Commit graph

546 commits

Author SHA1 Message Date
Kristian Evensen
80829022b0 ramips: add support for the HNET C108
The HNET C108
(http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a
mifi based on MT7602A, which has the following specifications:

* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port. Only power is connected, this port is meant for
charging other devices.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
* 6000 mAh battery.
* 5x controllable LEDs.

Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).

Not working (also applies to the factory firmware):
* Wifi LED. It is always switched on, there is no relation to the
up/down state or activity of the wireless interface.

Not tested:
* SD card reader.

Notes:
* The C108 has no dedicated status LED. I therefore set the LAN LED as
status LED.

Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.

Recovery:
If you brick the device, the C108 supports recovery using TFTP. Keep the
reset button pressed for ~5sec when booting to trigger TFTP. Set the
address of the network interface on your machine to 10.10.10.3/24, and
rename your image file to Kernal.bin.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-09-09 09:55:13 +02:00
L. D. Pinney
3e36ca4b43 ramips: merge mt7628/mt7688 into mt76x8
The ramips subtargets of mt7628 and mt7688 dts files all #include "mt7628an.dtsi"

They are essentially a single subtarget.

This patch merges the ramips subtargets mt7628 and mt7688 into a single subtarget mt76x8.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
2017-08-30 17:05:10 +02:00
Pavel Kubelun
6e283cdc0d ramips: add Xiaomi Mi Router 3G support
This commit adds support for Xiaomi Mi WiFi Router 3G.

Short specification:
 - MT7621AT + MT7603EN + 7612EN
 - 256MB DDR3 RAM
 - 128MB NAND flash
 - 1+2 x 1000M Ethernet
 - 1x USB 3.0 port
 - reset button
 - yellow, blue, red leds

Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: mtd erase kernel0
- run: reboot

Originally stock firmware has following partitions:
 - ...
 - kernel0 (primary kernel image)
 - kernel1 (secondary kernel image, used by u-boot in failsafe routine)
 - rootfs0 (primary rootfs)
 - rootfs1 (secondary rootfs in case primary fails)
 - overlay (used as ubi overlay)

This commit squashes rootfs0, rootfs1 and overlay partitions into 1, so
it can be used by LEDE fully for package installation, resulting in 117,5MiB.

This device lacks hw watchdog, so adding softdog instead (stock does the same).

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-08-23 14:59:12 +02:00
L. D. Pinney
df3295f50e ramips: add support for the VoCore2 Lite
The VoCore2 Lite uses the same PCB as the Vocore2.
This patch moves the common VoCore2 parts into dtsi.

Removed memory node in the device tree source file.
Memory is detected automatically.

http://vocore.io/
http://vonger.net/
http://vonger.cn/

Specifications:
- SoC: MediaTek MT7688AN
- RAM: 64MB DDR2 EtronTech EM68B16CWQH-25H
- Flash: 8MB NOR SPI Flash GigaDevice GD25Q64CWIG
- Wireless: Built into MT7688AN with onboard IPEX connector

Firmware installation:
- VoCore2-Lite ships with firmware forked from OpenWrt.
- Installation from the bootloader is recommended.
- If using luci/sysupgrade use the -n option (do not keep settings)
  original firmware uses a modified proprietary MediaTek wireless driver.
- The wireless is disabled by default in LEDE.
- If reverting to factory firmware using the bootloader is recommended.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Tested by: Noble Pepper <noblepepper@gmail.com>
2017-08-11 18:12:56 +02:00
Thibaut VARENE
695f5ea85a ramips: Add support for Netgear EX3800
The Netgear EX3800 is essentially an EX3700 with a mains output socket.

Both devices use the exact same firmware image (original firmware is named
EX3700-EX3800-version.chk).

This patch adds suport by renaming the EX3700 device to EX3700/EX3800 and
updating the necessary glue.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-08-03 00:11:25 +02:00
Thibaut VARENE
8a13895a2e ramips: EX3700: rename factory.bin to factory.chk
The stock firmware upgrade interface requires the file to end with a .chk
extension.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-08-03 00:11:25 +02:00
Mathias Kresin
419fa7a15f ramips: cleanup AsiaRF AWM002 eval board support
Cleanup the dtsi files and remove one layer of dtsi. Set the size of
the firmware partition to a value matching the flash size from the
board (variant) name.

Remove the usb led trigger. There is neither a default config for the
usb led trigger nor a LED for usb activity indication.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-03 00:11:25 +02:00
Mathias Kresin
b82ac84229 ramips: drop AsiaRF AWM003 eval board
Everything is identical to the AWM002 8m eval board. No need to
duplicate it once more.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-03 00:11:25 +02:00
Mathias Kresin
861b867d9c ramips: fix Omnima MiniEMBWiFi image
Reference the Omnima MiniEMBWiFi device tree source file in the image
build code. Otherwise the dts of the image processed before is used.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-03 00:07:56 +02:00
Mathias Kresin
afc1ccf955 ramips: build HuaWei HG255D image
The code to build an image was disabled some time ago for unknown
reasons albeit the image looks fine.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-03 00:07:56 +02:00
Mathias Kresin
99f1097c0a ramips: fix Mercury MAC1200R v2.0 board name
With d2b6bf1416 ("ramips: fix image validation errors") the board
name was changed to fix an image validation error. But this change
wasn't applied to all other files using the board name, which broke
sysupgrade.

Revert this change and use the former board name in the metadata
instead.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-29 09:24:32 +02:00
Oliver Fleischmann
a92c64e8ae ramips: add support for Loewe WMDR-143N
The WMDR-143N is a small module originally used as a Wifi client
in some Loewe smart TV sets. It is sold cheaply at german surplus
shops. The module contains a RT3662 SOC.

Specifications:

- 500 MHz CPU Clock
- 1x 10/100Mbps Ethernet (pin header)
- 32 MB of RAM
- 8 MB of FLASH
- 2T3R 2.4/5 GHz (SOC internal)
- 3 Antennas on PCB
- UART pads on PCB (J3: 1 = +3.3V, 2 = RX, 3 = TX, 4 = GND), TX
  and RX are 3,3V only! The square hole is pin 1
- Power supply pads on PCB (J6: 1 and 2 = +5V, 3 and 4 = GND)
  The square hole is pin 1

The original firmware has two identical kernel/rootfs images and
two "Factory" calibration data blocks in flash. The LEDE image
leaves only the first "Factory" block in place and uses both
"Kernel" blocks and the redundant "Factory" block together to gain
enough space for the jffs2 partition.

Flash instructions:

You need UART and Ethernet connections to flash the board. Use
the LEDE "sysupgrade.bin" image with tftp.

Apply power to the board and in the first 5 seconds, hit 2 to
select TFTP upload. The bootloader asks for board- and server IP
addresses and filename.

