In order to have a smaller initramfs image remove all packages not
needed on all devices and add them explicitely for those actually
needing them. Also remove wpad-mini from ramips default package set
and add it to all sub-targets except for MT7621.
While at it reorder packages alphabetically and replace kmod-mt76 with
kmod-mt7603 and/or kmod-mt76x2 depending on the chip actually used on
a specific board.
Hopefully fixes FS#758
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
I made a commit that added the RTC driver to the kernel config with
the intent that it would fix hctosys. Unfortunately while the RTC
driver is in there, it's connected through I2C, the driver for which
comes in module form and is thus loaded late. After this commit, it
works fine.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The D-Link DIR-860L B1 has a flash chip which doesn't support
4K sectors. Since the DIR-860L B1 was the only mt7621 board which had
the 4k blocksize set, the 4K sector support is removed from the kernel
config.
I've checked the flash chips of all boards having set a 4K blocksize
again. This time I searched harder to finding bootlogs instead of
relying on wikis articles and/or the device tree source file.
The Planex MZK-DP150N has an en25q32b instead of the mentioned one in
the dts. Albeit the en25q32b supports 4K sectors, 4K support is not
enabled in the driver. Change the blocksize for this board back to 64K.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is a follow up to 28110727f1
"ramips: set blocksize for 4MB devices". I've missed to include the
required changes of the kernel configs to enable 4K sector size
support.
The option is only enabled for targets having boards with 4k sector
size flash chips.
Signed-off-by: Mathias Kresin <dev@kresin.me>
1004kc is just a SMP capable 34kc, and GCC treats 24kc and 34kc exactly
the same and will generate identical code, so there is no need to tune
to 1004kc instead of 24kc.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
There does not seem to be any meaningful difference in generated code.
This will save some time and space on snapshot builds
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- Use default number of uarts (2) for rt288x/rt305x/rt3883/mt7620.
- Allow up to 3 uarts on MT7621 and MT7628.
- Remove unneeded SERIAL_8250_RT288X for MT7628.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.
v1->v2:
* Remove some references to 2626 that I had missed in the dts.
v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
SVN-Revision: 49213
Remove unnecessary packages to reduce image size so it fits in initramfs (to enable upgrading from factory firmware).
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49127
This router is based on MT7621 SoC, no wifi, no usb, nand.
Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.
Doesn't work:
* No GPIO leds. All leds are controlled by switch,
but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
nand/spi drivers do not support pin sharing,
so it is not accessable and disabled. Stock
firmware could read it and it was empty.
* PoE out.
Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.
U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.
Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47881
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47875
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.
This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 47845
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47843
Enables CPS multiprocessing instead ob obsoleted CMP for mt7621.
This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx:
* iperf shows only 50Mbits on direct gigabit connection to desktop,
* ping times jump to 5-6ms to dorectly connected desktop
* /proc/interrupts shows spurious interrups (ERR)
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47842
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
this device only works on top of UBI.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade
Tested and not working
* failsafe
Signed-off-by: YounJae Rho <luxflow@live.com>
SVN-Revision: 47619
* remove references to non-existing kmod-usb3-mt7621
* ZTB WG2626 doesn't have an RTC (thanks to Piotr Dymacz!)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 47407
The PBR-M1 and other upcoming MT7621 boards have RTC chips on them. The
PBR-M1 also selects the kmod-rtc-pcf8563 by default. But the module itself
will not be build because CONFIG_RTC_CLASS is currently not enabled for its
kernel.
Enabling this option should fix the problem of the missing rtc device on
these boards.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46857
This patch:
* fixes wrong indentation
* fixes wrong names and descriptions (ex. Dlink -> D-Link)
* changes filenames to manufacturer names
* moves oem/unknown manufacturers boards to misc.mk profiles
* combines profiles for boards from the same manufacturers in one file (ex. Olimex)
* fix profile files structure (keep the same convention as in other targets, ex. ar71xx)
in various .mk profiles, in ramips target.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46631
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs
Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)
More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46454
This patch adds support for the Linksys RE6500 Range Extender
http://wiki.openwrt.org/toh/linksys/re6500
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46043
This patch is for PandoraBox PBR-M1 which is based on mt7621,
all the features work fine, including rtc, leds, button, usb3.0, etc.
Signed-off-by: tymon <banglang.huang@foxmail.com>
SVN-Revision: 46041
