Commit graph

2041 commits

Author SHA1 Message Date
Andrew Yong
3f31029b19 ramips: add support for VoCore2
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.

Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
            boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
  - USB 2.0 socket
  - MicroSD socket
  - 100Mbps Ethernet x1
  - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
    DAC/ADC (support WIP)
  - Micro USB for power and console (UART2)

Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
  SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
  original firmware uses Ralink SDK Wi-Fi drivers and not
  mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
  Ethernet or the micro USB console to configure Wi-Fi again

Signed-off-by: Andrew Yong <me@ndoo.sg>
2017-01-13 08:32:35 +01:00
Daniel Golle
287283e6e3 ramips: rt3883: fix typo in pinctrl lna_g_func
Spotted by forum users
https://forum.openwrt.org/viewtopic.php?pid=347439#p347439

Reported-by: Tom Psyborg <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-01-13 05:44:06 +01:00
Antonis Kanouras
f2b6412c72 ramips: Fix VLAN limits for MT7621 GSW
Without this patch swconfig will only allow setting up a total of 16
VLANs, with VLAN ID range of 0-15.

Tested on ubnt-erx.

Signed-off-by: Antonis Kanouras <antonis@metadosis.eu>
2017-01-10 08:18:15 +01:00
Felix Fietkau
018d80007e kernel: remove ubifs xz decompression support
It has been unused, and less useful than squashfs for cases where flash
space usage matters.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-09 14:07:06 +01:00
Hauke Mehrtens
88ca6390ea kernel: bump to 4.4.40
Refresh patches on all 4.4 supported platforms.
Compile & run tested: lantiq/xrx200

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-01-06 19:38:55 +01:00
Felix Fietkau
84bd74057f build: use mkhash to replace various quirky md5sum/openssl calls
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-05 11:09:12 +01:00
Victor Shyba
d6c831e0e5 generic: mtd: backport SPI_NOR_HAS_LOCK
This flag was added to 4.9 with upstream commit
76a4707de5e18dc32d9cb4e990686140c5664a15.

Signed-off-by: Victor Shyba <victor1984@riseup.net>
[refresh and adjust platform patches, fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-03 19:58:00 +01:00
L. D. Pinney
b28e94d4bf ramips: MiWiFi Nano fixes
Use the the dt-bindings macros and add the reset button.

Set the correct polarity for the LEDs and drop the default state.
Remove all trigger for the LEDs. According to the manual the LEDs are
only used to show the operation state, where blue means normal
operation.

Use the MAC-Addresses stored in EEPROM for the ethernet and the
wireless interface.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use leds only for boot status indication, add proper commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-02 19:16:54 +01:00
Rafał Miłecki
939ef157da ramips: fix NixcoreX1 profiles
There was a typo in Makefile that prevented using these profiles.

Fixes: a75ce960ac ("ramips: use different board names for variants")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-12-28 23:05:24 +01:00
Mathias Kresin
0cf581ca3a ramips: use new image build code for more devices
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
a75ce960ac ramips: use different board names for variants
Use different names for flash size related board variants, to make sure
that only images for the actual flash size are considered as valid by
the image validation code.

Remove the flash size suffix from the string returned by
ramips_board_detect() to ensure that existing scripts relying on the
former used boardname are still working.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
29f5e643ad ramips: sort rt305x image file alphabetical
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
d2b1148e75 ramips: use D-Link DIR-600 B1 image for B2 version
Everything set for the B1 is identical to the values uses for the B2
version.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
d2b6bf1416 ramips: fix image validation errors
The name from the Device define will be used in the metadata. Due to
typos/different spelling, this name might not match the one exported in
/lib/ramips.sh.

Fix all name mismatches which were found by checking if the name used
in the metadata exists in /lib/ramips.sh.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
ae3ac76e56 ramips: use destinct 11AC NAS board name
Use a distinct board name even if the board is near to identical to
the WeVO W2914NS v2.

To make sure that a 11AC NAS image can not be installed on a
WeVO W2914NS v2, both board need to use different names.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Henryk Heisig
4f033b2da6 ramips: fix tplink image building fix sysupgrade firmware on MR200
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-24 06:52:12 +01:00
Henryk Heisig
3a6353d910 ramips: enablemodem: move /lib/ramips.sh to start()
Fix build error: /etc/init.d/enablemodem: line 2: /lib/ramips.sh: No such file or directory

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-24 06:51:59 +01:00
Henryk Heisig
c8043137bb ramips: Add support to TP-Link Archer MR200
CPU: MT7620N 580MHz
Flash: 8MB
RAM: 64MB
build-in modem 3G/4G
four ethernet port 10/100Mbps

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-22 15:03:30 +01:00
Vitaly Chekryzhev
190ee7d86b ramips: add support for ZyXEL Keenetic Omni / Omni II
Factory image can be installed via Zyxel WebUI.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2016-12-22 15:03:13 +01:00
Giuseppe Lippolis
96a7ee3c80 ramips: adding registration for si3210
The si3210 is a SLIC device providing a complete analog telephone
interface and therefore frequently used in soho router.
The si3210 have a native spi interface to be controlled by the CPU
but currently there is no dedicated driver in lede.
Adding a registration for this device in spidev allow to control the
device in user space.
This way of patching is also in line with the rationale of the spidev
driver, see: http://marc.info/?t=148145791900001&r=1&w=2
The si3210 has been also added in the DWR-512 DT to properly describe
the HW.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2016-12-20 09:35:37 +01:00
Kevin Darbyshire-Bryant
79abb8f140 kernel: bump to 4.4.39
Bump & refresh patches for all 4.4 targets.

Compile & run tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2016-12-20 09:35:36 +01:00
L. D. Pinney
02ca833f04 ramips: WNDR3700v5 fix mtd partitions and radios
Fix the mtd partition layout and enable both radios in the dts

Tested-by Andrius Štikonas <andrius@stikonas.eu>
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
2016-12-20 09:35:35 +01:00
Giuseppe Lippolis
132b88ea39 ramips: adding DWM-158 3g Modem
This patch add the 3G modem DWM-158 to the usb-serial option driver.
The DWM-158 is a pcie 3G modem. It is embedded in the DWR-512 modem
supportet by lede. The patch has been submitted and merged in the upstream
linux-next repository.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2016-12-14 10:37:01 +01:00
BangLang Huang
960c477432 ramips: Fix led init script for Lenovo Y1/Y1s
This commit fix the led init script for Lenovo Y1 and
Y1S due to the manual and dts file.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-12-04 15:51:18 +01:00
Felix Fietkau
566de813c3 ramips: prevent packet forwarding on mt7620 between switch ports during init (FS#103)
By default, forwarding between all ports is allowed on init. This is
problematic in cases where some ports are supposed to be isolated from
each other, most commonly LAN/WAN separation.

REG_ESW_PORT_PCR(port) has a destination mask for a particular port,
controlling what other ports it is allowed to send packets to.
Instead of initializing all to 0xff (all ports), allow each physical
port to send to the CPU port, and the CPU port to send to all other
ports.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-04 11:41:49 +01:00
Yong-hyu, Ban
377eac0ceb ramips: fix LAN port order of WeVO W2914NS v2
Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
2016-12-04 08:22:07 +01:00
BangLang Huang
23b58f8acb ramips: fix PBR-D1 button definition
Due to the product specification, the button on PBR-D1 should be
reset, not wps.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-12-04 07:03:17 +01:00
Tobias Wolf
2e020e2cef ramips: add support for PCI based OHCI/EHCI support for F5D8235 V1
This router uses an PCI attached NEC EHCI controller to support the single USB port.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2016-12-04 07:03:17 +01:00
Tobias Wolf
13c0d208b2 ramips: introduce CONFIG_PCI and CONFIG_OF_*PCI for rt288x
This is a prerequisite for F5D8235 V1 to use PCI based OHCI/EHCI.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2016-12-04 07:03:17 +01:00
Tobias Wolf
c2ed721e89 ramips: improve F5D8235 V1 support
This fixes the partition name for the firmware splitter, the cfi
address and adds the mtd-eeprom address for wmac. It adds additional
LEDs and make use of them in diag.sh and 01_leds.

Please note that the ":blue:wired" LED is used because the
":blue:router" behaviour is unpredictable for failsafe indication. The
issue with the router LED is that you have two states only.
"off" is steady on and "on" blinks. Therefore the wired LED is more
suitable.

Furthermore it reuses the correct switch configuration definition to
reflect the device ports and numbering. Additionally fixes the issue
that the default configuration is not applied as no port 6 exists on
this device.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2016-12-04 07:03:17 +01:00
John Crispin
7c809f1687 ramips: fix sdhci support on mt7621
the IRQ level was wrong. refresh the patch while at it.

Signed-off-by: John Crispin <john@phrozen.org>
2016-12-01 18:30:41 +01:00
Andrew Yong
07b571a435 ramips: RB750Gr3: Add pwr LED and buzzer to DTS
use pwr LED in diag.sh
Expose unused pinmux pins as GPIOs
export power LED and buzzer pins
Use rb750gr3:blue:pwr LED in diag.sh for boot status instead of rb750gr3:green:usr

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-12-01 16:17:55 +01:00
Mathias Kresin
18c64f41c7 treewide: fix button keys codes used in dts
Use keycodes that matches the intended use case based on the label.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:34:23 +01:00
Mathias Kresin
4780e7e994 ramips: add size checks/append metadata where missing
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:34:23 +01:00
Mathias Kresin
6cc0ae27b9 ramips: fix Airlink AR670W factory image
Move the mkwrgimg build step to the makefile. It will be required by
other boards as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:34:23 +01:00
Yong-hyu, Ban
c723646f22 ramips: Add missing chunked-io directive to W2914NSV2.dtsi
Fix bug that LEDE failed to boot with this message:

WARNING: CPU: 2 PID: 1 at drivers/spi/spi-mt7621.c:214
mt7621_spi_transfer_one_message+0x28c/0x620()

Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
2016-11-26 22:39:21 +01:00
Andrew Yong
a7de18718d ramips: SamKnows SK-WB8 DTS cleanup
Use gpio.h definition of GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW. Remove unused backup partition to increase available JFFS space. As long as U-Boot env variable "bootcount" is < 3 (reset to 0 after boot by init script) SamKnow's U-Boot will not attempt to boot from the backup flash address (0xe30000).

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-26 22:35:52 +01:00
Mathias Kresin
ee6beb2e1c ramips: remove kmod-ledtrig-usbdev from recently added devices
None of the devices uses an usb led at all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-24 22:37:40 +01:00
Giuseppe Lippolis
ec1de9b1a6 ramips: Add device DLINK DWR-512-B
The Dlink DWR-512-B modem is a ralink 5350 processor based embedding
a 3G mini-pcie router.

