Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
It's required to support devices using adjustable SoC pins for some
specific purpose (e.g. I2C, PWM, UART1).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Instead of reverting whole commit it's enough to just revert a single
line change. It seems the real problem with the regressing commit was a
bump of read chunk size. Switching back to 256 B chunks is enough to fix
the problem/regression.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
only thing not working is the b43 5GHz wifi band as upstream
kernel
doesn't supporthe 0x4360 chip so far
Signed-off-by: Rene Kjellerup <rk.katana.steel@gmail.com>
That upstream commit caused instability in flash reads. It was reported
but there isn't any proper fix as for now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This includes Linksys EA9500 support, BCM53573 timer fix and
upstream-ready partitions patch that replaces two downstream hacks.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
USB 3.0 PHY is attached to the MDIO bus and should be supported
(accessed) as a MDIO device. This wasn't known initially which resulted
in writing driver that was working with MDIO bus (using some magic
values) without knowing it.
This commit updates DT to properly describe MDIO & USB 3.0 PHY and
enables required kernel drivers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Support for these devices isn't ready yet and it was only accidentally
pushed in the commit 0da9303e5b ("mac80211: backport "brcmfmac:
cleanup and some rework" from 4.17").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It was described by Arend as:
> This series is intended for 4.17 and includes following:
>
> * rework bus layer attach code.
> * remove duplicate variable declaration.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes missing rootfs on above device:
[ 2.652292] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
(...)
[ 2.687909] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Fixes: 05cb6aa69f ("bcm53xx: replace linux,part-probe with a proper partitions subnode")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
This switches bcm53xx from spi-bcm53xx to the spi-bcm-qspi driver. The
later one was developed by Broadcom and is more advanced one. It
supports more modes, setting a speed, setting bits per word and uses
IRQs instead of polling.
This increases kernel size from 1808120 B to the 1811160 B (by 3040 B).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is important fix for flash parsing in some corner cases. In case
of TRX subpartition with rootfs being aligned to the flash block size it
was incorrectly registered twice. Detecting & registering it as a
standalone partition was resulting in an incorrect "firmware" partition
size and possibly broken sysupgrade.
It wasn't noticed before because "rootfs" alignment depends on a kernel
size. It can happen though - depending on the configuration and the
kernel size.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
There are few symbol changes but only 3 symbols were possible to set:
THERMAL_EMERGENCY_POWEROFF_DELAY_MS
CLK_BCM_SR
PHY_NS2_USB_DRD
Both new drivers don't seem to apply to Northstar so they are disabled.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Right patch version this time, sorry!
* Patch 180-usb-xhci-add-support-for-performing-fake-doorbell.patch had to be adjusted slightly because of upstream adapted code.
* Refreshed patches.
Compile-tested: ramips/mt7621, x86/64
Run-tested: ramips/mt7621, x86/64
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
This bumps the 4.4. kernel in master to 4.4.119.
Includes more Meltdown & Spectre mitigation.
* Refresh patches.
* Refresh x86/config for RETPOLINE.
* Deleted 8049-PCI-layerscape-Add-fsl-ls2085a-pcie-compatible-ID.patch (accepted upstream)
* Deleted 8050-PCI-layerscape-Fix-MSG-TLP-drop-setting.patch (accepted upstream)
* Deleted 650-pppoe_header_pad.patch (does not apply anymore (code was replaced)).
Bumps from 4.4.112 to 4.4.115 were handled by Kevin Darbyshire-Bryant.
Compile-tested on: ar71xx & oxnas.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
This patch bumps the 4.14 kernel to .23.
- Refreshed patches.
- Deleted bcm53xx/patches-4.14/089-PCI-iproc-Fix-NULL-pointer-dereference-for-BCMA.patch. Has been accepted upstream.
- Deleted generic/pending-4.14/821-usb-Remove-annoying-warning-about-bogus-URB.patch. The upstream URB code was changed,
the patch no longer applies. I discussed this with the patch author and removed it for now, we'll see how it goes.
Compile-tested on: ramips/mt7621, x86/64
Run-tested on: ramips/mt7621, x86/64
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Looking for a wrong LED file name was stopping this code from find any
LED. This affects devices with only a red/amber power LED.
Fixes: 3aaee1ba02 ("bcm53xx: failsafe support")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This solution is more upstream compatible as it only requires specifying
of_match_table in the parser code and doesn't depend on linux,part-probe
which is solution made generic by a LEDE downstream patch that can't be
upstreamed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>