Commit graph

20049 commits

Author SHA1 Message Date
Rinki Kumari
dd02a19ff5
ar71xx: fix TP-Link Archer C7 v5 switch LEDs
Signed-off-by: Rinki Kumari <rinki13@gmail.com>
2018-11-17 16:27:38 +01:00
Pau Escrich
15f16bf05b ar71xx: add support for Gainstrong MiniBox V3.2
Adds MiniBox V3.2 ar71xx target (QCA99531 + QCA9887)
Info: http://oolite.cn/minibox-v3-2-qca9531-qca9887-module-pin-specification.html
Reference patch: http://oolite.cn/wp-content/uploads/2017/09/minibox_v3_cc15.05_20160325.patch
Installation: Upload firmware to uboot via HTTP at 192.168.1.1 (press button for 5 seconds)

Signed-off-by: Pau Escrich <p4u@dabax.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(daniel@makrotopia.org: rebased and fixed conflicts, fixed LED name,
                        added ath10k eeprom)
2018-11-15 19:49:51 +01:00
Rafał Miłecki
c6a1bcac16 kernel: fix ubifs loosing O_TMPFILE data after power cut
There was a bug in ubifs related to the O_TMPFILE. When reapplying
changes after power cut data could be lost. This problem was exposed by
overlayfs and the upstream commit 3a1e819b4e80 ("ovl: store file handle
of lower inode on copy up").

This fixes a regression introduced when switching from 4.9 to 4.14.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-15 12:32:20 +01:00
Koen Vandeputte
e14dc93073 kernel: bump 4.14 to 4.14.81
Refreshed all patches.

Removed upstreamed patches:
- 081-spi-bcm-qspi-switch-back-to-reading-flash-using-smal.patch

Altered patches:
- 0054-cpufreq-dt-Handle-OPP-voltage-adjust-events

Compile-tested on: cns3xxx, imx6, ipq806x, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-14 16:27:43 +01:00
Koen Vandeputte
7e20e4ab96 kernel: bump 4.9 to 4.9.137
Refreshed all patches.

Removed upstreamed hunks in:
- 703-phy-support-layerscape.patch

Compile-tested on: ar71xx, layerscape
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-14 16:27:43 +01:00
Koen Vandeputte
f7a406deaf kernel: bump 3.18 to 3.18.125
Refreshed all patches.

Compile-tested on: adm5120
Compile-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-14 16:27:43 +01:00
Stijn Tintel
e95e9fcbb2 kernel: bump 4.14 to 4.14.80
Refresh patches.

Compile-tested: ar71xx, ath79, x86/64
Runtime-tested: ar71xx, ath79, x86/64

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-11-13 00:44:01 +02:00
Rafał Miłecki
0cf32de17c bcm53xx: add DT patch describing pins mux controller
It's needed to support new devices that use specific pin functions.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-09 22:29:16 +01:00
Rafał Miłecki
c7c4ae35d6 kernel: deprecate support for the generic "linux,part-probe" DT binding
It has been rejected upstream and instead a nice/more generic solution
has been implemented. It's possible now to describe partitions format
using "compatible" DT string.

No OpenWrt target uses "linux,part-probe" anymore, leave it only in case
some forks need it. It will be dropped with support for new kernels.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-09 14:57:45 +01:00
Rafał Miłecki
9a3c805584 ramips: use separated mtd patch reverting write_page() removal
This helps understanding mtd changes needed to get downstream NAND
driver working.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-09 13:31:47 +01:00
Rafał Miłecki
f975ab8f4e bcm53xx: update pinctrl driver
It's upstream now with a one trivial fix.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-09 07:41:36 +01:00
Daniel Golle
217fe505b6 oxnas: remove superseded sysupgrade image check
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-11-08 14:41:42 +01:00
Daniel Golle
b831eb5363 oxnas: kd20: correct memory size to 256MB
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-11-08 14:41:42 +01:00
Koen Vandeputte
b4e17a7440 ramips: fix netgear r6120 factory image generation
as indicated in commit c5bf408ed6 "(ramips: fix image generation for mt76x8")
more rework was needed to fix the other issues.