The oem JBOOT bootloader has to be replaced by a RT5350 SDK
U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot
configured for the RT5350 256MiB SDR.

Main reason to change the bootloader is the encrypted header used to
store the kernel image. In this way an image can only be generated
using the propietary binboy tool (included in the GPL distribution
from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs
partition scheme. This is considered a big constraint (limited kernel
size and inefficient usage of flash space).

For interested people I pubblished the details of my investigation
about the encrypted firmware header here:
http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2016-11-23 08:36:11 +01:00
Mathias Kresin
8f561c6516 ramips: do not append metadata to CY-SWR1100 factory image
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-23 08:36:11 +01:00
Mathias Kresin
f1d0eba3ea ramips: cleanup dts files of mt7621 based boards
Fix a typo in mt7621.dtsi compatible string. Disable spi, sdhci and pci
in mt7621.dtsi and enable the nodes in the indiviual board dts files.
The nodes require further device specific configuration anyway.

Remove the m25p80@0 spi child node from mt7621.dtsi and add the
chunked-io parameter to the individual board dts files. Fix the spi
flash compatible string for the WNDR3700V5.

Drop the mt7621-eval-board compatible string for all boards which are
not the eval board.

Drop the linux,modalias parameter from spi flash node.

Remove the xhci node from board files, it is already enabled in dtsi.
Disable xhci for boards not having usb ports populated.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-23 08:36:10 +01:00
Mathias Kresin
18e7f49975 ramips: order mt7621.mk alphabetical
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-23 07:09:03 +01:00
Andrew Yong
fe43d90d93 ramips: fix wrong check for MT7621AT
fix in sdhci Use ralink_soc == MT762X_SOC_MT7621AT instead of CONFIG_SOC_MT7621 which is
wrong and breaks builds on mt7620a-similar platforms (MT7621, MT7688)

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-21 16:49:54 +01:00
Andrew Yong
605cab749e ramips: Fix sdhci kernel panics on MT7621
Enable work-arounds present in the code commented-out but needed to write to
sdcard on mt7621 which currently causes kernel to oops when engaging in
serious writing to sdcard. With this change applied, there are still
occasional warnings thrown by the mmc driver, however, at least it no longer
crashes the system and even large writes (full-card dump/erase/write/compare)
don't show any corruption.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

Rebase to LEDE and added "CONFIG_SOC_MT7621" check to ensure non-MT7621 devices do not face performance regressions.
Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-21 12:31:39 +01:00
perillamint
68634426fe ramips: add support for WeVO W2914NS v2
Signed-off-by: Yong-hyu Ban <perillamint@gentoo.moe>
2016-11-21 10:13:17 +01:00
Felix Fietkau
478f1f6b16 ramips: append metadata to images
metadata checks are not enforced yet, because some images are still
being built by legacy code

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-19 11:24:10 +01:00
Vitaly Chekryzhev
348344874c ramips: add support for ZyXEL Keenetic Viva
Factory image can be installed via Zyxel WebUI.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-18 08:54:57 +01:00
Vitaly Chekryzhev
5f38d1ad85 ramips: add MT7620 MIB support for switch and port
Move definitions to header. Replace array size definitions with macro.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[merged into 0513-net-mediatek-add-swconfig-driver-for-gsw_mt762x.patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
2016-11-17 20:01:21 +01:00
Jasper Scholte
3d680c5728 ramips: add support for Sitecom WLR-6000
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.

The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.

The stock firmware uses the following mac addresses:

LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5:   00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)

Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:

2.4GHz: 00:0C:F6:AA:BB:D8
LAN:    00:0C:F6:AA:BB:D9
WAN:    00:0C:F6:AA:BB:DA
5 GHz:  00:0C:F6:AA:BB:DC

The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.

There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.

Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.

Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-17 06:39:52 +01:00
Dominik Menke
8b65fef173 ramips: add support for Digineo AC1200 Pro
This is basically a ZBT-WG3526 (mt7621 SoC), but with 32M flash.

Signed-off-by: Dominik Menke <dom@digineo.de>
2016-11-17 06:39:52 +01:00
Dominik Menke
6e3d7897f7 ramips: cleanup ZBT-WG3526.dtsi
- replace magic numbers with GPIO_* constants
- replace generic PCI definitions with correct vendor and
  device identification

Signed-off-by: Dominik Menke <dom@digineo.de>
2016-11-17 06:39:52 +01:00
Dominik Menke
efbb654f6c ramips: split ZBT-WG3526.dts into dtsi and dts files
Signed-off-by: Dominik Menke <dom@digineo.de>
2016-11-17 06:39:52 +01:00
Martin Weinelt
5247ac2f80
ar71xx, ramips: reduce CPU load and flickering on devices using rsslieds
Polling every 40ms causes more than 10% CPU load on weak devices. An
interval of 200ms is much more reasonable.

Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net>
[Matthias Schiffer: adapt OpenWrt patch; add ramips; extend commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-16 01:42:15 +01:00
Felix Fietkau
728ab77d3d ramips: fix polling switch interrupts
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-14 20:06:15 +01:00
Felix Fietkau
3d0e965c8b ramips: add port index in switch config for buffalo WHR-* and WSR-* devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-14 20:04:36 +01:00
Felix Fietkau
4cdbc90a37 ramips: add hack to detect missing mt7621 cpu cores
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-14 19:59:32 +01:00
Felix Fietkau
a17872ec4f ramips: fix status LED for WHR-300HP2
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-14 17:55:27 +01:00
Mathias Kresin
2b55c83e68 treewide: dts: use keycode defines from input dt-binding
All compiled device tree files not mentioned are binary identical to the
former ones.

Fix the obvious decimal/hex confusion for the power key of ramips/M2M.dts.

Due to the include of the input binding header, the BTN_* node names in:

  - ramips/GL-MT300A.dts
  - ramips/GL-MT300N.dts
  - ramips/GL-MT750.dts
  - ramips/Timecloud.dts

will be changed by the compiler to the numerical equivalent.

Move the binding include of lantiq boards to the file where they are
used the first time to hint the user where the values do come from.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-13 07:07:58 +01:00
Mathias Kresin
77b807999d treewide: dts: use C style includes
No functional change but allows me to use one script to compile all
device tree source files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-12 21:04:15 +01:00
Mathias Kresin
de40d45363 treewide: dts: fix dtc compiler warnings
Fixes invalid device tree parameters.

Drop the mvsw61xx node used in mvebu device tree source files. It looks
like some kind of ethernet switch cargo cult. Neither the
marvell,88e6352 nor the marvell,88e6172 compatible strings can be found
in any LEDE file or in the kernel sources.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-12 21:04:15 +01:00
Mathias Kresin
cc5c8f681e ramips: add TEW-691GR/TEW-692GR 2.4 GHz interface mac addresses
Assign an unused MAC addresses to the 2.4GHz wifi interface as it was
originally planed but not possible.

The MAC address numbering of the TEW-691GR changes to the following
pattern:

  LAN:  AA:BB:CC:DD:EE:0C
  WIFI: AA:BB:CC:DD:EE:0D
  WAN:  AA:BB:CC:DD:EE:0F

The MAC address numbering of the TEW-692GR changes to the following
pattern:

  LAN:    AA:BB:CC:DD:EE:e4
  WAN:    AA:BB:CC:DD:EE:e5
  2.4GHz: AA:BB:CC:DD:EE:e7
  5 GHz:  AA:BB:CC:DD:EE:e8

Set the label and compatible string for the TEW-692GR PCIe wireless
according to the the PCI binding documentation.

Use the wifi@0,0 label and the pci0,0 compatible string since the PCI
vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-09 20:23:00 +01:00
Mathias Kresin
d8dd207ea6 ramips: use the ralink,mtd-eeprom device tree property
Use the ralink,mtd-eeprom instead of invoking the userspace firmware
loader.

Set the label and compatible string according to the the PCI binding
documentation.

Use the wifi@0,0 label and the pci0,0 compatible string in case the
PCI vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).

This commit might fixes the PCIe wireless for the Buffalo WHR-600D.
This board was mentioned in the board 10-rt2x00-eeprom firmware hotplug
script but never had the correct eeprom name set to trigger the
firmware from flash extraction.

Use the usual eeprom for the soc wmac of the Dovado Tiny AC.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-09 20:22:59 +01:00
Roger Pueyo Centelles
5f6e948551 ramips: Add support for Wavlink WL-WN575A3
This commit adds support for the Wavlink WL-WN575A3, a dual-band wall-plug
wireless router with the following specifications:

 - CPU: MediaTek MT7628AN 580MHz
 - Flash: 8MB
 - RAM: 64MB
 - Ethernet: 2x 10/100 Mbps (switched)
 - 2.4 GHz: 802.11b/g/n SoC, MIMO 2x2, 20 dBm
 - 5 GHz: 802.11a/n/ac MT7612E, MIMO 2x2, 20 dBm
 - Antennas: 4x external (2 per radio), non-detachable
 - LEDs: 4 programmable + LAN, WAN, POWER
 - Buttons: reset, WPS

Flashing instructions:

Factory U-boot launches a TFTP client if WPS button is pressed during power-on.
Rename the sysupgrade file and configure a TFTP as follows:

 - Client (WL-WN575A3) IP: 192.168.10.101
 - Server IP: 192.168.10.100
 - Filename: firmware.bin

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2016-11-08 11:17:10 +01:00
BangLang Huang
bc4109845d ramips: fix Newifi D1 profile
the images were generated for the wrong flash size.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-11-08 11:17:10 +01:00
Sven Schwermer
5511c1c7c1 ramips: Use MT7621 I2C driver for MT7628/MT7688
The i2c-ramips driver does not work for the MT7628/MT7688 SoCs, the
i2c-mt7621 driver does.

Signed-off-by: Sven Schwermer <sven.schwermer@arcor.de>
2016-11-03 08:27:20 +01:00
Andrew Yong
faf94d926e ramips: add support for MikroTik hEX v3 (RB750Gr3)
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).

RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.

Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.

The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.

A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-02 10:25:44 +01:00
Stijn Segers
2f2ea7b44c kernel: update kernel 4.4 to version 4.4.30
This patch bumps the 4.4 kernel from .28 to .30 and refreshes the patches.
Compile-tested on ar71xx, x86/64, ramips/mt7621, brcm47xx and kirkwood.

Run-tested on ar71xx & ramips/mt7621, brcm47xx and kirkwood (last two confirmed
by P. Wassi).

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-11-02 10:25:44 +01:00
Stijn Segers
eefe07ef4d ramips: add usb packages into DIR-860L B1 profile
This patch adds the kmod-usb3 and kmod-usb-ledtrig-usbport packages to the
DIR-860L B1 profile. The DIR-860L B1 has a USB 3 port.