Alternate method: With the vendor firmware running, assign an IP
address to the ethernet port, tftp the firmware image to
/tmp and write to mtd4 ("KernelA").

Signed-off-by: Oliver Fleischmann <ogf@bnv-bamberg.de>
[remove pinctrl node from dts, no pin is used as GPIO]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-27 09:13:27 +02:00
L. D. Pinney
77645ffcd9 ramips: add support for the GnuBee Personal Cloud One
The GnuBee Personal Cloud One crowdfunded on https://www.crowdsupply.com
    It is a low-cost, low-power, network-attached storage device.

    Specifications:

    - SoC: MediaTek MT7621AT
    - RAM: DDR3 512 MB
    - Flash: 32 MB
    - Six SATA ports for 2.5" Drives
    - One micro SDcard
    - One USB 3.0
    - Two USB 2.0
    - Gigabit Ethernet: 1 x WAN and 1 x LAN
    - UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
    - Four GPIOs available on a pin header

    Flash instructions:

    The GnuBee Personal Cloud One ships with libreCMC installed.
    libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
    As such one can upgrade using the webinterface or sysupgrade.

    Das U-Boot has multiple options for recovery or updates including :

    - USB
    - http
    - tftp

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use switchdev led trigger, all interfaces are in vlan1; rename leds
according to board.d setting; remove ge2 group from the pinmux, this
group doesn't exist in the driver]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-25 21:02:53 +02:00
Alex Maclean
f683385e73 ramips: add support for TP-Link RE350
The TP-Link RE350 is a wall-wart AC1200 range extender/access point with
a single gigabit ethernet port and two non-detachable antennas, based on
the MT7621A SoC with MT7603E and MT7612E radios.

Firmware wise it is very similar to the QCA based RE450.

SoC: MediaTek MT7621A (880MHz)
Flash: 8MiB (Winbond W25Q64)
RAM:   64MiB (DDR2)
Ethernet: 1x 1Gbit
Wireless: 2T2R 2.4Ghz (MT7603E) and 5GHz (MT7612E)
LEDs: Power, 2.4G, 5G (blue), WPS (red and blue), ethernet link/act
(green)
Buttons: On/off, LED, reset, WPS

Serial header at J1, 57600 8n1:
Pin 1 TX
Pin 2 RX
Pin 3 GND
Pin 4 3.3V

Factory image can be uploaded directly through the stock UI.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2017-07-25 21:02:53 +02:00
Chuanhong Guo
a4c84b2d73 ramips: add support for Phicomm K2P
It uses one MT7615D radio chip with DBDC mode enabled. This mode allows
this single chip act as an 2x2 11n radio and an 2x2 11ac radio at the
same time. However mt76 doesn't  support it currently so there is no
wireless available.

Specification:
- SoC: MediaTek MT7621AT
- Flash: 16 MB
- RAM: 128 MB
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Wireless radio: MT7615D on PCIE0
- UART: 1 x UART on PCB - 57600 8N1

Issue:
- Wireless radio doesn't work due to the lack of driver.

Flash instruction:
Using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2,then follow the instruction to
   set device and tftp server IP address and input the firmware
   file name.U-boot will then load the firmware and write it into
   the flash.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2017-07-20 19:10:29 +02:00
Matthias Schiffer
4b32d66216
ramips: simplify ubnt-erx-sfp device definition
Most of the ubnt-erx definition can be reused; the package removals in
DEVICE_PACKAGES have become redundant after d17cb4a68a "ramips: purge
default packages on MT7621".

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-06 19:45:09 +02:00
Piotr Dymacz
24043a0d2e ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.

The difference between these two models is in number of available
LEDs, buttons and power input switch.

This work is partially based on GitHub PR#974.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
  switch

* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.

Factory image notes:

These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.

We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.

Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.

The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".

Flash instruction:

Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

To access U-Boot CLI, keep pressed "4" key during boot.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Piotr Dymacz
c55fadcacb ramips: image: simplify TP-Link Archer devices definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Piotr Dymacz
5b7f592251 build: move mktplinkfw2 related commands to image-commands.mk
There are already two targets (lantiq, ramips) which use mktplinkfw2
tool for creating images. This de-duplicates code, introduces two new
build commands: tplink-v2-header, tplink-v2-image and makes use of
them in place of old, (sub)target specific ones.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Mathias Kresin
1faff3b7e3 ramips: add MT7603E driver to AFoundry EW1200
Add the MT7603E driver for the 2.4GHz wireless.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Pavlo Samko
82f9486142 ramips: add support for TRENDnet TEW-638APB V2
This patch add support for the TRENDnet TEW-638APB V2.

Specification:
- SoC: Ralink SoC RT3052F
- Flash: 4MB
- RAM: 32MB
- Ethernet: 1x LAN (100 Mbps)
- Wireless: 2.4GHz b/g/n, 2x external antenna
- Buttons: 1x Reset, 1x WPS
- LEDs: Power (green), Ethernet (green), WPS (green and orange),
  Wireless (green)
- UART: 1x UART on PCB (3.3V, GND, RX, TX) - 57600 8N1

Installation

via vendor firmware:
- upload sysupgrade.bin image

via TFTP:
- stop uboot into tftp-load into option "2"
- upload sysupgrade.bin image

Signed-off-by: Pavlo Samko <bulldozerbsg@gmail.com>
2017-06-17 15:38:19 +02:00
Sven Roederer
9715beb04c ramips: add support for Ubiquiti EdgeRouter X-SFP
This patch adds support for the Ubiquiti EdgeRouter X-SFP and
improves support for the EdgeRouter X (PoE-passthrough).

Specification:
- SoC: MediaTek MT7621AT
- Flash: 256 MiB
- RAM: 265 MiB
- Ethernet: 5 x LAN (1000 Mbps)
- UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1
- EdgeRouter X:
  - 1 x PoE-Passtrough (Eth4)
  - powered by Wallwart or passive PoE
- EdgeRouter X-SFP:
  - 5 x PoE-Out (24V, passive)
  - 1 x SFP (unknown status)
  - powered by Wallwart (24V)

Doesn't work:
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.

Installation

via vendor firmware:
- build an Initrd-image (> 3MiB) and upload the factory-image
- initrd can have luci-mod-failsafe
- flash final firmware via LuCI / sysupgrade on rebooted system

via TFTP:
- stop uboot into tftp-load into option "1"
- upload factory.bin image

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2017-06-07 06:33:33 +02:00
Filip Moc
43e4e1f4a5 Move enablemodem from ramips to new package adb-enablemodem and make it used also by TL-MR6400
Signed-off-by: Filip Moc <lede@moc6.cz>
2017-05-27 07:54:40 +02:00
Kyson Lok
abbfcc8525 ramips: add support for GL-inet GL-MT300N-V2
This patch adds supports for the GL-inet GL-MT300N-V2.