Building on another machine, but using the same arch, showed
the application failing again for different reasons.

Fix this by completely rewriting the application, fixing following found issues:

- buffer overflows, resulting in stack corruption
- flaws in memory requirement calculations (too small, too large)
- memory leaks
- missing bounds checking on string handling
- non-reproducable images, by using unitilized memory in checksum calculation
- missing error handling, resulting in succes on specific image errors
- endianness errors when building on BE machines
- various minor build warnings
- documentation did not match the code actions (header item locations)
- allowing input to be decimal, hex or octal now

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-08 13:32:22 +01:00
Felix Fietkau
b318edb999 ramips: add missing DTS frequency limit for the 5 GHz radio on Archer C20i
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-06 22:25:49 +01:00
Koen Vandeputte
74738c4b80 imx6: fix DMA transaction errors
Following errors were seen in the past on imx6 when using serial:

[ 22.617622] imx-uart 2020000.serial: DMA transaction error.
[ 22.623228] imx-uart 2020000.serial: DMA transaction error.
[ 22.628826] imx-uart 2020000.serial: DMA transaction error.
[ 22.648951] imx-uart 2020000.serial: DMA transaction error.
[ 22.654558] imx-uart 2020000.serial: DMA transaction error.
[ 22.660156] imx-uart 2020000.serial: DMA transaction error.

Which is the reason why DMA for the serial ports
got disabled in commits:

efb362cd93 ("imx6: disable dma on uart")
3b4241071d ("imx6: disable UART dma")

As indicated on mailinglist discussion, the cause seems to be
the usage of very old SDMA firmware which is present in the soc:

[    0.624302] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[    0.624318] imx-sdma 20ec000.sdma: Falling back to user helper
[   64.531607] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware

This patch adds the new firmware binary. (2196 bytes)

It is required to embed the binary into the kernel image, as it
gets loaded very early in the boot process where the rootfs is not
available yet:

[    0.622966] imx-sdma 20ec000.sdma: loaded firmware 3.3

Extended testing shows that the DMA errors are not seen anymore
when using this newer firmware version.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-06 11:49:27 +01:00
Koen Vandeputte
860de2e1aa ar71xx: disable some tiny targets with kernel 4.14
The bump to kernel 4.14 caused a massive increase in kernel size.

For most targets, switching them to dynamic partitioning allowed
to cope with this.

On some targets, the kernel partition is located behind the rootfs,
which disallows switching to dynamic partitioning as the boot location
would be altered, requiring a u-boot change.

Also within the tiny section, which disables kernel symbols etc
to decrease the image size,  the partition size is still too small.

Disable these targets for now, fixing image generation:

- Buffalo BHR-4GRV2
- Zbtlink ZBT-WE1526

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-05 16:00:06 +01:00
Koen Vandeputte
c764b2b531 kernel: bump 4.14 to 4.14.79
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-05 16:00:00 +01:00
David Bauer
5896b146a4 ipq40xx: fix NBG6617 LED mapping
The NBG6617's LEDs are wrongly identified in the 01_leds boardinit
script (board instead of boardname), resulting in referencing
non-existent LEDs in UCI.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-11-05 02:30:00 +00:00
Daniel Golle
9bcc08958b oxnas: add console=ttyS0,115200 argument to bootargs
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-11-04 21:43:37 +01:00
Daniel Golle
cf7896117b oxnas: enable image metadata by setting SUPPORTED_DEVICES
For each board, set the legacy name as well as the new based on the
compatible-string from devicetree.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-11-04 21:43:37 +01:00
Daniel Golle
ef9b169df0 oxnas: remove stray kernel config symbols
CONFIG_CRYPTO_* shouldn't be set by the target

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-11-04 21:43:36 +01:00
Daniel Golle
4f017c871d oxnas: switch to generic board detect
remove /lib/oxnas.sh platform-specific board-detection and use
generic which is based on device-tree compatible node instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-11-04 21:43:36 +01:00
Martin Weinelt
0411813c6f
ramips: fix leds on GL.iNet GL-MT300N-V2
The WAN LED now shows the link state. It's color is green,
not blue.

Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
2018-11-02 21:43:15 +01:00
Christian Lamparter
dceee8cc09 ipq-wifi: drop custom board-2.bins
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and linux-firmware.git.

We switched to the upstream board-2.bin, hence the files can be removed
here.

Keep the ipq-wifi package in case new boards are added. It might take
some time till board-2.bins send upstream are merged.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-01 17:16:53 +01:00
Christian Lamparter
8b18fce3b8 ipq40xx: nbg6617: switch to upstream boardfile variant
The NBG6617's boardfile was merged and this device can
now switch to the upstream ath10k board-2.bin.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-01 17:16:53 +01:00
Christian Lamparter
6840f15a16 ipq40xx: rt-ac58u: replace ubi auto load hack
This patch replaces the custom autoload quirk of the
RT-AC58U with a bootargs-append overwrite.

The vendor's u-boot doesn't leave the bootargs / cmdline alone,
so the it can't be overwritten in any other way right now...
And of course, this will be a lot of fun to deal with once
the device switches to the new spi-nand subsystem.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-01 17:16:52 +01:00
Koen Vandeputte
162e016fed ar71xx: expand kernel size for ubnt targets
Kernel 4.14 is pretty large causing a build error as the partition is too small.
Expand the kernel partition a bit to make it fit.

* ubnt-uap-pro
* ubnt-unifi-outdoor-plus

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-29 16:20:47 +01:00
Koen Vandeputte
d6b63f1698 ar71xx: disable ap91-5g due to kernel size
This target causes a build failure as the kernel image does not fit
into the kernel partition.

As the kernel is located behind the rootfs, it cannot be enlarged
as the boot entry location would get altered.

Disable this target for now.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-29 16:20:47 +01:00
Koen Vandeputte
7c78be1b74 ar71xx: switch more targets to dynamic partitioning
Targets:
- TP-LINK ER355
- TP-LINK C25 V1
- TP-LINK C59 V1
- TP-LINK C7 V4
- TP-LINK C7 V5

Fixes build issues seen due to the kernel being too big

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-29 11:21:23 +01:00
Radek Dostál
9d35b68776 ar71xx: switch TP-Link RE450 v1 to dynamic partitioning
As mentioned in commit 5f24933 recent changes on ar71xx (switch to 4.14,
memory compaction, ...) cause an increase in kernel size, making it too
big for RE450.

RE450 images were not build due to the following error message:
os-image partition too big (more than 1572864 bytes): Success

Tested on RE450, device boots and was used to send this patch.

Reported-by: Enrico Mioso <mrkiko.rs@gmail.com>
Suggested-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[rewrote commit msg keeping it tight + fixed SoB lines]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-29 11:21:23 +01:00
David Bauer
f89fc43a50 ar71xx: move OCEDO Koala to generic and use dynamic partitioning
This changes the OCEDO Koala flash-layout to a unified firmware
partition, thus making the ar71xx-generic kernel fit in flash.

Compile and runtested on OCEDO Koala.

Signed-off-by: David Bauer <mail@david-bauer.net>
[small title reword]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-29 11:21:23 +01:00
Mathias Kresin
374e646724 ath79: fix PQI Air Pen support
Use the correct dts filename. It has to be <soc>_<manufacturer>_<device>.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-28 11:03:49 +01:00
YuheiOKAWA
27eae6597e ath79: add support for PQI Air Pen
SoC: AR9330 (or AR9331 revision?)
Ethernet x1, Wireless 2.4G, uSD card slot x1.
USB Power, include Li-Po Battery.