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-11-02 10:25:44 +01:00
Henryk Heisig
a34f96d6cf ramips: Archer C50 cleanup
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>

Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-31 16:58:41 +01:00
Rosen Penev
369884c2a1 ramips: Add RTC driver to kernel for working hctosys
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2016-10-31 16:41:26 +01:00
Xuefu Lin
8312738806 ramips: fix PSG1218 LEDs
Signed-off-by: Xuefu Lin  <xuefulin@gmail.com>
2016-10-26 12:37:45 +02:00
Rafał Miłecki
0658527e1e switch to the new usbport LED trigger
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:09:45 +02:00
YuheiOKAWA
4050cfebda ramips: add support for Planex VR500.
SOC:	MT7621A
RAM:	256MiB
NOR:	MX25L51245G

Non Wireless Router.

Issue: soft reboot problem. SPI Flash do not exit 4byte address mode.

Signed-off-by: Yuhei Okawa <tochiro.srchack@gmail.com>
2016-10-15 11:36:51 +02:00
Mathias Kresin
bcfbeae79f ramips: use rfkill for wps button on wlan only boards
All of the touched boards don't have an ethernet port. Allow to use the
wps button on these boards to enable the wireless radio after boot.

The force enabled wireless for the DCH-M225 is removed. It is reckless
to bring up an unencrypted wireless network by default these days.

Using the wps button to bring up the radio seam to me the better
approach.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
0a219c8dfb ramips: use rootfs splitter and new image build code for BR-6475ND
Use the edimax uImage splitter instead of the fixed size rootfs
partition.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
e7ec5df33b ramips: move edimax images to the new build code
Images installed via TFTP recovery or the Edimax webinterface of the
3g-6200n(l) are writting with the edimax header to flash.

Use only one image type for these boards. The migration to the
factory only images need to be done via TFTP recovery.

Use the same start address for the 3g-6200n(l) factory images as the
stock firmware images.

Thanks to Jan Dostrasil for reporting all the issues of the 3g-6200nl
and the patient testing of all changes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
6391af2f1f ramips: improve edimax 6200n/nl support
Assign the reset functionality to the wps/reset buttons. Use the wlan
switch of the 6200n to enable/disable wlan.

Add the internet led of the 6200nl and use the led for boot status
indication

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
51bca43f39 ramips: fix edimax 6200nl switch config
With 3a9752bbd2 and later changes to
ramips_set_preinit_iface() the default vlan config applied during
preinit was changed. These changes were made without updating the
default network config to ensure that vlan interfaces used for lan/wan
are still configured.

Fix the issue by using the default all LAN portmap and disabling not
connected switch ports using portdisable device tree parameter.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
bbdf2ac305 ramips: tag the CPU switch port
With de51026515 the explicit tagging of
the CPU port was removed. This leads to a not working default network
config, with vlans enabled but disabled CPU tagging, for boards where
all switch ports are having the same role.

In case the ports are having different roles set, tagging is is set
implicit for the CPU port by ucidef_add_switch().

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
b35dd9584e ramips: remove fixed lan/wan interface for switch configs
Don't set the lan/wan interface when using ucidef_add_switch. This
results into a wan interface albeit all ports a annotated as lan ports.

ucidef_add_switch takes care of setting the correct lan/wan interface
according to the annotation of the ports.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Klaus
df5416296c ramips: add support for Zyxel NBG-419N2 (WAP3205v2)
applied bb-final-ramips-add-zyxel-nbg-419n2.patch from
123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65;
see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905,
modified slightly to fit to CC release and to new lede build
system: image/rt305x.mk include file is used now
changed NBG-419N2.dts format to fit style of other dts files

Signed-off-by: Klaus <k-laus@quantentunnel.de>
2016-10-04 11:50:51 +02:00
Xuefu Lin
dce5c4f5c8 ramips: Add support for Phicomm K2 PSG1218
- CPU: MT7620A 580MHz
- Flash: 8MB - RAM: 64MB
- External PA+LNA on both WLAN2.4 and WLAN5
- 4x LAN ethernet and 1x WAN ethernet

Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
2016-10-04 11:50:46 +02:00
Álvaro Fernández Rojas
7d559169c5 kernel: update to v4.4.23
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-30 20:08:21 +02:00
Stijn Segers
949cfbb243 kernel: update kernel 4.4 to version 4.4.22
Forgot to update kernel-version.mk, so updated patch. Compile-tested on x86/64 and ar71xx; run-tested on x86/64 and ar71xx.

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-09-30 13:34:04 +02:00
Cezary Jackiewicz
e79e555c0e ramips: Xiaomi MiWiFi Nano: fix status led
- add status led for Xiaomi MiWiFi Nano
- revert af1e70b4a7 , this should not be added.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-09-29 11:39:41 +02:00
BangLang Huang
142ec7ada9 ramips : add support for Newifi D1
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-09-27 17:50:22 +02:00
BangLang Huang
9fe833e1d0 ramips : add support for PandoraBox D1
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-09-27 17:50:22 +02:00
Cezary Jackiewicz
66aae9a271 ramips: Add support for ZBT-CPE102
- CPU: MT7620N 580MHz
- Flash: 8MB
- RAM: 64MB
- build-in minipcie slot for modem 3G/4G
- one ethernet port 10/100Mbps

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-09-27 17:50:21 +02:00
Matthias Schiffer
43bf3e80b2
ramips: fix DEVICE_PACKAGES of Ubiquiti EdgeRouter X
kmod-rt2x00-lib and kmod-mac80211 need to be removed, as they depend on
kmod-cfg80211. kmod-rt2800-pci should not be installed anyways.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-26 17:57:57 +02:00
Matthias Schiffer
175fbe4d4e
ramips: move /lib/ramips.sh include in /etc/init.d/bootcount into start()
Enabling the init script offline will print an error otherwise.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-25 23:26:42 +02:00
Martin Blumenstingl
d72e838429 ramips: do not "local" variables outside of a function
Older busybox versions allowed using the local keyword outside of
functions, whereas 1.25.0 (which was introduced in 06fa1c46fc) do not
allow this anymore (leading to the following error when executing the
script: "file: local: line nn: not in a function").

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2016-09-24 01:17:18 +02:00
Álvaro Fernández Rojas
41eab9048b kernel: update kernel 4.4 to version 4.4.21
Refresh patches for all targets that support kernel 4.4.
Compile-tested on brcm2708 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-16 10:17:27 +02:00
Mathias Kresin
eb88a9cacb ramips: fix wrong blocksizes
The D-Link DIR-860L B1 has a flash chip which doesn't support
4K sectors. Since the DIR-860L B1 was the only mt7621 board which had
the 4k blocksize set, the 4K sector support is removed from the kernel
config.

I've checked the flash chips of all boards having set a 4K blocksize
again. This time I searched harder to finding bootlogs instead of
relying on wikis articles and/or the device tree source file.

The Planex MZK-DP150N has an en25q32b instead of the mentioned one in
the dts. Albeit the en25q32b supports 4K sectors, 4K support is not
enabled in the driver. Change the blocksize for this board back to 64K.

Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-15 09:53:37 +02:00
Álvaro Fernández Rojas
d14c28fc80 kernel: update kernel 4.4 to version 4.4.20
Refresh patches for all targets that support kernel 4.4.
Compile-tested on brcm2708 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-15 08:10:55 +02:00
Mathias Kresin
925e63e71f ramips: enable 4K sector support in kernel config
This is a follow up to 28110727f1
"ramips: set blocksize for 4MB devices". I've missed to include the
required changes of the kernel configs to enable 4K sector size
support.

The option is only enabled for targets having boards with 4k sector
size flash chips.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-13 22:06:08 +02:00
Mathias Kresin
1cd0a4c688 image: add KERNEL_SIZE to the default device vars
This reverts commit ec37a56587 and fixes
the underlying issue.
2016-09-13 19:36:41 +02:00
Felix Fietkau
d27bce8d28 build: drop UBI EOF marker from images by default
Only add them where they are actually required.
Should help with compatibility issues with stock U-Boot images that
access UBI

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-12 18:21:52 +02:00
Mathias Kresin
c1578d4fc9 cleanup ucidef_set_interface* usage
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:32:25 +02:00
Mathias Kresin
0f6d0afa13 ramips: board.d merge redundant switch/interface configs
Fix alphabetical order distortions as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:28:38 +02:00
Mathias Kresin
7d9ef9080c ramips: set blocksize for remaining rt3883 devices
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-08 21:03:57 +02:00
Mathias Kresin
9f531efc59 ramips: remove old build code seama recipe
Now that all seama images are using the new build code this seama recipe
used with the old build code can be dropped.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 15:27:46 +02:00
Mathias Kresin
fb39b77ccb ramips: switch DIR-610 A1 to new image build code
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-08 22:21:23 +02:00
Mathias Kresin
bd39104e95 ramips: switch some rt3883 devices to new build code
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 10:18:31 +02:00
Mathias Kresin
0f3600ccee ramips: move seama build recipe to Makefile
The identical build step is defined twice. Move it to the parent
Makefile to use only one version.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 09:43:31 +02:00
Mathias Kresin
74da44cfc2 ramips: switch DIR-615 H1 to new image build code
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-02 07:34:36 +02:00
Mathias Kresin
483fd5f6ad ramips: add build recipe for senao header
Add it to the Makefile to allow a board which will be supported soon
to use the recipe as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-17 07:49:34 +02:00
Mathias Kresin
28110727f1 ramips: set blocksize for 4MB devices
Set the blocksize for devices having only 4MB of flash for ramips
devices already using the new image build code.

Informations about the used flash chip are gathered from the OpenWrt
wiki, wikidevi, forums, OEM bootlogs or the compatible property in the
device tree source file.

The en25q32b from the AirLive Air3GII does not have 4k support in the
kernel.