Specification:
- SoC: MediaTek MT7628AN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR
- Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps)
- USB: 1 x USB 2.0 port
- Button: 1 x switch button, 1 x reset button
- LED: 3 x LEDS (system power led is not GPIO controller)
- UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND)

Installation through Luci:
- The original firmware is LEDE, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.

Installation through bootloader webserver:
- Plug power and hold reset button until red LED blink to bright.
- Install sysupgrade image using web interface on 192.168.1.1.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
[match maximum image size with firmware partition]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-26 08:04:15 +02:00
Giuseppe Lippolis
4ba2f4dc63 DWR-512: adding wwan support for the dwr-512 3G modem
This PR allow the 3G modem embedded in the DWR-512 to be managed
by the wwan-ncm scripts. The modem will use the usb-option and
usb-cdc-ether drivers.
The DWR-512 DT is updated accordingly.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-05-25 19:01:08 +02:00
Steffen Weinreich
e71b2dad94 ramips: add om-watchdog to rut5xx DEVICE_PACKAGES
Add om-watchdog as default package for rut5xx.

Signed-off-by: Steffen Weinreich <steve@weinreich.org>
2017-05-15 22:43:33 +02:00
Ørjan Malde
5f932988c3 ramips: add support for Asus RT-AC51U
Specification:
 - SoC: MediaTek MT7620A (580 MHz)
 - RAM: 64 MiB (Winbond W9751G6JB-25)
 - Flash: 16 MiB (Spansion S25FL128SAIF00)
 - LAN: x4 100M
 - WAN: x1 100M
 - Others: USB 2.0, reset button, wps button and 9 LEDs

Issues:
 - 5 GHz band is not functional (missing driver support)

Installation:

Asus windows recovery tool:
 - install the Asus firmware restoration utility
 - unplug the router, hold the reset button while powering it on
 - release when the power LED flashes slowly
 - specify a static IP on your computer:
     IP address: 192.168.1.75;
     Subnet mask 255.255.255.0
 - Start the Asus firmware restoration utility, specify the sysupgrade
   image, and press upload

TFTP Recovery method:
 - set computer to a static ip, 192.168.1.75
 - connect computer to the LAN 1 port of the router
 - hold the reset button while powering on the router for a few seconds
 - send firmware image using a tftp client; i.e from linux:
 $ tftp
 tftp> binary
 tftp> connect 192.168.1.1
 tftp> put lede-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin
 tftp> quit

Signed-off-by: Ørjan Malde <foxyred333@gmail.com>
2017-05-10 08:45:12 +02:00
Alexey Belyaev
a7cbf59e0e ramips: add new device ZyXEL Keenetic as kn
This device exactly same as NBG-419N but with USB port and USB Led.

Specification:

- SoC: Ralink RT3052 (MIPS24Kc) @384MHz
- RAM: 32 MiB
- Flash: 8 MiB
- WLAN: WiSoC 2T2R/300Mbps (2.4GHz)
- LAN: 4x100M
- WAN: 1x100M
- USB: 1x2.0

Installation via serial console (57600 8N1) from TFTP server
 - rename the firmware to something shorter, for example
   "sysupgrade.bin" (max. 32 chars)
 - copy firmware TFTP server's directory
 - when you power on device, and see U-Boot log, immediatly push "2"
   once.
 - You will see this message:
     2: System Load Linux Kernel then write to Flash via TFTP.
        Warning!! Erase Linux in Flash then burn new one. Are you sure?
 - Push "y", and enter: device IP, then TFTP server's IP, and then
   image firmware file name.

The firmware will be downloaded within ~30 seconds and flashed to the
device (It will take about 2 minutes).

Signed-off-by: Alexey Belyaev <spider@spider.vc>
[squash commits, compact commit message, fix compatible string, remove
superfluous pinmuxes]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-10 08:45:12 +02:00
Henryk Heisig
64f2efcdff ramips: strip padding from TP-Link sysupgrade images
This reduce size of sysupgrade firmware.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-05-05 20:02:19 +02:00
Henryk Heisig
cfdd3f260e ramips: add factory firmware for Tp-Link C20i/C50
TP-Link firmware doesn't accept sysupgrade.bin with metadata.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-05-05 20:01:28 +02:00
Daniel Golle
d17cb4a68a ramips: purge default packages on MT7621
In order to have a smaller initramfs image remove all packages not
needed on all devices and add them explicitely for those actually
needing them. Also remove wpad-mini from ramips default package set
and add it to all sub-targets except for MT7621.
While at it reorder packages alphabetically and replace kmod-mt76 with
kmod-mt7603 and/or kmod-mt76x2 depending on the chip actually used on
a specific board.

Hopefully fixes FS#758

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-05-04 14:13:23 +02:00
Mathias Kresin
2ddaf96a77 ramips: add ZBT-WE826 32MB variant
The ZBT-WG826 is available with 16 or 32 MByte of flash. Split the
device tree source file, rename the currently supported 16 MByte
version and add the 32 MByte variant.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Mathias Kresin
3cfc909c54 ramips: rename Digineo AC1200 Pro to ZBT-WG3526 32MB
The Digineo AC1200 Pro is the 32MB flash variant of the ZBT-WG3526 with
unpopulated/exposed sdhci slot. Rename to board to the OEM/ODM name and
add the sdhci kernel module to use it for multiple clones.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Mathias Kresin
619d68bfc9 ramips: prepare ZBT-WG3526 for hardware variants
The ZBT-WG3526 is available with 16 or 32 MByte of flash. Rename the
current supported 16MByte version to indicate which flash size variant
is supported.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Jiawei Wang
ff258effd5 ramips: add support for ZBT-WE1326
Specification:
- SoC: MT7621AT, MT7603EN and MT7612EN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 512 MiB (EM6GE16EWXD-12H)
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Others: USB 2.0, micro SD slot, reset button and 8 x LEDs

Issues:
- Two LEDs for 2.4 GHz and 5 GHz Wi-Fi do not work, can't find GPIOs.
- The pwr LED is not GPIO controllable

How to install:
- The original firmware is OpenWrt, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.

Signed-off-by: Jiawei Wang <buaawjw@gmail.com>
2017-04-25 19:29:59 +02:00
Matthias Schiffer
411c1b64f0
ramips: update DEVICE_PACKAGES for Ubiquiti EdgeRouter X
Fixes removal of unneeded kernel modules with per-device rootfs.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-04-22 18:55:22 +02:00
Daniel Golle
f66e7cb30b ramips: add former board names to PSG1218 variants
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-04-21 14:52:46 +02:00
Mathias Kresin
9e468f7829 ramips: add former used board names to metadata
We need to keep the former used (unmodified) boardname in the metadata.
Otherwise an upgrade from an board using the old boardname will be
refused.

