode to enum class
0c4e9fef nghttpx: Convert memcached op to enum class
571404c6 nghttpx: Convert MemcachedParseState to enum class
4d562b77 nghttpx: Convert LogFragmentType to enum class
e6225871 nghttpx: Convert connection check status to enum class
4bd075de nghttpx: Convert Http2Session state to enum class
b46a3249 nghttpx: Convert FreelistZone to enum class
4bd44b9c nghttpx: Convert dispatch state to enum class
1b42110d nghttpx: Make Downstream state enum class
0735ec55 nghttpx: Convert shrpx_connect_proto to enum class
00554779 nghttpx: Convert DNSResolverStatus to enum class
0963f389 nghttpx: Convert SerialEventType to enum class
1abfa3ca nghttpx: Make TLS handshake state enum class
f2159bc2 nghttpx: Convert UpstreamAltMode to enum class
b0eb68ee nghttpx: Convert shrpx_forwarded_node_type to enum class
e7b7b037 nghttpx: Convert shrpx_cookie_secure to enum class
5e4f434f nghttpx: Convert shrpx_session_affinity to enum class
20ea964f nghttpx: Convert shrpx_proto to enum class
d105619b src: Remove extra braces if possible
ec5729b1 Use std::make_unique
6c919695 Use C++14
46576178 Don't send Transfer-Encoding to pre-HTTP/1.1 clients
5e925f87 Update doc
153531d4 nghttpx: Use the same type as standard stream operator<<
f7287df0 Bump up version number to 1.35.0-DEV
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Some packages like libpfring assume the presense of lex, which on some
other systems is a symlink to flex but not all. Symlink flex to fix
compilation.
Arch Linux and Fedora do this as far as I know.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This is probably theoretical problem as the Ventana is defined first in
the image Makefile, but once the position of the definition would change
in the future (alphabetical sorting?) it would get bootscript from the
previous board which would have BOOT_SCRIPT set.
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Both devices come with a MediaTek MT7610E 5GHz 802.11ac 1T1R radio
which wasn't supported at the time the devices were added to OpenWrt.
Now that we got it, include kmod-mt76x0e in images for those devices.
Reported-by: Arian Sanusi <openwrt@semioptimal.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows us to use the bridge as a managed switch and gracefully
handle mixed tagged and untagged frames. Prior to this, the only
alternative was creating one bridge per vlan which quickly becomes a
nightmare and still won't let you mix both tagged and untagged frames on
the physical port without some complex ebtables magic.
This is in line with the notion that OpenWRT is the network go-to swiss
army knife when you need a nice set-and-forget, low maintenance box to
handle a specific task.
Current builds of the ip-bridge package already fully support this
feature so the only requirement is enabling the kernel config.
This is disabled by default so existing bridge configurations will not
be affected. This patch only gives the ability to turn it on with an
'ip link' command. If there is interest, I could look into making the
feature accessible via uci configuration.
It causes about 3.1% hit on raw bridging speed, which is relatively
trivial considering that I had to use 300 byte packets to strain the CPU
enough to notice a slowdown at all. The ER8 would chug along at wire
speed otherwise, and that's using only one core. Since the typical
bridge use case on OpenWRT is wireless, I doubt it would be noticeable
at all.
With BRIDGE_VLAN_FILTERING
iperf -u -c 192.168.1.105 -b 1G -l 300
------------------------------------------------------------
Client connecting to 192.168.1.105, UDP port 5001
Sending 300 byte datagrams, IPG target: 2.24 us (kalman adjust)
UDP buffer size: 208 KByte (default)
------------------------------------------------------------
[ 3] local 192.168.1.12 port 58045 connected with 192.168.1.105 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.0 sec 977 MBytes 820 Mbits/sec
[ 3] Sent 3414986 datagrams
[ 3] Server Report:
[ 3] 0.0-10.0 sec 811 MBytes 680 Mbits/sec 0.000 ms
581210/3414986 (0%)
Without BRIDGE_VLAN_FILTERING
iperf -u -c 192.168.1.105 -b 1G -l 300
------------------------------------------------------------
Client connecting to 192.168.1.105, UDP port 5001
Sending 300 byte datagrams, IPG target: 2.24 us (kalman adjust)
UDP buffer size: 208 KByte (default)
------------------------------------------------------------
[ 3] local 192.168.1.12 port 36645 connected with 192.168.1.105 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.0 sec 977 MBytes 820 Mbits/sec
[ 3] Sent 3414990 datagrams
[ 3] Server Report:
[ 3] 0.0-10.0 sec 836 MBytes 701 Mbits/sec 0.000 ms
493950/3414990 (0%)
In terms of kernel size, it uses 16KB (6753K vs 6737K on ER8) so a
0.002% hit. The exact 16KB is probably just due to how the kernel is
compressed.
Suggested-by: Jonathan Thibault <jonathan@navigue.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