For the following boards no information about the used flash chip could
be found and a 64k blocksize is assumed:

  - Ralink V11ST-FE
  - Ralink AP-RT3052-V22RW-2X2
  - MediaTek MT7628 EVB
  - MediaTek MT7621 EVB
  - UPVEL UR-326N4G
  - Buffalo WZR-AGL300NH

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 09:56:35 +02:00
Mathias Kresin
05ab2323ff ramips: don't set the same max image size twice
The ralink_default_fw_size_8M is already set for the default device.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-04 10:04:20 +02:00
Mathias Kresin
a499d0a6b5 image: specify max image size in Kilobyte/Megabyte
Use the k and m unit suffix to be consistent with the blocksize.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-04 09:58:02 +02:00
Mathias Kresin
e7ec7a08aa image: use k as unit suffix for blocksize
Use k as unit suffix for kilobyte to have a the same unit regardless of
the used filesystem.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-04 08:56:05 +02:00
Mathias Kresin
85fefcdb61 kernel: mtd: backport Macronix sector size fix
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 09:27:09 +02:00
Mathias Kresin
5369a03d52 ramips: use lower case names for TEW-69xGR images
Use lower case variant of the device name for to images to be
consistent with all other images names.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-09 07:12:37 +02:00
Mathias Kresin
775f93e898 ramips: fix wrong TARGET_DEVICES
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-08 23:51:46 +02:00
Mathias Kresin
034c5cb820 ramips: fix wrong device title
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-08 07:32:00 +02:00
Daniel Golle
083ef3fefe ramips: add support for Mercury MAC1200R v2
MT7628AN + MT7612E, 8MB SPI flash, 64MB DDR RAM
reset button GPIO is still missing (anyone?)
bootloader password is 'slp'

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2016-09-09 02:38:06 +02:00
Felix Fietkau
aa53f78038 build: fix subtarget descriptions
Move Target/Description above the target.mk include

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-04 13:35:11 +02:00
Felix Fietkau
358cd6d9eb ramips: fix legacy initramfs images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-03 10:47:42 +02:00
Jonas Gorski
b962da4d92 ramips: mt7621: switch to 24kc
1004kc is just a SMP capable 34kc, and GCC treats 24kc and 34kc exactly
the same and will generate identical code, so there is no need to tune
to 1004kc instead of 24kc.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2016-08-23 11:55:32 +02:00
Stijn Tintel
8072264b96 kernel: update kernel 4.4 to version 4.4.19
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon and x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-08-23 10:51:17 +03:00
Mathias Kresin
c9e6b173f7 ramips: fix build of TRENDnet TEW-69xGR images
The image generation for TEW-691GR and TEW-692GR was broken since
79d02229 due to the move of the UMedia recipe to another Makefile.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-20 11:47:25 +02:00
Mathias Kresin
c892f37b30 ramips: move umedia build step to Makefile
Some rt3883 based boards need this one as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-20 11:47:25 +02:00
Mathias Kresin
bcd2113a32 ramips: TEW-691GR: fix switch and wireless
Due to the missing phy-mode setting, the switch wasn't initialised.

The wireless requires an eeprom to work. Use the same mac addresses as
the stock firmware.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-20 11:47:25 +02:00
Mathias Kresin
a7c6cf5182 ramips: TEW-692GR: fix switch and wireless
The AR8327 initvals were not copied to the DTS during the switch from
mach file to device tree and broke the switch on the device.

The former used PORT6 related initvals were wrong and have been
corrected.

The phy mode setting for the switch was missing in the DTS as well.

The wireless requires an eeprom to work. The dual band wireless chips
have both bands enabled by default but only one band per chip is
working.

The stock firmware uses the following mac addresses:

LAN:    AA:BB:CC:DD:EE:E4
WAN:    AA:BB:CC:DD:EE:E4
2.4GHz: AA:BB:CC:DD:EE:E4
5 GHz:  AA:BB:CC:DD:EE:E8

Assuming the mac address range :E4 to :E8 is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:

LAN:    AA:BB:CC:DD:EE:E4
2.4GHz: AA:BB:CC:DD:EE:E4
WAN:    AA:BB:CC:DD:EE:E5
5 GHz:  AA:BB:CC:DD:EE:E8

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-20 11:45:45 +02:00
Mathias Kresin
05912a304c ramips: rt3883: fix dtc compiler warning
Fixes the following compiler warning:

Warning (reg_format): "reg" property in /ethernet@10100000/port@0 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /ethernet@10100000/port@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /ethernet@10100000/port@0

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-20 11:42:42 +02:00
John Crispin
99a1888287 swconfig: revert the portmapping patches, they seem to cause a segfault
Revert "kernel/swconfig: remove obsolete portmapping feature from swconfig"

This reverts commit 675407baa4.

Revert "swconfig: remove obsolete portmapping feature"

This reverts commit fca1eb349e.

Signed-off-by: John Crispin <john@phrozen.org>
2016-08-16 10:20:01 +02:00
John Crispin
675407baa4 kernel/swconfig: remove obsolete portmapping feature from swconfig
Signed-off-by: John Crispin <john@phrozen.org>
2016-08-15 15:18:35 +02:00
Felix Fietkau
592c0a1cd2 ramips: fix legacy image build
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-08-11 17:07:37 +02:00
Chuanhong Guo
0f73801f4f ramips: Add support for Thunder Timecloud
Thunder Timecloud is a small NAS with MT7621A. It has 1 USB port and an
SD Card slot. There is no wireless cards.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2016-08-10 03:04:08 +02:00
Jimmy Zhong
2b1f4945b1 ramips: Add support for TEW-714TRU
Signed-off-by: Jimmy Zhong <mb300sd@mb300sd.net>
2016-08-10 03:03:50 +02:00
Jonas Gorski
bebcb81da5 ramips: switch from 24kec to 24kc
Since the only difference between 24Kec and 24Kc is the addition of DSP
ASE support, and we don't use it anymore, there is no need to keep 24Kec
as a separate cpu type.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2016-08-08 11:29:56 +02:00
John Crispin
281483e097 ramips: enable nand support for mt7621
this makes sysupgrade work on the ERX

Signed-off-by: John Crispin <john@phrozen.org>
2016-08-03 15:30:13 +02:00
John Crispin
8e75630d1d ramips: updated remaining profiles to the new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-08-03 15:30:13 +02:00
Felix Fietkau
9abbaa9539 build: remove MIPS dsp/dsp2 CPU_SUBTYPE
There does not seem to be any meaningful difference in generated code.
This will save some time and space on snapshot builds

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-08-03 14:56:45 +02:00
P.Wassi
686617ae39 ramips: Rename TP-Link Archer C50 LEDs
Rename LEDs in TP-Link Archer C50 from [manufacturer name]
to [board name] ("tp-link" -> "c50")

Signed-off-by: P.Wassi <p.wassi@gmx.at>
2016-07-26 08:39:36 +02:00
P.Wassi
dbf107cd2b ramips: Improve TP-Link Archer C20i support
Improve / finalise TP-Link Archer C20i support.

Signed-off-by: P.Wassi <p.wassi@gmx.at>
2016-07-26 08:39:36 +02:00
Felix Fietkau
63b525dd6b image: add a helper variable for getting kernel/rootfs from within image Build/* templates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-31 12:25:25 +02:00
Jo-Philipp Wich
db49dd894e build: rename sysupgrade-nand to sysupgrade-tar
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-07-29 16:53:03 +02:00
P.Wassi
525b9edc8a ramips: unify etc/board.d/01_leds configuration
Introduce an optional parameter at the local set_usb_led and
set_wifi_led function such that they can take a triggering
device. If no parameter is passed, behaviour is unchanged.
Signed-off-by: P.Wassi <p.wassi@gmx.at>
2016-07-24 06:38:30 +02:00
Michael Lee
0d5277f73f ramips: dch-m225 don't have ethernet. default enable wifi
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-24 06:38:30 +02:00
Paul Wassi
104114fe00 ramips: remove indentation in etc/board.d/01_leds
Remove indentation at end of line in base-files/etc/board.d/01_leds
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-07-24 06:38:29 +02:00
John Crispin
6674006bd0 ramips: add missing i2s alias
Signed-off-by: John Crispin <john@phrozen.org>
2016-07-24 06:38:29 +02:00
Jo-Philipp Wich
b051ac76e8 ramips: mt7621: add missing kernel symbol
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-07-16 13:59:12 +02:00
Hauke Mehrtens
efa1960abb kernel: update kernel 4.4 to version 4.4.15
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-07-13 15:39:15 +02:00
Michael Lee
9062c4fe99 ramips: modify audio kernel module and add dma options
* add gdma and hsdma kernel modules
* i2s support all ramips targets except rt288x
* i2s need gdma to transfer data
* add simple audio kernel module. it support device tree binding

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
Michael Lee
c3e420f28c ramips: Add support for D-Link DCH-M225
D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash,
3.5mm audio out support. but no ethernet and usb ports.
so you must default enable wifi.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
Michael Lee
36d98e6c7a ramips: add MT7620 pinmux bits for mdio as refclk
The MT7620 uses a 2 bit wide configuration of the mdio.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
Michael Lee
0460e9ffca ramips: enable MTD_SPLIT_SEAMA_FW for mt7620
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
L. D. Pinney
cf8c77be6b ramips: Add support for the NixCore X1 Module
The NixCore X1 is a Ralink/MediaTek rt5350 WiFi Module.

http://nixcores.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Drew Gaylo <drew@nixcores.com>
2016-07-11 14:19:47 +02:00
Rene Treffer
8876575601 ramips: fix partition size for RT5350F-OLINUXINO
The partition size is wrong, leading to out-of-disk-space even on no/moderate use.

Upstream fix from vendor: 2f25eb57ed
Suggested fix for openwrt: https://dev.openwrt.org/ticket/20321

Signed-off-by: Rene Treffer <treffer@measite.de>
2016-07-11 14:19:47 +02:00
John Crispin
252f751611 ramips: fix usb phy initialisation
this broke usb20 device detection.

Signed-off-by: John Crispin <john@phrozen.org>
2016-07-11 14:19:46 +02:00
Felix Fietkau
201dbb9fe8 ramips: fix build error in ubnt-erx initramfs factory image
Build initramfs kernel image, but skip factory image if initramfs size
is too big.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-06 10:12:37 +02:00
John Crispin
eca1021e5c ramips: fix buffalo wmr-300 lan port
Signed-off-by: John Crispin <john@phrozen.org>
2016-07-05 22:59:14 +02:00
John Crispin
2c9073282d ramips: fix MT7621 gsw handling
based on https://forum.openwrt.org/viewtopic.php?pid=323671#p323671

Signed-off-by: John Crispin <john@phrozen.org>
2016-07-05 22:59:13 +02:00
John Crispin
69a626b441 ramips: fix mt7621 SoC detection
Signed-off-by: John Crispin <john@phrozen.org>
2016-07-05 22:59:13 +02:00
John Crispin
d09f0045ea ramips: fix up switch settings for Sitecom WL-351 v1 002
Pinmux for rgmii needs to be set to rgmii, not gpio.
Hide the ESW switch on boot (using new rgmii esw devicetree attribute).
Also add a Sitecom-specific profile, since the image needs to include
the rtl8366 kernel driver.

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
2016-07-03 08:00:26 +02:00
John Crispin
2dc9beddc0 ramips: disable the WP pin on the SDK mmc driver
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-30 22:48:39 +02:00
John Crispin
81add8f753 ramips: fix pinmux typo
Reported-by: Joy Kicer <joykicer@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-30 22:48:39 +02:00
Matthias Schiffer
0a0caa2656
ramips: set correct LAN/WAN MAC addresses on DIR-860L B1
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2016-06-30 17:12:38 +02:00
Matthias Schiffer
103ed00cfb
ramips: add button support and make LEDs known to userspace for DIR-860L B1
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2016-06-30 17:12:38 +02:00
Matthias Schiffer
fa9811814a
ramips: fix fixseama call on first boot
Commit "kernel: mtdsplit: calculate kernel partition precisely for Seama"
changed the kernel partition to only contain the kernel itself and not
the Seama header. Adjust the fixseama call to match what is used on
brcm53xx.