Fixes: a75ce960ac ("ramips: use different board names for variants")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-21 07:47:59 +02:00
Daniel Golle
c6fe325587 ramips: rename PSG1218 to match label
Fix previous commit to be less ambigous:
PSG1218 rev.A = 5 ports, external PA, heatsinks
PSG1218 rev.B = 4 ports, internal PA, no heatsinks

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-04-21 02:55:36 +02:00
Daniel Golle
c5a7dc49d1 ramips: split Phicomm PSG1218 and PSG1218K2C
PSG1218 got only 4 Ethernet ports and WAN on port 3 while
PSG1218K2C got 5 Ethernet ports and WAN on port 4
Switch to use kmod-kt76x2 instead of kmod-mt76 for both devices while
at it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-04-21 02:29:21 +02:00
Mathias Kresin
8322dba029 ramips: really drop the rt-n56u factory image
Remove the stale reference to the factory image.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 19:22:23 +02:00
Mathias Kresin
ae0facdf1d ramips: fix Netgear R6220 package selection
The Netgear R6220 requires the kmod-usb3 package and misses
kmod-usb-ledtrig-usbport package to setup the configured usb led
trigger.

Drop the already target selected kmod-mt76.

Fixes: FS#686

Fixes: 38bee61dab ("ramips: add support for Netgear R6220")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 08:18:57 +02:00
Mathias Kresin
1b5ae14162 ramips: drop rt-n56u factory image
The factory image has an uImage header covering the entire image and
not only the kernel. The original uImage header which covers only the
kernel is appended to the end of the image.

During LEDE boot the uImage rootfs splitter skips the whole filesystem,
can't find a valid filesystem magic and panics.

The last known working version was OpenWrt 14.07, which simply kept on
searching for an uImage header if the first found didn't resulted into
a working rootfs. This behaviour is kind of error prone since it could
produce false positives.

Since the sysupgrade image works fine in combination with the tftp
recovery for doing the initial installation of LEDE, simply drop the
factory image.

Related: FS#462

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 08:18:57 +02:00
Vaclav Svoboda
815cc2a69a ramips: add support for Zbtlink ZBT-WE2026
This patch adds support for the Zbtlink ZBT-WE2026.

Specification:
- SoC: MediaTek MT7620N (580MHz)
- RAM: 64 MiB
- Flash: 8 MiB SPI
- LAN: 4x100M
- WAN: 1x100M

Installation through bootloader webserver:
- With the power unplugged press and hold reset button.
- Plug power and hold reset button until LED starts to blink.
- Install sysupgrade image using web interface on 192.168.1.1.

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-17 08:58:50 +01:00
Mathias Kresin
11eac705c5 ramips: sort mt7620 image file alphabetical
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-12 09:28:19 +01:00
Joseph C. Lehner
de33a4cef0 ramips: add support for Netgear EX3700
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M

The -factory images can be flashed from the device's web
interface or via nmrpflash.

Co-authored-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-03-12 09:28:19 +01:00
Hanqing Wong
38bee61dab ramips: add support for Netgear R6220
This patch adds support for the Netgear R6220, aka Netgear AC1200 and
R6220-100NAS.

Specification:
- SoC: MediaTek MT7621ST (880 MHz)
- Falsh: 128 MiB (Macronix MX30LF1G08AA-TI)
- RAM: 128 MiB (Nanya NT5CB64M16FP-DH)
- Wireless: MediaTek MT7603EN b/g/n , MediaTek MT7612EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600

Installation through telnet:
- Copy kernel.bin and rootfs.bin to a USB flash disk, plug to usb port
  on the router.
- Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
  (login if required, default: admin password)
- You will see "Debug Enabled!"
- Telnet 192.168.1.1 and login with "root"
- ls /mnt/shares/ to find out path of your USB disk. 'myUdisk' for
  example.
- cd /mnt/shares/myUdisk
- mtd_write write rootfs.bin Rootfs
- mtd_write write kernel.bin Kernel
- reboot

nmrpflash can be used to recover to the netgear firmware if a broken
image was flashed.

Signed-off-by: Hanqing Wong <hquu@outlook.com>
2017-03-12 09:28:05 +01:00
Kristian Evensen
b11c51916c ramips: Improve Sanlinking D240 config
* The left most mini-PCIe slot (the one attached to SIM2) can be
power-cycled by setting GPIO 0 to high/low.

* The D240 only needs the MT76x2 module, so update makefile to reflect this.
Note that until the default mt7620 target is updated, then kmod-mt76 (and thus
kmod-mt7603) will be selected by default.

v2->v3:
* Indentation error.

v1->v2:
* Rename gpio and remove redundant comment (thanks Piotr Dymacz)

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-03-11 08:36:52 +01:00
Furong Xu
a93a48328d ramips: kmod-sdhci-mt7620: switch dependence to kmod-mmc
mtk-mmc/mtk_sd.ko only depends on mmc_core and mmc_block.
And, we remove kmod-sdhci dependence assignment from all related target devices.

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-03-11 08:19:37 +01:00
Joseph C. Lehner
11356e4078 ramips: remove kmod-mt76* from EX2700 images
These modules are not needed by the EX2700, since it does not
have an external wifi chip (MT7620A is covered by rt2x00).

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-03-01 22:29:57 +01:00
Francois Goudal
9b35815f0f ramips: add support for Afoundry EW-1200
This device features both a 2.4 and 5Ghz radio, and supports
802.11a/b/g/n/ac modes.
It has 5 Gb-Ethernet ports and a USB 3.0 host port.

It is powered by the Mediatek MT7621 SoC, and the MT7602E and MT7612E wifi
chipsets, together with 128MB of RAM and 16 MB of SPI Flash.

The stock firmware is in fact based on some openwrt barrier breaker, with a
mediatek SDK kernel, and an afoundry custom made web interface (not LuCI
based).
Firmware update page on the stock web interface can not accept sysupgrade
images, it bricks the device.
At this point, the only working solution I found was to connect to the
serial console port (available on J4 header) and to use opkg to install
dropbear.
Then scp the sysupgrade file in the device's /tmp and run sysupgrade from
console without preserving configuration files.

