These patches add support for configuring ath9k based devices via
devicetree. This was tested on PCI(e) based devices. This should work
for AHB based devices as well (adding more AHB specific properties may
still be needed) as soon as the ath79 platform is ready to populate the
ath9k wmac via devicetree.
This patchset was accepted upstream, more information can be found on
the linux-wireless list:
https://www.spinics.net/lists/linux-wireless/msg155474.html
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Without setting the HSR to the selected channel, the WLAN of the UAP
Outdoor+ will exhibit high packet loss in RX.
Based-on-patch-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport upstream accepted patch which allows to override the EEPROM
mac address with one from device tree.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The patch 615-rt2x00-fix_20mhz_clk.patch fixes code introduced by
611-rt2x00-rf_vals-rt3352-xtal20.patch and makes the the platform data
property clk_is_20mhz obsolete.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Most of the lantiq devices with ralink wifi have the EEPROM stored
in big endian byte order in flash, but the driver expects the EEPROM to
be in little endian.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The ralink,mtd-eeprom device tree property doesn't require the
ralink,eeprom property to work.
Rework the error handling and user notification as well. Do not log an
error if the mtd-eeprom parameter isn't used. It could be intentional
and should not scare the user.
Check if the number of bytes read from the mtd devices matches the
requested number of bytes.
In case of an mtd read error, give a hint to the user which partition
was tried to read from.
In case everything is fine, notify the user as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Call the rt2x00lib_get_eeprom_file_name only once and from the function
where the EEPROM filename is required.
Error only out if an EEPROM file is mandatory. Use the
REQUIRE_EEPROM_FILE bit to determine if it is mandatory.
Do not set the REQUIRE_EEPROM_FILE bit while requesting an EEPROM file.
It should be (and is) set before requesting an EEPROM file.
Do not redirect users to upstream while using a function of a custom
patch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit efd9dec319.
ath10k can take a long time to probe, long enough for netifd to fail to
initialize already configured wireless devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
LEDE no longer requires all PHYs to be initialized to
create the configuration files during bootup. This patch
removes the now obsolete ath10k patch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Adds the latest patches from Jes Sorensen for rtl8xxxu, which improve
rtl8732bu, rtl8192eu and rtl8188eu support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This fixes bug that could cause WARNING on every add_key/del_key call.
It also replaces WARNING with a simple message. They may still occur
e.g. on station going out of range and A-MPDU stall in the firmware.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
All these patches are in wireless-drirvers-next. There is support for
hidden SSID, few new devices and many fixes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
power save response frames can go through the old tx path, and the tid
needs to be set for sequence numbers to be assigned correctly.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit 31e5ed4152.
I've noticed some weird powersave related issues with this commit.
Revert until they've been fixed.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To work correctly hostapd requires wireless driver to allow interfaces
removal. It was working with brcmfmac only partially. Firmware for
BCM43602 got some special hack (feature?) that allowed removing all
interfaces by disabling mbss mode. It wasn't working with BCM4366
firmware and remaining interfaces were preventing hostapd from starting
again.
Those patches add support for "interface_remove" firmware method which
works with BCM4366 firmware and they make it finally possible to use
BCM4366 & brcmfmac & multiple interfaces.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
This allows gpiolib to re-use ath9k's devicetree node as GPIO
controller.
Example:
ath9k: ath9k@0 {
#gpio-cells = <2>;
gpio-controller;
}
Now the ath9k node can be used just like any other GPIO controller:
gpios = <&ath9k 1 GPIO_ACTIVE_HIGH>;
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This enables ath9k's built-in GPIO controller for all chip versions
(instead of an explicit whitelist). This also allows us to get rid of
some duplicate code between hw.c and gpio.c because hw.c already
determines the number of GPIOs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This folds 550-ath9k_add_ar9280_gpio_chip.patch into
548-ath9k_enable_gpio_chip.patch because the former patch only extends
code which is introduced in the latter.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
The PDU length of incoming LLC frames is set to the total skb payload size
in __ieee80211_data_to_8023() of net/wireless/util.c which incorrectly
includes the length of the IEEE 802.11 header.
The resulting LLC frame header has a too large PDU length, causing the
llc_fixup_skb() function of net/llc/llc_input.c to reject the incoming
skb, effectively breaking STP.
Solve the problem by properly substracting the IEEE 802.11 frame header size
from the PDU length, allowing the LLC processor to pick up the incoming
control messages.
Special thanks to Gerry Rozema for tracking down the regression and proposing
a suitable patch.
Fixes FS#24.
References:
https://bugs.lede-project.org/index.php?do=details&task_id=24
Reported-by: Gerry Rozema <gerryr@rozeware.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This makes brcmfmac compatible with mac80211 which uses dev_alloc_name
(and so returns -ENFILE on error).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
The patch 300-ath9k-force-rx_clear-when-disabling-rx.patch broke TX99 support
in ath9k. Fix the patch by only applying rx_clear if TX99 mode is not used.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Enable access to GPIO on Atheros wireless chip AR9280.
Support for 9280 is added to existing 9285/9287 subsystem
because these 3 chips differ only in number of GPIO pins.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49251
This prepares brcmfmac for better country handling and fixes BCM4360
support which was always failing with:
[ 13.249195] brcmfmac: brcmf_pcie_download_fw_nvram: FW failed to initialize
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48959
Enable access to GPIO chip and its pins for Atheros AR92xx
wireless devices. For now AR9285 and AR9287 are supported.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48881
Support default state for platform LEDs connected to ath9k device.
Now LEDs are correctly set on or off at ath9k module initialization.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48880
Enable platform-supplied WLAN LED name for ath9k device.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48879
It's not really supported yet as it still fails with:
brcmfmac: brcmf_pcie_download_fw_nvram: FW failed to initialize
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48640
llid_in_use needs to be limited to stations of the same VIF, otherwise it
will cause a NULL deref as the sta_info of non-mesh-VIFs don't have
sta->mesh set.
Steps to reproduce:
modprobe mac80211_hwsim channels=2
iw phy phy0 interface add ibss0 type ibss
iw phy phy0 interface add mesh0 type mp
iw phy phy1 interface add ibss1 type ibss
iw phy phy1 interface add mesh1 type mp
ip link set ibss0 up
ip link set mesh0 up
ip link set ibss1 up
ip link set mesh1 up
iw dev ibss0 ibss join foo 2412
iw dev ibss1 ibss join foo 2412
# Ensure that ibss0 and ibss1 are actually associated; I often need to
# leave and join the cell on ibss1 a second time.
iw dev mesh0 mesh join bar
iw dev mesh1 mesh join bar # crash
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47364
This patch fix https://lists.openwrt.org/pipermail/openwrt-devel/
2015-August/034979.html. As the peak detect calibration is set
incorrectly.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46948
So far support for multiple interface was somehow broken in brcmfmac.
Driver couldn't correctly match firmware and system interfaces resulting
in not working APs and WARNINGs. This pending patches fixes that :)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46734
We sill don't use kernel 4.2 which is required for backporting using
upstream NVRAM support patch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46724