This fixes failing to boot a second time after flashing the factory image
on the affected devices.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2016-06-30 17:12:38 +02:00
Hauke Mehrtens
84d489f64f kernel: update to version 4.4.14
Changelog: https://cdn.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.4.14

Some manual changes to target/linux/generic/patches-4.4/610-
netfilter_match_bypass_default_checks.patch were needed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-26 18:20:37 +02:00
Roger Pueyo Centelles
5fba0f0c0c ramips: add suport for ZBT APE522II
The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has
64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with
802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac
MT7612E-based 5 GHz radio.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2016-06-22 19:32:06 +02:00
Michael Lee
81913e4996 ramips: remove duplicate i2c dts info
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-20 11:45:44 +02:00
Michael Lee
60ccfbbad0 ramips: update i2c drivers
* add rt_i2c structure to store driver data
* rewrite read/write check function and add i2c error status check.
  so we don't need to wait until time out.
* add 10 bits address support. according to the data sheet i think
  it is possible. but i haven't verify it.
* the most important is start transfer only need once. otherwise
  it cause I2C_STARTERR status.
* add set i2c clock speed register by dts options "clock-frequency".
  not just hard code it.
* add mt7621 i2c driver. i just copy i2c-ralink.c and change register
  names. and the hardware don't support error status. so i remove it.
  but the logic is the same.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-20 11:45:44 +02:00
John Crispin
b180f24a3b Revert "ramips: update i2c drivers"
This reverts commit d8202a8409.

the commit broke I2C on various boards.

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-17 04:13:07 +02:00
John Crispin
bfcbca3e04 mediatek/ralink: fix boardnames
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 13:00:30 +02:00
Jo-Philipp Wich
5550d98015 ramips: fix kmod-sound-mt7620 packaging
Commit 9ff8928bb9 renamed the snd-soc-mt7620-i2s
driver and dropped snd-soc-mt7620-wm8960 which selected CONFIG_SND_SOC_WM8960
breaking all ramips builds due to undefined kernel config symbols.

Rework the kmod-sound-mt7620 package to explicitely select the
CONFIG_SND_SOC_WM8960 symbols and change it to bundle the renamed .ko file.

Also remove the @BROKEN flag and exclude it on the rt288x subtarget instead.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-14 14:31:18 +02:00
Henryk Heisig
01fb393c67 ramips/image: Add Archer C50 to mt7620 Makefile
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-06-13 22:51:43 +02:00
Henryk Heisig
75af981239 ramips/base-files: Add support for Archer C50
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-06-13 22:51:43 +02:00
Henryk Heisig
1c00c09eb6 ramips/dts: Add support for Archer C50
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-06-13 22:51:43 +02:00
Michael Lee
9a4935687d ramips: add support for DuZun DM06
DuZun DM06 is a develop board based on mt7628
64M RAM, 8M SPI Flash, 1 WAN, 1 LAN.
wm8960 codec with line out, line in and speaker output.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:43 +02:00
Michael Lee
49b7421836 ramips: enable wm8960 kernel menuconfig select option
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:43 +02:00
Michael Lee
6f61990d15 ramips: add i2s clocks
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:43 +02:00
Michael Lee
921d782eb7 ramips: update i2s dtsi files
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee
9ff8928bb9 ramips: improve i2s drivers
* remove mt7620-wm8960.c use simple card and DTS to do it
* add old chips support
* add 12Mhz refclk setup. this is hard code. need use clock framework
  rewrite it
* add interrupt error status support for debug. default disable it.
  because it cause to many interrupts
* add setup bclk suport not hard code it
* add 24 bits support for mt7628. not verified
* use regmap api to control registers
* add txdma-req/rxdma-req DTS params for DMA use

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee
42bbe28cf1 ramips: add i2c clock
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee
011ce1fad6 ramips: update i2c dtsi files
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee
d8202a8409 ramips: update i2c drivers
* add rt_i2c structure to store driver data
* rewrite read/write check function and add i2c error status check.
  so we don't need to wait until time out.
* add 10 bits address support. according to the data sheet i think
  it is possible. but i haven't verify it.
* the most important is start transfer only need once. otherwise
  it cause I2C_STARTERR status.
* add set i2c clock speed register by dts options "clock-frequency".
  not just hard code it.
* add mt7621 i2c driver. i just copy i2c-ralink.c and change register
  names. and the hardware don't support error status. so i remove it.
  but the logic is the same.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee
f36d624d88 ramips: add gdma hsdma dts info
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee
f6fc591561 ramips: enhance dma engine support
* fix compiler error. device_control operation not support now.
* add old chips support 8 channels. new chips support 16 channels.
* add mt7621 hsdma driver. data sheet says it has two channels.
  but after test only one channel support.
* add memory to memory DMA support. i use dmatest kernel module to
  verify this function. on rt305x it will copy more data. on mt7621
  only two channels can works at the same time. these two chips
  maybe have hardware bugs. because on other chips don't have these bugs.
* use tasklet to handle remaining dma requests.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Álvaro Fernández Rojas
0aa6c7df60 kernel: update kernel 4.4 to version 4.4.13
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-12 15:51:54 +02:00
Felix Fietkau
7eeb254cc4 treewide: replace nbd@openwrt.org with nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-07 08:58:42 +02:00
Joseph C. Lehner
065de8bd7a ramips: fix Netgear EX2700 images
Calling `cat foo bar | dd ... conv=sync` *may* add
extraneous padding. Avoid this.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2016-06-05 23:23:57 +02:00
Joseph C. Lehner
8b0fbd8e70 ramips: rebrand Netgear EX2700 fakeroot uImage
Change image name: "OpenWrt fakeroot" -> "LEDE fakeroot"

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2016-06-05 23:23:57 +02:00
Álvaro Fernández Rojas
29b412b8c5 ramips: add kmod-pwm-mediatek for mt7628/mt7688
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 13:24:25 +02:00
Álvaro Fernández Rojas
604b92dbd0 ramips: fix the number of uarts for each SoC
- Use default number of uarts (2) for rt288x/rt305x/rt3883/mt7620.
- Allow up to 3 uarts on MT7621 and MT7628.
- Remove unneeded SERIAL_8250_RT288X for MT7628.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 12:20:33 +02:00
Álvaro Fernández Rojas
243e79e10c ramips: fix Mi Wi-Fi Nano Wireless LED pinmux
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 12:19:57 +02:00
Álvaro Fernández Rojas
a105eac4dd kernel: update kernel 4.4 to version 4.4.12
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-02 15:34:34 +02:00
Yuan Chenmang
b38296f2f6 ramips: add Widora-NEO board support
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.

Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-01 12:52:28 +02:00
Joseph C. Lehner
2a589539ba ramips: fix Netgear EX2700 images
The previous image creation code would have failed if the
unpadded kernel uImage size was less than 64 bytes from the
next erase block boundary. Fix that.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2016-05-30 22:52:59 +02:00
Joseph C. Lehner
b232669d45 ramips: fix Netgear EX2700 images
The bootloader on this device expects the kernel partition to end
on a 64k boundary. The last 64 byte of the kernel partition must
contain a valid uImage header (the fakeroot partition).

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2016-05-27 15:50:18 +02:00
Álvaro Fernández Rojas
2a57a54d49 ramips: add backported MT7628 pinmux fixes
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-29 11:26:41 +02:00
Cezary Jackiewicz
af1e70b4a7 ramips: Add status led for Xiaomi MiWiFi Nano
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-23 22:43:37 +02:00
John Crispin
bf6634339a ramips: fix timing issues when using MT7621 spi
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-23 20:22:22 +02:00
John Crispin
c7efbd7dbb ramips: Add specific compatible properties for esw
Currently, for RT5350 and MT7628, esw is marked as compatible with
"ralink,rt3050-esw". While this is true, the switches within RT5350
and MT7628 actually support more functionality than the RT3050 switch.

One such example is per-VLAN untagging, which is an important feature.

RT3352 is another example of this, but it already has an additional
compatible property, which allows to differentiate it from RT3050.

This commit adds such more specific properties for RT5350 and MT7628
as well.

Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
2016-05-23 11:28:59 +02:00
Cezary Jackiewicz
2965430999 ramips: cleanup for Hame MPR-A2
- disable all ethernet ports except port 0 on MPR-A2

Port 0 is the only ethernet port on this router, so disable all other PHYs in order to save power.

- don't use a VLAN for the single ethernet port of the MPR-A2

Like A5-V11, this router only has one ethernet port.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-23 11:03:23 +02:00
Felix Fietkau
5166732a4e ramips: use green power LED as status indicator for Buffalo WSR-1166 and WSR-600
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-21 15:16:37 +02:00
Felix Fietkau
82dcbec727 ramips: remove fake vlan rx offload from ethernet driver
The network stack does not need it to do GRO

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-20 14:01:21 +02:00
Álvaro Fernández Rojas
3bc90f9626 ramips: use backported upstream patches
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-19 17:48:41 +02:00
Álvaro Fernández Rojas
638d509817 ramips: fix pinctrl regression
This regression was introduced in commit 9195d8da.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-18 22:08:39 +02:00
Álvaro Fernández Rojas
29db5cae43 ramips: fix spidev generic nodes
Use linux,spidev compatible string.
Move MZK-DP150N spidev to spi1 node.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-18 22:08:39 +02:00
Álvaro Fernández Rojas
021c893658 ramips: fix size-cells on spi nodes
size-cells should be 0 in order to avoid dummy values in reg properties.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-18 16:57:39 +02:00
John Crispin
2a6b899589 ramips: fix 8M WT3020 image creation
fix image size for 8M version : 4M -> 8M

Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
2016-05-16 20:59:06 +02:00
John Crispin
1d9c0b2409 ramips: fix ArcherC20i image creation - 3rd try
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-15 11:59:43 +02:00
Felix Fietkau
ce009d16a1 ramips: fix Archer C20i image build
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-15 14:11:26 +02:00
John Crispin
5d0eff9801 ramips: set default profile to priority 1
doing so will sort all profiles alphabetically

Signed-off-by: John Crispin <john@phrozen.org>
2016-05-14 21:27:16 +02:00
John Crispin
7697aced24 ramips: fix ArcherC20i image creation
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-14 21:26:05 +02:00
Felix Fietkau
27dfe64887 ramips/mt7621: remove cflags override
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-14 17:58:43 +02:00
Álvaro Fernández Rojas
20b069c440 ramips: disable unused ethernet ports on VoCore
Only ports 0 and 4 are used so disable the other ones in order to save power.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-14 12:40:03 +02:00
Felix Fietkau
7fab5dc486 ramips: fix indentation of Build/* template commands
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-12 19:49:38 +02:00
John Crispin
f10d2bb6d3 ramips: add wmac nodes to all mt7628/88 dts files
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
Andrew Yong
8c9b8d70b1 ramips: add status led for ZBT-WE826
Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-05-12 03:29:36 +02:00
John Crispin
4220cc3255 ramips: convert mt7620 to new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
John Crispin
ecbaaa401a ramips: convert mt7688 to new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
John Crispin
0f12f32996 ramips: convert mt7628 to new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
John Crispin
825717d450 ramips: convert mt7621 to new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
John Crispin
a55f0c32fa ramips: convert rt2880 to new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
Stanislav Galabov
ffaaa6788a ramips: DTS modifications
This commit makes the following modifications to ramips dts files:
1. Add clkctrl node to all dtsi files (although not used for now)
2. Add clocks and clock-names properties to some nodes (usbphy, pci)
3. Add usbphy node for rt3050 (although not used for now)
4. Add clock-frequency to uart nodes in mt7621.dtsi and mt7628an.dtsi

These modifications, although not fully used at the moment, will make
it easier for FreeBSD to adopt and use LEDE ramips dts files with
minimal changes for easier maintenance.

Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
2016-05-12 03:29:36 +02:00
John Crispin
b8ab6af1a9 global: change my email address
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
Andrew Yong
374cae9e6f ramips: add initial support for SamKnows SK-WB8
Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-05-12 03:29:35 +02:00
Stanislav Galabov
9195d8da35 ramips: DTS rework
Add node aliases to dtsi files.
Reword dts files so they're more in-line with upstream.
Fix some more warnings and errors reported by dtc

Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
2016-05-12 03:29:35 +02:00
Álvaro Fernández Rojas
e32b2f92b1 kernel: update kernel 4.4 to version 4.4.10
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-11 21:34:27 +02:00
John Crispin
f6059cc118 ramips: fix DTB generation
using preprocessor style includes when calling dtc directly.

Signed-off-by: John Crispin <john@phrozen.org>
2016-05-10 14:44:05 +02:00
Stanislav Galabov
f8b6c9d825 ramips: Change all '/include/' clauses to '#include' so preprocessing can
be done properly for the entire device trees.

Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
2016-05-10 10:43:17 +02:00
Stanislav Galabov
600c224213 ramips: Add hex prefix (0x) to dtsi reg properties where needed.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
2016-05-10 10:43:17 +02:00
Stanislav Galabov
b8f73d7f0a ramips: introduce serial0 aliases
This patch introduces serial0 aliases in the ramips DTS files, which can
then be used to denote the active console instead of relying on bootargs.

Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
2016-05-10 10:43:17 +02:00
Álvaro Fernández Rojas
b062266ad6 kernel: update kernel 4.4 to version 4.4.9
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-10 10:43:17 +02:00
D. Andrei Măceș
823c58a1cf ramips: mt7620: [UPSTREAM] fix USB frequency scaling
The logic for the SoC check got inverted. We need to check if it's
not a MT76x8.

Signed-off-by: D. Andrei Măceș <dmaces@nd.edu>
2016-05-10 10:43:13 +02:00
Vittorio Gambaletta (VittGam)
1570277094 ramips: Fix alphabetical sorting for 02_network
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2016-05-10 10:43:13 +02:00
Vittorio Gambaletta (VittGam)
39f035fdc7 ramips: Don't use a VLAN for the single ethernet port of the A5-V11.
This router only has one ethernet port, so a VLAN is useless here, now that the rt3050 TCP bug that happened without VLANs has been fixed for a very long time.

Add this router to the VLAN-less config that is used by other single-port routers.

Also fix MAC address detection code since this router has no WAN port.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2016-05-10 10:43:13 +02:00
Vittorio Gambaletta (VittGam)
ffb7bf7672 ramips: Fix network for routers without VLANs on eth0.
Some routers only have one port, so eth0 is used without VLANs for them.

Revision r47720 introduced some changes, but wrongly confused "enable" with "reset".

VLANs need to be disabled for those routers, and the switch may be reset.

Fix this, by explicitly disabling VLANs instead of resetting the switch for these routers.

Also merge duplicate configuration for the "m2m".

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2016-05-10 10:43:12 +02:00
blogic
40bfe9f0bd ramips: Drop hacky switch workaround for failsafe on rt3x5x and rt5350.
The new rt3050 switch driver doesn't have problems with TCP when not
using VLANs.

This piece of code also broke failsafe for all routers where the LAN
port is not wired to port 0 of the internal switch.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 49293
2016-05-10 10:43:12 +02:00
blogic
3f638902b6 ramips: Disable all ethernet ports except port 0 on A5-V11.
Port 0 is the only ethernet port on this router, so disable all other PHYs
in order to save power.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 49292
2016-05-10 10:43:12 +02:00
blogic
d5114b509b ramips: Disable all ethernet ports except port 4 on HT-TM02.
Port 4 is the only ethernet port on this router, so disable all other PHYs
in order to save power.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 49291
2016-05-10 10:43:12 +02:00
blogic
12758e32d3 ramips: Get rt3050 ethernet ports to be disabled from the device tree.
This patch allows configuring ports to be disabled in the device tree; this
saves power, since disabling ports here actually disables power to ethernet
PHYs.

Line 444 enables all ethernet ports, so line 487 is getting zero ports to be
disabled, except for port 5 in SoCs where this is not implemented as it will
be sticky disabled in register POC0. Because of this, the code will still read
the switch configuration and OR it to the device tree setting.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 49290
2016-05-10 10:43:12 +02:00
blogic
e626d4f702 ramips: Fix comment in rt3050 ethernet switch driver.
Line 444 is actually enabling all switch ports by setting the disable bits
to 0. This needs to be done because the bootloader sets all ports to disabled
by default (which is the case for at least one router based on RT5350).

So, this patch fixes the comment in line 443.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 49289
2016-05-10 10:43:12 +02:00
blogic
e716fce5da ramips: Fix documentation for the rt3050 switch driver.
The prefix used in the driver is now "mediatek" instead of "ralink".

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 49288
2016-05-10 10:43:12 +02:00
blogic
decd89c57f ramips: Fix multicast ICMPv6 for the rt3050 ethernet switch.
The FCT2 esw register should be set to 0x2500C to have "unknown IPv6
multicast" packets broadcasted to every port, instead of dropped.
The previous value only let those packets go through ports 1 and 3.

"Unknown IPv6 multicast" packets include packets needed by ICMPv6 echo
requests addressed to well-known addresses, such as ff02::1 (MAC address
is 33:33:00:00:00:01 in this case).

Please note that by default ICMPv6 echo requests to ff02::1 are not replied
to by the router because of ip6tables considering those packets to be invalid.
But this is another bug/patch. ;)

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 49287
2016-05-10 10:43:12 +02:00
blogic
6b0425a187 ramips: add support for Planex MZK-EX750NP.
add support for Planex MZK-EX750NP.
MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49268
2016-05-10 10:43:12 +02:00
John Crispin
dc92917409 image / basefiles: make console password configurable
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
Signed-off-by: John Crispin <john@phrozen.org>
2016-04-18 21:53:07 +02:00
Jo-Philipp Wich
e885286834 target: globally remove ARCH_PACKAGES overrides
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-04-17 19:55:09 +02:00
John Crispin
cb049e71cd ramips: Add support for the Netgear WNDR3700v5
https://wiki.openwrt.org/toh/netgear/wndr3700

wndr3700v5 uses the single-core dual thread MediaTek MT7621S SoC.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49247
2016-04-26 11:43:53 +00:00
John Crispin
279eeeb744 ramips: add support for Planex MZK-EX300NP
MZK-EX300NP is MT7620A based wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49235
2016-04-26 11:43:06 +00:00
John Crispin
e55d86ef32 ramips: add support for Planex CS-QR10
CS-QR10 is MT7620A based IP Camera.

the camera and sound does not work with kernel 4.4.
 - camera chip is sn9c291.
 - sound chip is wm8960.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49234
2016-04-26 11:43:01 +00:00
Hauke Mehrtens
657a2457a6 ramips: fix build of target
Makes the patches apply again by fixing the white space broken patch.
This problem was introduced in r49212.

Closes #22248 and #22259

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 49221
2016-04-24 22:17:38 +00:00
John Crispin
30fbc1a4d1 ramips: Add support for ZBT WG3526
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.

v1->v2:
* Remove some references to 2626 that I had missed in the dts.

v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>

SVN-Revision: 49213
2016-04-21 19:47:08 +00:00
John Crispin
a6c7c0029e ramips: awake rt305x USB controller
Because of Ralink uboot set USB controller into sleep mode [1]
we check it and awake controller before any registers access.
Fix ticket #21396 [2]

[1] http://marc.info/?l=linux-usb&m=137398626102108&w=2
[2] https://dev.openwrt.org/ticket/21396

Signed-Off-By: Serge Vasilugin <vasilugin@yandex.ru>

SVN-Revision: 49212
2016-04-21 19:47:02 +00:00
John Crispin
37b50fdb92 ramips: add support for ELECOM WRH-300CR
ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB
DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but
easy-to-access) UART.

it also has internal USB hub and USB card reader which provide one USB
port, one SD card slot, and one microSD card slot.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>

SVN-Revision: 49211
2016-04-21 19:46:59 +00:00
John Crispin
d2654729ac ramips: update DTS file for Planex DB-WRT01
update DTS files to use jedec,spi-nor compatible string for m25p80 to fix probe issues.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49209
2016-04-21 19:46:49 +00:00
John Crispin
890eb0c126 ramips: fix support Planex MZK-750DHP.
fix script for Planex MZK-750DHP.
modification of the GPIO definition.
add Profile.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49205
2016-04-20 17:19:05 +00:00
John Crispin
4a5158bd2a ramips: rt3352 usbphy fix in dts-file
Add missing rt3352 usb phy. Fix ticket #20499.

Signed-Off-By:Serge Vasilugin <vasilugin@yandex.ru>

SVN-Revision: 49204
2016-04-20 17:19:00 +00:00
Hauke Mehrtens
f0b3964f1b kernel: update kernel 4.4 to version 4.4.7
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 49176
2016-04-16 21:05:48 +00:00
John Crispin
3bf88dc041 ramips: remove accidentally comitted code
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 49161
2016-04-09 14:47:35 +00:00
John Crispin
8b8dfeb027 ramips: Disable the SD driver by default on MT7621
The SD driver has been a long and dragging issue on the MT7621 platforms as it hasn't worked for
months resulting in unbootable devices. Until it's fixed, disable it in the default profiles.