Flash 8MiB. (factory is dual image)
1. write image is use half 4MiB size from factory.
  write initramfs image to mtd6 and mtd7.
2. change next boot setting. next is mtd6 boot.
  echo -ne "\x01" | dd of=/dev/mtdblock8 conv=notrunc bs=1 count=1 seek=0

3. rewrite sysupgrade image.
  change next boot setting. next is mtd4.
  echo -ne "\x00" | dd of=/dev/mtdblock8 conv=notrunc bs=1 count=1 seek=0

OEM mtd.
dev:    size   erasesize  name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00010000 00010000 "ART"
mtd3: 00010000 00010000 "NVRAM"
mtd4: 00140000 00010000 "uImage"
mtd5: 00280000 00010000 "rootfs"
mtd6: 00140000 00010000 "uImage2"
mtd7: 00280000 00010000 "rootfs2"
mtd8: 00010000 00010000 "CONF"

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
2018-10-28 10:59:14 +01:00
Roger Pueyo Centelles
23f9b2d9a9 ath79: Add support for Ubiquiti LiteAP ac (LAP-120)
This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor
5 GHz AC access point with an integrated 120° 16 dBi antenna. The device
was previously known as LiteBeam AP ac but was later rebranded.

CPU:    Atheros AR9342 SoC
RAM:    64 MB DDR2
Flash:  16 MB NOR SPI
Ports:  1 GbE port (PoE in)
WLAN:   5 GHz QCA899X (PCI)

The integrated QCA899X is a Ubiquiti branded part with modified vendor
and product id (0777:11ac9). It is very similar to the NanoStation loco
AC, except for the 2.4 GHz management radio (missing here).

Installation procedure is the same as the NanoStation [loco] AC:

1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-10-28 10:59:09 +01:00
Koen Vandeputte
5f298b95a1 kernel: add missing symbol for target bcm53xx
Fixes: ca88f4153f ("kernel: bump 4.14 to 4.14.77")

Reported-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-23 10:57:02 +02:00
Rafał Miłecki
9b385b2496 bcm53xx: use upstream SPI controller fix
This just moves patch to use 0xx prefix and includes maintainer's s-o-b.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-10-23 09:43:08 +02:00
Koen Vandeputte
bc3d47cd12 kernel: bump 4.14 to 4.14.78
Refreshed all patches.

Remove upstreamed:
- 050-net-emac-fix-fixed-link-setup-for-the-RTL8363SB-swit.patch

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-22 15:28:31 +02:00
Koen Vandeputte
9c42391c0d kernel: bump 4.9 to 4.9.135
Refreshed all patches.

Fixes:
- CVE-2018-10883

Compile-tested on: ar71xx, layerscape
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-22 15:28:31 +02:00
Ryan Mounce
4d2613b01a mpc85xx: workaround 4.14 cross compile issue
Regression introduced with 4.10 by 43c9127d94d62a232ed33ed2eab8a08657ce5472

Build will fail if system 'ar' does not support deterministic builds.
e.g. macOS with Xcode toolchain

Appears to be fixed upstream in 4.18 by af3901cbbd3de182aafb8ee553c825c0074df6a2

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2018-10-20 16:24:29 +02:00
Christian Lamparter
fc70276e6c apm821xx: add disk-activity triggers via DT.
The WNDR4700 and the MBL have a dedicated HDD activity LED.
This patch adds the default led triggers to the DTS and
removes the entries in 01_leds.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-10-20 16:13:39 +02:00
Christian Lamparter
1d5d77612f apm821xx: apm82181.dtsi overhaul
- order entries by mmio address where possible

 - switch to lower-case address values

 - comment on BSP u-boot behaviour in regards to
   what it edits and look for

 - annotate irq lines with the help of interrupt-names

 - remove deprecated "device_type" properties
   The pci and network device_type had to stay since
   they are required by the drivers and u-boot.
   the cpu and memory device_types will remain as well
   as they are still part of the DT Spec.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-10-20 16:13:39 +02:00
Christian Lamparter
9ca82c2374 apm821xx: force WNDR4700 console to 115200n8
With the upcoming 4.19 release, the serial console on the
Netgear WNDR4700 would no longer work as it is never really
set and always relied on the kernel's serial code not to
change the baud rate.