Signed-off-by: Francois Goudal <francois@goudal.net>
2017-03-01 22:29:50 +01:00
ZengFei Zhang
edae3479e6 ramips: add support for HiWiFi HC5962
This patch adds supports for the HiWiFi HC5962(gee4) http://www.hiwifi.com

Short specification:

 - MT7621AT + MT7612EN + 7603EN
 - 256MB DDR3 RAM
 - 128MB NAND flash
 - 1+3 x 1000M Ethernet
 - 1x USB 2.0 port. 1x USB 3.0 port.
 - reset button
 - UART pad on PCB (JP3: TX, RX, GND, 3.3V)

Flash instruction:

1, Download lede-ramips-mt7621-hc5962-squashfs-factory.bin
2, Login as root via SSH on 192.168.199.1 and then copy factory.bin(using wget or nc or...) to /tmp/
3, use the following commands:
   $ mtd write /tmp/lede-ramips-mt7621-hc5962-squashfs-factory.bin firmware
   $ mtd erase firmware_backup && reboot
After reboot you should be able to login as root via SSH on 192.168.1.1

Signed-off-by: ZengFei Zhang <zhangzengfei@kunteng.org>
2017-02-28 23:46:02 +01:00
Wang JiaWei
d48cc5e044 ramips: add support for HiWiFi HC5661A
HC5661A is almost the same as HC5661 but MT7628AN is used instead of MT7620A.

- MT7628AN
- 128 MiB DDR2 RAM (W971GG6KB-25)
- 16 MiB SPI NOR flash (W25Q128)
- SD slot (not work yet)
- 1+4 x 100M Ethernet
- 802.11 b/g/n Wi-Fi
- 3 x LED
- 1 x button
- UART pad on PCB (JP1: TX, RX, GND, 3.3V)

The factory flash layout seems different from HC5661.
"hwf_config" is renamed to "oem" and its size changes to 0x20000.
It is modified accordingly in the dts file.

0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "hw_panic"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000160000 : "kernel"
0x000000160000-0x000000fc0000 : "rootfs"
0x000000bb0000-0x000000fc0000 : "rootfs_data"
0x000000fc0000-0x000000fe0000 : "oem"
0x000000fe0000-0x000000ff0000 : "bdinfo"
0x000000ff0000-0x000001000000 : "backup"
0x000000050000-0x000000fc0000 : "firmware"

To install LEDE, enabled the "developer mode",
which will *void your warranty* and open the SSH server at port 1022.

sysupgrade -n -F lede-ramips-mt7628-hc5661a-squashfs-sysupgrade.bin

SD slot:
- Tried to add modules kmod-sdhci kmod-sdhci-mt7620, and corresponding dts block.
- It will block WAN + 3xLAN ports, only one LAN works.
- I'm not sure why, everything else works fine.

Signed-off-by: Wang JiaWei <buaawjw@gmail.com>
2017-02-27 11:39:31 +01:00
Joseph C. Lehner
df36b5e1b3 ramips: include only kmod-mt76-core in EX2700 image
This patch frees up flash space on the EX2700, by
removing unused mt76 drivers and firmware.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-02-26 10:26:50 +01:00
Giuseppe Lippolis
ec0f20212e ramips: added image size into dwr-512 DT
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-13 10:24:32 +01:00
Claudio Leite
290ca2ba46 ramips: fix AR670W partition alignment
mtdsplit_lzma requires that the rootfs be aligned to a block boundary.
Pad the kernel partition to make this so.

Signed-off-by: Claudio Leite <leitec@gmail.com>
2017-02-09 09:14:45 +01:00
Kristian Evensen
bb7068f26c ramips: add support for Sanlinking D240
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.

Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.

Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.

The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).

If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-02-05 22:23:28 +01:00
Joseph C. Lehner
7d00cfe9bb build: centralize fakeroot code
This patch moves the fakeroot code required by some devices to
`image-commands.mk`.

Create the fakeroot on the fly by using the undocumented -s (skip copy)
parameter of mkimage.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy
rootfs for mkimage]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-04 13:46:48 +01:00
Mathias Kresin
c1eae7a7b8 ramips: fix Airlink AR725W device title
Gemtek is the ODM but the board was sold by Airlink101.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-04 13:46:48 +01:00
Mathias Kresin
1ba7fa652c ramips: fix Airlink AR725W factory image build
The factory image can't be bigger than 3328 KByte. If the image is
bigger than that, the gemtek-header tool throws an error and breaks
the build.

Make sure the output file to which the gemtek header should be added
exists and wasn't removed during the check-size step because of it
size. This will prevent hard errors in case the factory image is to big
similar to what is done for sysupgrade images.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-04 13:46:48 +01:00
Tobias Wolf
bf2f09c005 ramips: Introduce CONFIG_MIPS_APPENDED_RAW_DTB to F5D8235 V1 (rt288x)
This activates the CONFIG_MIPS_APPENDED_RAW_DTB kernel configuration and
configures the F5D8235 V1 target to use append-dtb for kernel creation
instead of OWRTDTB.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
[Jo-Philipp Wich: rewrap commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-02 00:13:49 +01:00
FUKAUMI Naoki
6b0b526a4f ramips: add support for Buffalo WCR-1166DS
Buffalo WCR-1166DS is a small wireless router with

 - MT7628AN + MT7612E
 - 64MiB DDR2 SDRAM
 - 16MiB SPI flash
 - 2T2R 11ac/a/b/g/n Wi-Fi
 - 2x 10/100M ethernet switch
 - 8x programmable LED
 - 3x button
 - UART pad on PCB (J2: 3.3V, GND, TX, RX)

factory image can be installed via stock web UI.

due to the "dual image" function in the bootloader, the second half of
the SPI flash ("firmware2" partition) cannot be used as a part of the
file system.

Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2017-01-31 11:10:58 +01:00
Joseph C. Lehner
f93a121533 ramips: cleanup mt7620 Netgear image code
1. Reuse functions defined in `image-commands.mk`
2. Rename fakeroot image

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-01-27 11:10:10 +01:00
Vitaly Chekryzhev
0352cc6b19 ramips: ZyXEL Keenetic Viva: align factory images
ZyXEL web-flasher requires squashfs to be aligned to 64kb.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-01-26 16:39:08 +01:00
Yo Abe
21b4625135 ramips: add ip17xx support to WLI-TX4-AG300N
ramips/rt288x WLI-TX4-AG300N was missing support for its 100Mbit switch which
should be included by default.