Reports / Discussed here:

https://dev.openwrt.org/ticket/21392
https://dev.openwrt.org/ticket/21834
https://dev.openwrt.org/ticket/21995
https://forum.openwrt.org/viewtopic.php?id=59092

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>

SVN-Revision: 49131
2016-04-09 10:25:03 +00:00
John Crispin
0ffa58009a ramips: Fixes for LinkIt 7688
Misc fixes for LinkIt 7688 board:

- Copy the right wireless firmware for the mt7688
- Add back '0065-mt7688-fixes.patch', left out after the move to Linux 4.4.
- Remove SPI_DEV from linux config which otherwise causes a massive warning
- Add wmac to LINKIT7688.dts so wireless works

Signed-off-by: Adam Kent <adam@semicircular.net>

SVN-Revision: 49130
2016-04-09 10:24:58 +00:00
John Crispin
3ad1820e83 ramips: Adjust image size limit for the D-Link DIR-860L B1
Currently the maximum image size defaults to 8Mbyte even though this model has 16Mbyte of flash memory.

Tested and works on my device.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>

SVN-Revision: 49129
2016-04-09 10:24:55 +00:00
John Crispin
1eb8b0674d ramips: fix for Planex MZK-WDPR (lcd control gpio).
add lcd control gpio pin for Planex MZK-WDPR.
LCD board initial timming is GPIO control.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49128
2016-04-09 10:24:52 +00:00
John Crispin
e626a0d877 ramips: mt7621: fix Ubiquiti EdgeRouter X profile
Remove unnecessary packages to reduce image size so it fits in initramfs (to enable upgrading from factory firmware).

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 49127
2016-04-09 10:24:47 +00:00
John Crispin
37f1022d73 ramips: mt7621: sync MQmaker WiTi profile name to dts name
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 49126
2016-04-09 10:24:44 +00:00
John Crispin
14177319ea ramips: enable device profiling by dts
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 49125
2016-04-09 10:24:40 +00:00
John Crispin
133f890a12 ramips: mt7621: add a device to TARGET_DEVICES after it's definition
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 49124
2016-04-09 10:24:36 +00:00
John Crispin
a9466914f5 ramips: mt7621: fix initramfs image for ubnt-erx
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 49123
2016-04-09 10:24:29 +00:00
John Crispin
79d02229cc ramips: move different subtarget image generation to separate makefiles to improve maintainability
- all subtarget specific defines are in their own files
- common defines left in main Makefile
- each subtarget makefile idefed with SUBTARGET
- all subtargets compile tested
- few seems to be broken/unneeded things marked with FIXME

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 49104
2016-04-01 07:11:48 +00:00
Gabor Juhos
fc5c19f45b ramips: lzma-loader: fix O32 ABI conformance
According to the calling convention of the o32 ABI the
caller function must reserve stack space for $a0-$a3
registers in case the callee needs to save its arguments.

The assembly startup code does not reserve stack space
for these registers thus when the main C function needs
to save its arguments, that will cause a stack overflow.

Fix the assembly code to reserve stack space for the
registers to avoid that.

Untested. It seems that the lzma-loader is not used at all?

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 49062
2016-03-21 13:15:29 +00:00
John Crispin
cc82da0bc1 ramips: MiWifi-Nano - change gpios to leds, add to default build group
1) Use leds to indicate:
Red - Power
Amber - Radio On
Blue - Wifi associated
2) Add profile to default build group for MT7628 subtarget

Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>

SVN-Revision: 49045
2016-03-20 14:41:33 +00:00
John Crispin
99414dbcf1 ramips: Add support for Xiaomi MiWiFi Nano
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash

Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>

v3  includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds

SVN-Revision: 49024
2016-03-16 09:26:48 +00:00
John Crispin
be79629259 ramips: Add support for GL-MT750
This patch adds support for GL-MT750.
GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps.
It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support.

SVN-Revision: 48994
2016-03-10 19:12:10 +00:00
John Crispin
be53e5a154 ramips: Add support for GL-MT300N
This patch adds support for GL-MT300N.
GL-MT300N is powered by MT7620N with 16MB flash, 64MB RAM,
2 LANs, USB, UART, GPIO and PoE support.

SVN-Revision: 48993
2016-03-10 19:12:04 +00:00
John Crispin
96ee39b184 ramips: Add support for GL-MT300A
This patches adds support for GL-MT300A.
GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM,
Two LANs, USB, UART and MMC daughter board.

SVN-Revision: 48992
2016-03-10 19:11:57 +00:00
John Crispin
1b9985cfe2 ramips: add support for Planex MZK-WDPR.
add support for Planex MZK-WDPR.
MZK-WDPR(MZK-WDPR-R01) is internet radio tuner.
This patch is "network board" in MZK-WDPR.
LCD board is non OpenWrt Platform.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 48968
2016-03-08 18:11:59 +00:00
Felix Fietkau
3abf5ce656 ramips: convert the remaining subtargets to 4.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48954
2016-03-07 17:56:53 +00:00
Felix Fietkau
f73d8fb81b ramips: fix subtarget kernel version assignment (only mt7621 is ready for now)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48953
2016-03-07 17:05:03 +00:00
Felix Fietkau
d041e8b44b ramips: add linux 4.4 support, update mt7621 subtarget to 4.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48951
2016-03-07 16:33:34 +00:00
John Crispin
77da9390da ramips: mt7621: fix WF-2881 for ubi split
This patch fix firmware split for WF-2881 which was previously manually partitioned.

Signed-off-by: YounJae Rho <luxflow@live.com>

SVN-Revision: 48908
2016-03-04 08:33:17 +00:00
John Crispin
9d828931f1 ramips: Add profiles for JCG routers
This patch adds profiles and support for building factory and
sysupgrade images for JHR-N805R, JHR-N825R and JHR-N926R.

Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>

SVN-Revision: 48906
2016-03-04 08:33:12 +00:00
John Crispin
43dd2b9965 ramips: Add JCG routers to base-files
This patch adds support for JHR-N805R, JHR-N825R and JHR-N926R to
various scripts in the base-files directory.

Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>

SVN-Revision: 48905
2016-03-04 08:33:09 +00:00
John Crispin
ca64f498f0 ramips: Add device tree for JCG JHR-N926R
Add a device tree for JCG JHR-N825R

This router is based on a RT3052 and has 4MB of CFI flash and 32MB of
SDRAM. As a special feature, it comes with a two digit seven segment
display that is connected to a pair of daisy-chained 74164 shift
registers that can be controlled via GPIOs.

For details, see https://wikidevi.com/wiki/JCG_JHR-N825R .

Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>

SVN-Revision: 48904
2016-03-04 08:33:06 +00:00
John Crispin
97ca4cbc94 ramips: Add device tree for JCG JHR-N825R
Add a device tree for JCG JHR-N825R

This router is based on a RT3052 and has 4MB of CFI flash and 32MB of
SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N825R .

Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>

SVN-Revision: 48903
2016-03-04 08:33:03 +00:00
John Crispin
73f4c3f2ab ramips: Add device tree for JCG JHR-N805R
Add a device tree for JCG JHR-N805R

This router is based on a RT3050 and has 4MB of SPI flash and 16MB of
SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N805R .

Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>

SVN-Revision: 48902
2016-03-04 08:33:00 +00:00
John Crispin
e4dc6acd31 ramips: Incorrect file mode change
Commit d0f5ab6d95a1 ("ramips: Added support for ZBT-826 / ZBT-1026")
incorrectly changed the mode of the ramips shell scripts from 755 to 644.
I.e., they are not excutable any more and for example devices will be left
with broken configs.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>

SVN-Revision: 48893
2016-03-03 20:24:45 +00:00
Felix Fietkau
15517811e4 ramips: enable mt76 on mt7688 by default
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48886
2016-03-02 17:40:58 +00:00
John Crispin
96eb5c6fa8 ramips: Added support for ZBT-826 / ZBT-1026
Support for these MT7620-based routers: https://wiki.openwrt.org/toh/zbt/we-826
Based on Oskari’s patches found here: https://dev.openwrt.org/ticket/19996

Signed-off-by: Jamie Stuart <jamie@onebillion.org>

SVN-Revision: 48865
2016-03-01 09:17:06 +00:00
Felix Fietkau
28458bd057 ramips: add sysupgrade support for mt7628
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48813
2016-02-28 15:46:27 +00:00
Felix Fietkau
dc6533d982 ramips: create device tree node for MT7628 WMAC in preparation for future work on driver support in mt76
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48812
2016-02-28 13:21:54 +00:00
John Crispin
f998540e80 ramips: fix GPIO names for RT5350F-OLinuXino-EVB
Hi,

the board in subject (RT5350F-OLinuXino-EVB) still ships from vendor
with a RC3 image built upon a .dts file which declares GPIO12 and GPIO14
as relay2 and relay1 respectively, as you can see from their rt5350f
branch on GitHub.

For some reason in the official stable build both the GPIOs are swapped
and the wrong names are declared in the gpio-export directive.

I'm submitting this patch which should roll back the wrong changes, so
that we get backward compatibility with any script developed on RC3
which controls the relays.

After patching correct operation is restored:

root@OpenWrt:/# cat /sys/kernel/debug/gpio
GPIOs 0-21, platform/10000600.gpio, 10000600.gpio:
 gpio-0   (button              ) in  hi
 gpio-12  (relay2              ) out lo
 gpio-14  (relay1              ) out lo

Thank you,

Signed-off-by: Lorenzo Cafaro <lorenzo@ibisco.net>

SVN-Revision: 48796
2016-02-26 08:35:35 +00:00
John Crispin
074cc7ac38 ramips: mt7620: fix failsafe switch config
As indicated in the bug tracker[1], failsafe mode is broken on at least some
devices using the mt7620 switch (and possibly mt7621). The thread explicitly
mentions the Xiaomi MiWifi, and the Nexx WT3020, and an unspecified device
using the mt7621 switch; the issue also applies to the Netgear EX2700.

The problem is that failsafe mode uses eth0, but enable_vlan is always set to 1
by the switch driver. Connecting to and/or pinging the device fails. This patch
fixes the failsafe preinit config, by making sure that vlan support is disabled.
It currently only fixes the switch config on mt7620, but might apply to the
mt7621 as well, so the patch has been designed with this in mind.

A similar (line wrapped) patch was submitted in December by Simon Peter, but never
accepted and/or discussed.

This patch applies to both Chaos Calmer and trunk.

[1] https://dev.openwrt.org/ticket/18768

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>

SVN-Revision: 48772
2016-02-25 10:14:22 +00:00
John Crispin
cb49742f99 ramips: build factory images for Netgear EX2700
This patch adds support for building factory and sysupgrade images
for the Netgear EX2700 that don't require modification of u-boot
environment variables.