On the stock firmware, Netgear forced the console setting
through a custom CONFIG_CMDLINE in their kernel to 115200.
Normally, they should have done it in a different way and
just passed the baudrate through a "console=..." kernel
parameter via the bootargs in the "/chosen" dt node.
But in their default u-boot bootcmd setting, they somehow
forgot to add the "run addtty", so there's no easy way to
pass the baudrate from u-boot to the kernel. So it has
to be forced as otherwise it ends up as 9600 baud.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-10-20 16:13:39 +02:00
Christian Lamparter
68bb91018d apm821xx: set uart compatible to ns16750
The APM821XX/PPC460EX datasheet mentions:
"Register compatibility with 16750 register set"

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-10-20 16:13:39 +02:00
Linus Walleij
f280bd7fa8 gemini: Fix up image generation
I noticed that the image generator for the Gemini generates
some 10+ MB files for the second (application) partition.
This is just wrong. The first 6144K partition named initramfs
easily fits OpenWRTs squashfs,jffs2 overlayed partitions
with nice headroom for storing configuration files.

Generate a blank partition for the hddapp.tgz file and delete
it after generating the firmware image - when performing
updates manually you just want the "rd.z" file around
anyways.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-10-20 16:13:39 +02:00
Linus Walleij
10ec966f7b gemini: Break out USB to packages
This creates a new kernel package for the fotg210 host
controller and uses that with the gemini to shrink the
kernel. The SQ201 needs the USB2 PCI package as well.

The build system required me to make kernel_oldconfig
beofore it would build without errors so some minor
unrelated Kconfig entries are changed.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-10-20 16:13:39 +02:00
Baptiste Jonglez
b2c68ceea7 kernel: Add support for Winbond w25q128jv SPI NOR flash
Newer batches of several Mikrotik boards contain this yet-unsupported
flash chip, for instance:

- rb941-2nd (hAP lite)
- rb952ui-5ac2nd (hAP ac lite)
- RBM33G

and probably other Mikrotik boards need this patch as well.

The patch was submitted upstream by Robert Marko: https://patchwork.ozlabs.org/patch/934181/

Closes: FS#1715
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Cc: Robert Marko <robimarko@gmail.com>
2018-10-20 16:13:39 +02:00
Koen Vandeputte
ca88f4153f kernel: bump 4.14 to 4.14.77
Refreshed all patches.

Altered patches:
- 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch

New symbol for arm targets:
- HARDEN_BRANCH_PREDICTOR

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-19 10:01:57 +02:00
Koen Vandeputte
6d682d82b0 kernel: bump 4.9 to 4.9.134
Refreshed all patches.

Compile-tested on: ar71xx, layerscape
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-19 10:01:57 +02:00
Fabio Bettoni
ddc11c3932 ar71xx/ath79: fix mtd corruption
In commit fec8fe8069 ("kernel: bump 4.9 to 4.9.116") [1], the following patch for removed:
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch

This patch contained fixes for both write and erase functions.

While the chip-detects for erase got fixed upstream [2],
some modifications are still required, even with the fixes applied.

While at it, also apply the same fix for target ath79,
which suffers the same issue.

Not doing so results in following errors seen:

Collected errors:
 * pkg_write_filelist: Failed to open //usr/lib/opkg/info/luci-lib-ip.list: I/O error.
 * opkg_install_pkg: Failed to extract data files for luci-lib-ip. Package debris may remain!
 * opkg_install_cmd: Cannot install package luci-ssl.
 * opkg_conf_write_status_files: Can't open status file //usr/lib/opkg/status: I/O error.

[    0.780920] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    8.406396] jffs2: notice: (415) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    8.423476] mount_root: switching to jffs2 overlay
[  270.902671] jffs2: Write of 1989 bytes at 0x005ce6f8 failed. returned -5, retlen 962
[  270.931965] jffs2: Write of 1989 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.939631] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[  270.950397] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.957838] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[  270.968584] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.976027] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[  270.986735] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.994225] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero

[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=fec8fe806963c96a6506c2aebc3572d3a11f285f
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.9.133&id=a0239d83e1cb60de5e78452d4708c083b9e3dcbe

Fixes: fec8fe8069 ("kernel: bump 4.9 to 4.9.116")
Signed-off-by: Fabio Bettoni <fbettoni@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-17 18:55:37 +02:00