Signed-off-by: Yo Abe <abe.geel@gmail.com>
[Jo-Philipp Wich: picked from OpenWrt PR#359, rewrap commit msg, fix Sob]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-26 14:41:31 +01:00
Vitaly Chekryzhev
65985e9ace ramips: ZyXEL Keenetic Omni align factory images
ZyXEL web-flasher requires squashfs to be aligned to 64kb.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-01-20 00:39:30 +01:00
Thibaut VARENE
7fb11c8ed2 ramips: add support for Netgear WN3000RPv3
This patch adds support for the Netgear WN3000RPv3
http://www.netgear.com/support/product/wn3000rpv3.aspx

Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Serial: JP1 header, 57600-8N1
- Stock firmware based on OpenWRT Kamikaze

Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This is why the same fakeroot image is used for the WN3000

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-01-18 12:06:16 +01:00
Rosen Penev
7967178cfc ramips: Add back sdhci-mt7620 driver to default config
The driver no longer causes kernel panics and CPU hangs.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-01-18 08:54:53 +01:00
Lazar Demin
ab90f15c89 ramips: Added Onion Omega2 and Omega2+
This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)

Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
  - RAM: 64MB DDR
  - Storage: 16MB NOR SPI flash onboard
- Omega2+
  - RAM: 128MB DDR
  - Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
  - All Docks Provide:
    - Micro-USB port to provide power to the Omega
      - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
    - USB 2.0 socket connected to Omega
  - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
    - Omega GPIO breakout
    - Allows for connection of Omega Expansions:
      - Ethernet Expansion
      - Relay Expansion
      - PWM Expansion
      - OLED Expansion
      - Ethernet Expansion
      - Proto Expansion
      - Cellular Expansion

Signed-off-by: Lazar Demin <lazar@onion.io>
2017-01-15 17:43:14 +01:00
Rosen Penev
80768ddccd ramips: Add I2C driver to the default kernel config
I made a commit that added the RTC driver to the kernel config with
the intent that it would fix hctosys. Unfortunately while the RTC
driver is in there, it's connected through I2C, the driver for which
comes in module form and is thus loaded late. After this commit, it
works fine.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-01-15 17:43:05 +01:00
Andrew Yong
3f31029b19 ramips: add support for VoCore2
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.

Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
            boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
  - USB 2.0 socket
  - MicroSD socket
  - 100Mbps Ethernet x1
  - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
    DAC/ADC (support WIP)
  - Micro USB for power and console (UART2)

Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
  SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
  original firmware uses Ralink SDK Wi-Fi drivers and not
  mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
  Ethernet or the micro USB console to configure Wi-Fi again

Signed-off-by: Andrew Yong <me@ndoo.sg>
2017-01-13 08:32:35 +01:00
Felix Fietkau
84bd74057f build: use mkhash to replace various quirky md5sum/openssl calls
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-05 11:09:12 +01:00
Rafał Miłecki
939ef157da ramips: fix NixcoreX1 profiles
There was a typo in Makefile that prevented using these profiles.

Fixes: a75ce960ac ("ramips: use different board names for variants")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-12-28 23:05:24 +01:00
Mathias Kresin
0cf581ca3a ramips: use new image build code for more devices
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
a75ce960ac ramips: use different board names for variants
Use different names for flash size related board variants, to make sure
that only images for the actual flash size are considered as valid by
the image validation code.

Remove the flash size suffix from the string returned by
ramips_board_detect() to ensure that existing scripts relying on the
former used boardname are still working.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
29f5e643ad ramips: sort rt305x image file alphabetical
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
d2b1148e75 ramips: use D-Link DIR-600 B1 image for B2 version
Everything set for the B1 is identical to the values uses for the B2
version.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
d2b6bf1416 ramips: fix image validation errors
The name from the Device define will be used in the metadata. Due to
typos/different spelling, this name might not match the one exported in
/lib/ramips.sh.

Fix all name mismatches which were found by checking if the name used
in the metadata exists in /lib/ramips.sh.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Henryk Heisig
4f033b2da6 ramips: fix tplink image building fix sysupgrade firmware on MR200
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-24 06:52:12 +01:00
Henryk Heisig
c8043137bb ramips: Add support to TP-Link Archer MR200
CPU: MT7620N 580MHz
Flash: 8MB
RAM: 64MB
build-in modem 3G/4G
four ethernet port 10/100Mbps

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-22 15:03:30 +01:00
Vitaly Chekryzhev
190ee7d86b ramips: add support for ZyXEL Keenetic Omni / Omni II
Factory image can be installed via Zyxel WebUI.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2016-12-22 15:03:13 +01:00
Tobias Wolf
2e020e2cef ramips: add support for PCI based OHCI/EHCI support for F5D8235 V1
This router uses an PCI attached NEC EHCI controller to support the single USB port.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2016-12-04 07:03:17 +01:00
Mathias Kresin
4780e7e994 ramips: add size checks/append metadata where missing
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:34:23 +01:00
Mathias Kresin
6cc0ae27b9 ramips: fix Airlink AR670W factory image
Move the mkwrgimg build step to the makefile. It will be required by
other boards as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:34:23 +01:00
Mathias Kresin
ee6beb2e1c ramips: remove kmod-ledtrig-usbdev from recently added devices
None of the devices uses an usb led at all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-24 22:37:40 +01:00
Giuseppe Lippolis
ec1de9b1a6 ramips: Add device DLINK DWR-512-B
The Dlink DWR-512-B modem is a ralink 5350 processor based embedding
a 3G mini-pcie router.

The oem JBOOT bootloader has to be replaced by a RT5350 SDK
U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot
configured for the RT5350 256MiB SDR.

Main reason to change the bootloader is the encrypted header used to
store the kernel image. In this way an image can only be generated
using the propietary binboy tool (included in the GPL distribution
from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs
partition scheme. This is considered a big constraint (limited kernel
size and inefficient usage of flash space).

For interested people I pubblished the details of my investigation
about the encrypted firmware header here:
http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2016-11-23 08:36:11 +01:00
Mathias Kresin
8f561c6516 ramips: do not append metadata to CY-SWR1100 factory image
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-23 08:36:11 +01:00
Mathias Kresin
18e7f49975 ramips: order mt7621.mk alphabetical
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-23 07:09:03 +01:00
perillamint
68634426fe ramips: add support for WeVO W2914NS v2
Signed-off-by: Yong-hyu Ban <perillamint@gentoo.moe>
2016-11-21 10:13:17 +01:00
Felix Fietkau
478f1f6b16 ramips: append metadata to images
metadata checks are not enforced yet, because some images are still
being built by legacy code

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-19 11:24:10 +01:00
Vitaly Chekryzhev
348344874c ramips: add support for ZyXEL Keenetic Viva
Factory image can be installed via Zyxel WebUI.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-18 08:54:57 +01:00
Jasper Scholte
3d680c5728 ramips: add support for Sitecom WLR-6000
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.

The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.

The stock firmware uses the following mac addresses:

LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5:   00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)

Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:

2.4GHz: 00:0C:F6:AA:BB:D8
LAN:    00:0C:F6:AA:BB:D9
WAN:    00:0C:F6:AA:BB:DA
5 GHz:  00:0C:F6:AA:BB:DC

The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.

There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.

Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.

Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-17 06:39:52 +01:00
Dominik Menke
8b65fef173 ramips: add support for Digineo AC1200 Pro
This is basically a ZBT-WG3526 (mt7621 SoC), but with 32M flash.

