This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.
In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.
0x50000 0xe80000 0xff0000
+-------------------------------+--------------+
| rootfs | kernel |
| (14528k) | (1472k) |
+-------------------------------+--------------+
After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.
0x50000 0xff0000
+----------------------------------------------+
| firmware |
| (16000k) |
+----------------------------------------------+
However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".
This commit requires new flash instruction instead of the old one.
Flash instruction using initramfs image:
1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
/dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
fw_setenv ipaddr 192.168.12.1
fw_setenv serverip 192.168.12.10
fw_setenv ethaddr 00:aa:bb:cc:dd:ee
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing
And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Currently every file in boot directory is copied over target /boot on
root file system and is usually inaccessible because appropriate boot
file system is mounted on top of it. Therefore remove /boot, which in
result will also save space on target root file system.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
We currently could (ab)use IMAGES for this task, but the downside is,
that the filenames has filesystem tied to the filename, which might be
confusing as the artifact itself don't has to be used with that specific
filesystem. Another downside is, that the artifacts built with IMAGES
target are build for every FILESYSTEMS filesystem.
Consider following use case:
define Device/apalis
...
FILESYSTEMS := ext4 squashfs
IMAGES := spl-uboot.bin recovery.scr
IMAGE/spl-uboot.bin := append-uboot-spl | pad-to 68k | append-uboot
IMAGE/recovery.scr := recovery-scr
endef
Where we would get target binaries with following filenames:
openwrt-imx6-apalis-squashfs.recovery.scr
openwrt-imx6-apalis-squashfs.spl-uboot.bin
openwrt-imx6-apalis-ext4.recovery.scr
openwrt-imx6-apalis-ext4.spl-uboot.bin
With proposed patch, we could now just do:
define Device/apalis
...
ARTIFACTS := spl-uboot.bin recovery.scr
ARTIFACT/spl-uboot.bin := append-uboot-spl | pad-to 68k | append-uboot
ARTIFACT/recovery.scr := recovery-scr
endef
Which would produce target binaries with following filenames:
openwrt-imx6-apalis-recovery.scr
openwrt-imx6-apalis-spl-uboot.bin
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
The -rcX "testing" kernels are no longer hosted on
cdn.kernel.org file servers directly in a "testing"
directory. Therefore the logic that tested for "-rc"
can be removed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Refreshed all patches.
Altered patches:
- 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch
New symbol for arm targets:
- HARDEN_BRANCH_PREDICTOR
Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Add a basic variant which provides WPA-PSK only, 802.11r and 802.11w and
is intended to support 11r & 11w (subject to driver support) out of the
box.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The tl-wa850re-v2 images from the ar71xx/tiny target are getting too big
with the default packages. The size check is done before the meta data
is added so there is no file to add meta data to or to sign. Originally
errors in Build/append-metadata were getting ignored, but if the signing
fails the error is not ignored.
This adds a check if the file to be signed is there and only does the
signing if it is there. This way it does not fail if the package
creation was already aborted earlier.
Fixes: 848b455d2e ("image: use ucert to append signature")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sometimes, the CMakeLists.txt file is not in the root directory of a
repo. In those cases, the CMAKE_SOURCE_SUBDIR variable can be specified
to use CMakeLists.txt from a subdirectory instead.
Signed-off-by: Amol Bhave <ambhave@fb.com>
Refreshed all patches.
Added new patch:
- 192-Revert-ubifs-xattr-Don-t-operate-on-deleted-inodes.patch
This fixes a bug introduced in upstream 4.14.68 which caused targets using
ubifs to produce file-system errors on boot, rendering them useless.
Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The current make-ras.sh image generation script for the ZyXEL NBG6617
has portability issues with bash. Because of this, factory images are
currently not built correctly by the OpenWRT buildbots.
This commit replaces the make-ras.sh by C-written mkrasimage.
The new mkrasimage is also compatible with other ZyXEL devices using
the ras image-format.
This is not tested with the NBG6616 but it correctly builds the
header for ZyXEL factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