Signed-off-by: Dominik Menke <dom@digineo.de>
2016-11-17 06:39:52 +01:00
Roger Pueyo Centelles
5f6e948551 ramips: Add support for Wavlink WL-WN575A3
This commit adds support for the Wavlink WL-WN575A3, a dual-band wall-plug
wireless router with the following specifications:

 - CPU: MediaTek MT7628AN 580MHz
 - Flash: 8MB
 - RAM: 64MB
 - Ethernet: 2x 10/100 Mbps (switched)
 - 2.4 GHz: 802.11b/g/n SoC, MIMO 2x2, 20 dBm
 - 5 GHz: 802.11a/n/ac MT7612E, MIMO 2x2, 20 dBm
 - Antennas: 4x external (2 per radio), non-detachable
 - LEDs: 4 programmable + LAN, WAN, POWER
 - Buttons: reset, WPS

Flashing instructions:

Factory U-boot launches a TFTP client if WPS button is pressed during power-on.
Rename the sysupgrade file and configure a TFTP as follows:

 - Client (WL-WN575A3) IP: 192.168.10.101
 - Server IP: 192.168.10.100
 - Filename: firmware.bin

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2016-11-08 11:17:10 +01:00
BangLang Huang
bc4109845d ramips: fix Newifi D1 profile
the images were generated for the wrong flash size.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-11-08 11:17:10 +01:00
Andrew Yong
faf94d926e ramips: add support for MikroTik hEX v3 (RB750Gr3)
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).

RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.

Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.

The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.

A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-02 10:25:44 +01:00
Stijn Segers
eefe07ef4d ramips: add usb packages into DIR-860L B1 profile
This patch adds the kmod-usb3 and kmod-usb-ledtrig-usbport packages to the
DIR-860L B1 profile. The DIR-860L B1 has a USB 3 port.

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-11-02 10:25:44 +01:00
Rosen Penev
369884c2a1 ramips: Add RTC driver to kernel for working hctosys
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2016-10-31 16:41:26 +01:00
Rafał Miłecki
0658527e1e switch to the new usbport LED trigger
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:09:45 +02:00
YuheiOKAWA
4050cfebda ramips: add support for Planex VR500.
SOC:	MT7621A
RAM:	256MiB
NOR:	MX25L51245G

Non Wireless Router.

Issue: soft reboot problem. SPI Flash do not exit 4byte address mode.

Signed-off-by: Yuhei Okawa <tochiro.srchack@gmail.com>
2016-10-15 11:36:51 +02:00
Mathias Kresin
0a219c8dfb ramips: use rootfs splitter and new image build code for BR-6475ND
Use the edimax uImage splitter instead of the fixed size rootfs
partition.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
e7ec5df33b ramips: move edimax images to the new build code
Images installed via TFTP recovery or the Edimax webinterface of the
3g-6200n(l) are writting with the edimax header to flash.

Use only one image type for these boards. The migration to the
factory only images need to be done via TFTP recovery.

Use the same start address for the 3g-6200n(l) factory images as the
stock firmware images.

Thanks to Jan Dostrasil for reporting all the issues of the 3g-6200nl
and the patient testing of all changes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Klaus
df5416296c ramips: add support for Zyxel NBG-419N2 (WAP3205v2)
applied bb-final-ramips-add-zyxel-nbg-419n2.patch from
123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65;
see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905,
modified slightly to fit to CC release and to new lede build
system: image/rt305x.mk include file is used now
changed NBG-419N2.dts format to fit style of other dts files

Signed-off-by: Klaus <k-laus@quantentunnel.de>
2016-10-04 11:50:51 +02:00
Xuefu Lin
dce5c4f5c8 ramips: Add support for Phicomm K2 PSG1218
- CPU: MT7620A 580MHz
- Flash: 8MB - RAM: 64MB
- External PA+LNA on both WLAN2.4 and WLAN5
- 4x LAN ethernet and 1x WAN ethernet

Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
2016-10-04 11:50:46 +02:00
BangLang Huang
142ec7ada9 ramips : add support for Newifi D1
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-09-27 17:50:22 +02:00
BangLang Huang
9fe833e1d0 ramips : add support for PandoraBox D1
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-09-27 17:50:22 +02:00
Cezary Jackiewicz
66aae9a271 ramips: Add support for ZBT-CPE102
- CPU: MT7620N 580MHz
- Flash: 8MB
- RAM: 64MB
- build-in minipcie slot for modem 3G/4G
- one ethernet port 10/100Mbps

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-09-27 17:50:21 +02:00
Matthias Schiffer
43bf3e80b2
ramips: fix DEVICE_PACKAGES of Ubiquiti EdgeRouter X
kmod-rt2x00-lib and kmod-mac80211 need to be removed, as they depend on
kmod-cfg80211. kmod-rt2800-pci should not be installed anyways.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-26 17:57:57 +02:00
Mathias Kresin
eb88a9cacb ramips: fix wrong blocksizes
The D-Link DIR-860L B1 has a flash chip which doesn't support
4K sectors. Since the DIR-860L B1 was the only mt7621 board which had
the 4k blocksize set, the 4K sector support is removed from the kernel
config.

I've checked the flash chips of all boards having set a 4K blocksize
again. This time I searched harder to finding bootlogs instead of
relying on wikis articles and/or the device tree source file.

The Planex MZK-DP150N has an en25q32b instead of the mentioned one in
the dts. Albeit the en25q32b supports 4K sectors, 4K support is not
enabled in the driver. Change the blocksize for this board back to 64K.

Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-15 09:53:37 +02:00
Mathias Kresin
1cd0a4c688 image: add KERNEL_SIZE to the default device vars
This reverts commit ec37a56587 and fixes
the underlying issue.
2016-09-13 19:36:41 +02:00
Felix Fietkau
d27bce8d28 build: drop UBI EOF marker from images by default
Only add them where they are actually required.
Should help with compatibility issues with stock U-Boot images that
access UBI

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-12 18:21:52 +02:00
Mathias Kresin
7d9ef9080c ramips: set blocksize for remaining rt3883 devices
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-08 21:03:57 +02:00
Mathias Kresin
9f531efc59 ramips: remove old build code seama recipe
Now that all seama images are using the new build code this seama recipe
used with the old build code can be dropped.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 15:27:46 +02:00
Mathias Kresin
fb39b77ccb ramips: switch DIR-610 A1 to new image build code
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-08 22:21:23 +02:00
Mathias Kresin
bd39104e95 ramips: switch some rt3883 devices to new build code
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 10:18:31 +02:00
Mathias Kresin
0f3600ccee ramips: move seama build recipe to Makefile
The identical build step is defined twice. Move it to the parent
Makefile to use only one version.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 09:43:31 +02:00
Mathias Kresin
74da44cfc2 ramips: switch DIR-615 H1 to new image build code
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-02 07:34:36 +02:00
Mathias Kresin
483fd5f6ad ramips: add build recipe for senao header
Add it to the Makefile to allow a board which will be supported soon
to use the recipe as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-17 07:49:34 +02:00
Mathias Kresin
28110727f1 ramips: set blocksize for 4MB devices
Set the blocksize for devices having only 4MB of flash for ramips
devices already using the new image build code.

Informations about the used flash chip are gathered from the OpenWrt
wiki, wikidevi, forums, OEM bootlogs or the compatible property in the
device tree source file.

The en25q32b from the AirLive Air3GII does not have 4k support in the
kernel.

For the following boards no information about the used flash chip could
be found and a 64k blocksize is assumed:

  - Ralink V11ST-FE
  - Ralink AP-RT3052-V22RW-2X2
  - MediaTek MT7628 EVB
  - MediaTek MT7621 EVB
  - UPVEL UR-326N4G
  - Buffalo WZR-AGL300NH

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 09:56:35 +02:00
Mathias Kresin
05ab2323ff ramips: don't set the same max image size twice
The ralink_default_fw_size_8M is already set for the default device.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-04 10:04:20 +02:00
Mathias Kresin
a499d0a6b5 image: specify max image size in Kilobyte/Megabyte
Use the k and m unit suffix to be consistent with the blocksize.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-04 09:58:02 +02:00
Mathias Kresin
e7ec7a08aa image: use k as unit suffix for blocksize
Use k as unit suffix for kilobyte to have a the same unit regardless of
the used filesystem.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-04 08:56:05 +02:00
Mathias Kresin
5369a03d52 ramips: use lower case names for TEW-69xGR images
Use lower case variant of the device name for to images to be
consistent with all other images names.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-09 07:12:37 +02:00
Mathias Kresin
775f93e898 ramips: fix wrong TARGET_DEVICES
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-08 23:51:46 +02:00
Mathias Kresin
034c5cb820 ramips: fix wrong device title
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-08 07:32:00 +02:00
Daniel Golle
083ef3fefe ramips: add support for Mercury MAC1200R v2
MT7628AN + MT7612E, 8MB SPI flash, 64MB DDR RAM
reset button GPIO is still missing (anyone?)
bootloader password is 'slp'

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2016-09-09 02:38:06 +02:00
Felix Fietkau
358cd6d9eb ramips: fix legacy initramfs images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-03 10:47:42 +02:00
Mathias Kresin
c9e6b173f7 ramips: fix build of TRENDnet TEW-69xGR images
The image generation for TEW-691GR and TEW-692GR was broken since
79d02229 due to the move of the UMedia recipe to another Makefile.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-20 11:47:25 +02:00
Mathias Kresin
c892f37b30 ramips: move umedia build step to Makefile
Some rt3883 based boards need this one as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-20 11:47:25 +02:00
Felix Fietkau
592c0a1cd2 ramips: fix legacy image build
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-08-11 17:07:37 +02:00
Chuanhong Guo
0f73801f4f ramips: Add support for Thunder Timecloud
Thunder Timecloud is a small NAS with MT7621A. It has 1 USB port and an
SD Card slot. There is no wireless cards.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2016-08-10 03:04:08 +02:00
Jimmy Zhong
2b1f4945b1 ramips: Add support for TEW-714TRU
Signed-off-by: Jimmy Zhong <mb300sd@mb300sd.net>
2016-08-10 03:03:50 +02:00
John Crispin
8e75630d1d ramips: updated remaining profiles to the new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-08-03 15:30:13 +02:00
Felix Fietkau
63b525dd6b image: add a helper variable for getting kernel/rootfs from within image Build/* templates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-31 12:25:25 +02:00
Jo-Philipp Wich
db49dd894e build: rename sysupgrade-nand to sysupgrade-tar
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-07-29 16:53:03 +02:00
Michael Lee
c3e420f28c ramips: Add support for D-Link DCH-M225
D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash,
3.5mm audio out support. but no ethernet and usb ports.
so you must default enable wifi.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
L. D. Pinney
cf8c77be6b ramips: Add support for the NixCore X1 Module
The NixCore X1 is a Ralink/MediaTek rt5350 WiFi Module.

http://nixcores.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Drew Gaylo <drew@nixcores.com>
2016-07-11 14:19:47 +02:00
Felix Fietkau
201dbb9fe8 ramips: fix build error in ubnt-erx initramfs factory image
Build initramfs kernel image, but skip factory image if initramfs size
is too big.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-06 10:12:37 +02:00
John Crispin
d09f0045ea ramips: fix up switch settings for Sitecom WL-351 v1 002
Pinmux for rgmii needs to be set to rgmii, not gpio.
Hide the ESW switch on boot (using new rgmii esw devicetree attribute).
Also add a Sitecom-specific profile, since the image needs to include
the rtl8366 kernel driver.

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
2016-07-03 08:00:26 +02:00
Roger Pueyo Centelles
5fba0f0c0c ramips: add suport for ZBT APE522II
The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has
64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with
802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac
MT7612E-based 5 GHz radio.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2016-06-22 19:32:06 +02:00
Henryk Heisig
01fb393c67 ramips/image: Add Archer C50 to mt7620 Makefile
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-06-13 22:51:43 +02:00
Michael Lee
9a4935687d ramips: add support for DuZun DM06
DuZun DM06 is a develop board based on mt7628
64M RAM, 8M SPI Flash, 1 WAN, 1 LAN.
wm8960 codec with line out, line in and speaker output.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:43 +02:00
Joseph C. Lehner
065de8bd7a ramips: fix Netgear EX2700 images
Calling `cat foo bar | dd ... conv=sync` *may* add
extraneous padding. Avoid this.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2016-06-05 23:23:57 +02:00
Joseph C. Lehner
8b0fbd8e70 ramips: rebrand Netgear EX2700 fakeroot uImage
Change image name: "OpenWrt fakeroot" -> "LEDE fakeroot"

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2016-06-05 23:23:57 +02:00
Yuan Chenmang
b38296f2f6 ramips: add Widora-NEO board support
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.

Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-01 12:52:28 +02:00
Joseph C. Lehner
2a589539ba ramips: fix Netgear EX2700 images
The previous image creation code would have failed if the
unpadded kernel uImage size was less than 64 bytes from the
next erase block boundary. Fix that.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2016-05-30 22:52:59 +02:00
Joseph C. Lehner
b232669d45 ramips: fix Netgear EX2700 images
The bootloader on this device expects the kernel partition to end
on a 64k boundary. The last 64 byte of the kernel partition must
contain a valid uImage header (the fakeroot partition).

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2016-05-27 15:50:18 +02:00
John Crispin
2a6b899589 ramips: fix 8M WT3020 image creation
fix image size for 8M version : 4M -> 8M

Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
2016-05-16 20:59:06 +02:00
John Crispin
1d9c0b2409 ramips: fix ArcherC20i image creation - 3rd try
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-15 11:59:43 +02:00
Felix Fietkau
ce009d16a1 ramips: fix Archer C20i image build
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-15 14:11:26 +02:00