The bootloader on this device expects the kernel partition to end
on a 64k block boundary. The last 64 byte of the kernel partition
must contain a valid uImage header - in the stock firmware, this is
the uImage header of the root filesystem. For this patch, we're using
the uImage header of a 0 byte partition (ex2700-fakeroot.uImage).

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>

SVN-Revision: 48771
2016-02-25 10:14:19 +00:00
Felix Fietkau
0ec9253b9d ramips: fix WSR-1166 partition table
- Fix typo in board_data partition start address
- Increase board_data partition size in order to exploit all flash size

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>

SVN-Revision: 48751
2016-02-22 08:54:32 +00:00
John Crispin
fc47eb0794 ralink: fix mt7628 ehci support
the u2_phy init was missing

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48747
2016-02-19 16:38:04 +00:00
John Crispin
1e218001b5 ralink: unbreak port4 on mt7620
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48746
2016-02-19 16:37:56 +00:00
John Crispin
8b38a9450b ramips: Add support for Phicomm PSG1208
This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram.
The WPS led is uesd as status_led because the power light can't be controlled with GPIO.
It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

SVN-Revision: 48721
2016-02-15 18:45:22 +00:00
John Crispin
ba53b33453 ramips: Support LEDs on D-Link DIR-860L B1
Adds the required gpio definitions.

Signed-off-by: Johannes Wienke <languitar@semipol.de>

SVN-Revision: 48715
2016-02-12 09:29:23 +00:00
John Crispin
9f9682a79b ramips: Add support for Netgear EX2700
This patch adds support for the Netgear EX2700 and builds an approriate
sysupgrade image.

What's missing is the option to build a factory image flashable via the
router's stock web interface, but this approach is hindered by the fact
that u-boot operforms an additional integrity check, which expects a
uImage header in the last 64 bytes of the "kernel" partition, which
the bootloader expects to be 960k, a size exceeded by the standard
OpenWrt kernel.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>

SVN-Revision: 48698
2016-02-12 08:29:33 +00:00
Felix Fietkau
6b73b7a8ec ramips: fix build error on oversized images by putting the dir-860l-b1 size check at the end of the chain
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48681
2016-02-08 19:18:21 +00:00
John Crispin
6801c4e33e ramips: HLK-RM04 - Enable GPIO14 for WPS button
The top half of UARTF on the HLK-RM04 is used for GPIO.

  mode 1   mode 2
   RIN     GPIO14
   DSR_N   GPIO13
   DCD_N   GPIO12
   DTR_N   GPIO11
   RXD     GPIO10
   CTS_N   GPIO09
   TXD     GPIO08
   RTS_N   GPIO07

This patch applies 3'b101 mode to UARTF:

   GPIO14
   GPIO13
   GPIO12
   GPIO11
   RXD
   CTS_N
   TXD
   RTS_N

Because the base rt5350.dtsi file forces 3'b000 mode, remove the pin setting from this file and apply it directly to the files that inherit from it (WIZFI630A.dts and WT1520.dtsi).  This change makes the rt5350.dtsi file consistent with the mt7620a.dtsi file.

Signed-off-by: John Clark <inindev@gmail.com>

SVN-Revision: 48665
2016-02-08 08:26:27 +00:00
John Crispin
7f672e66f8 rampis: HLK-RM04 - Setup I2C as GPIO
The I2C function of the RT5350 SoC on the HLK-RM04 is used for GPIO1 and GPIO2.

Take note that the I2C_SD pin is GPIO1 on the RT5350 and is exposed on the HLK-RM04 as GPIO0
Likewise the I2C_SCLK pin is GPIO2 on the RT5350 and is exposed on the HLK-RM04 as GPIO1

 group   mode 1    mode 2   hlk-rm04 pin & export
  i2c    i2c_sd    gpio1   (pin 8, hlk-rm04:gpio0)
  i2c    i2c_sclk  gpio2   (pin 9, hlk-rm04:gpio1)

reference:
  http://www.hlktech.net/product_detail.php?ProId=39
  http://cdn.sparkfun.com/datasheets/Wireless/WiFi/RT5350.pdf

Signed-off-by: John Clark <inindev@gmail.com>

SVN-Revision: 48664
2016-02-08 08:26:19 +00:00
John Crispin
480e15f2ce ramips: HLK-RM04 - Fix push button functions
The RESET button of the HLK-RM04 is connected to GPIO0, linux function 0x198
The WPS button of the HLK-RM04 is connected to GPIO14, linux function 0x211

Signed-off-by: John Clark <inindev@gmail.com>

SVN-Revision: 48663
2016-02-08 08:26:11 +00:00
John Crispin
1f26091242 ramips: HLK-RM04 - Remove power LED config
The power LED on the HLK-RM04 is hard wired to the power bus and is not under GPIO control, remove the bogus config for it.
(Note that GPIO0 is actually connected to the RESET button.)

Signed-off-by: John Clark <inindev@gmail.com>

SVN-Revision: 48662
2016-02-08 08:26:02 +00:00
Felix Fietkau
afdb24e3ae ramips: add IMAGE_SIZE to DEVICE_VARS, it is used by build templates
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48611
2016-02-01 17:41:29 +00:00
Felix Fietkau
705ddc9bb9 ramips: make tp-link firmware size errors non-fatal
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48526
2016-01-28 14:13:01 +00:00
Felix Fietkau
81e8e02289 ramips: fix image size checks for Buffalo WSR-1166 and WSR-600
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48508
2016-01-26 16:45:11 +00:00
Hauke Mehrtens
a29c7ca3d9 kernel: update kernel 4.3 to version 4.3.4
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 48498
2016-01-25 21:44:48 +00:00
Felix Fietkau
57776e68ce base-files: remove default /etc/config/network, generate it via board.d instead
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48493
2016-01-25 16:30:41 +00:00
Felix Fietkau
6f8d647778 ramips: re-enable highmem support for MT7621 now that it's fixed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48469
2016-01-24 00:16:32 +00:00
John Crispin
f51f92d7e9 ramips: fix serial baudrate for final version of ZBT-WG2626 board
The bootloader was updated and now uses 115200 instead of 57600 baud
for the serial console. Change this also in OpenWrt's DTS, so the rate
is consistent for bootloader and linux kernel output.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 48359
2016-01-19 10:16:30 +00:00
John Crispin
9f7bbc649c ramips: HiLink HLK-RM04 image name typo (RM02 -> RM04)
The image name for the HiLink HLK-RM04 module has a typo and should read "RM04" rather than "RM02"

Signed-off-by: John Clark <inindev@gmail.com>

SVN-Revision: 48355
2016-01-19 10:15:44 +00:00
Felix Fietkau
3c3fb1dfc0 ramips: delete the broken sound driver
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48318
2016-01-18 13:40:15 +00:00
Felix Fietkau
63aa7023d8 ramips: mark kmod-sound-mtk as broken, it does not compile properly
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48317
2016-01-18 13:22:38 +00:00
Felix Fietkau
fa61e3fbba ramips: fix kernel config handling for mt7620/mt7628 sound module
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48316
2016-01-18 13:22:34 +00:00
Hauke Mehrtens
cdb83aaf5f kernel/4.3: update to version 4.3.3
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de

SVN-Revision: 48224
2016-01-12 20:52:19 +00:00
Felix Fietkau
471a567a88 ramips: do not rely on $(BIN_DIR) installed files during image build (for ubnt-erx)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48147
2016-01-06 18:39:13 +00:00
Felix Fietkau
2499a57d92 targets: add kernel image dependencies on device tree files
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48146
2016-01-06 18:39:06 +00:00
Felix Fietkau
947eac1803 ramips: do not attempt to build ubnt-erx initramfs image if initramfs support is disabled
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48144
2016-01-06 18:38:44 +00:00
Felix Fietkau
56608a777e ramips: fix duplicate /dts-v1/ line for WRTNODE2
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>

SVN-Revision: 48138
2016-01-06 00:04:14 +00:00
Felix Fietkau
48a57b1ead ramips: set mips16 support
Signed-off-by: Cristian Morales Vega <cristian@samknows.com>

SVN-Revision: 48131
2016-01-04 22:35:36 +00:00
John Crispin
e85230ce2e ralink: add a few mt7688 fixes that got lost in the v4.3 bump
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48115
2016-01-04 14:21:24 +00:00
John Crispin
eb9fccc440 ralink: update the usb phy driver to the version sent upstream
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48114
2016-01-04 14:21:17 +00:00
John Crispin
9b675a2a33 ralink: fix USB compatible strings
switch to the upstream compatible strings for ehci and ohci support.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48113
2016-01-04 14:21:11 +00:00
Felix Fietkau
c69ffda546 ramips: clean up and refresh kernel patches
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48070
2016-01-02 14:48:27 +00:00
Felix Fietkau
140be9f1a5 ramips: fix performance counters on mt7621
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48069
2016-01-02 14:48:11 +00:00
John Crispin
fb2d204ce4 ralink: more esw_rt3050 fixes
the IRQ was not setup properly causing an oops

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48064
2016-01-02 11:44:08 +00:00
John Crispin
6ca6a98622 ramips: Remove LED GPIO definitions in MQmaker WiTi device tree
LED's were defined wrong in the device tree file, they are hardware driven because they are connected directly to the switch chip and wireless chips respectively, thus no GPIO addresses are assigned to them. It is safe to remove them from the device tree file to stop confusion.

Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>

SVN-Revision: 48055
2016-01-01 21:20:54 +00:00
John Crispin
de7dce21a3 ralink: add WRTnode2 platform and led support
Signed-off-by: xzmu <xzmu@wrtnode.com>

SVN-Revision: 48049
2016-01-01 21:19:50 +00:00
John Crispin
6b95386fd3 ralink: fix rt3050/5350 ethernet switch support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48030
2016-01-01 21:17:21 +00:00
Felix Fietkau
c55d8d4253 ramips: set the wifi mac address to the same as LAN on witi
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48029
2016-01-01 18:58:02 +00:00
Felix Fietkau
eaf8889cf8 ramips: add a script to fix up the broken mac address on the witi board
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48027
2016-01-01 18:57:39 +00:00
Felix Fietkau
46519964ff kernel: fold of_get_mac_address_mtd into of_get_mac_address
This makes it easier to keep drivers in sync with upstream

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48026
2016-01-01 18:57:29 +00:00
Felix Fietkau
22693a9086 ramips: fix kernel configuration for mt7628
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48025
2016-01-01 15:20:38 +00:00
Felix Fietkau
f3bbb73a20 ramips: add missing clk_round_rate function to fix buildbot errors
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48024
2016-01-01 14:33:09 +00:00
Felix Fietkau
28ec4e0e71 ramips: fix inverted LEDs for RE6500
Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>

SVN-Revision: 48022
2016-01-01 12:27:45 +00:00
Felix Fietkau
2c4faaed74 ramips: add mac address assignment for eth0 on RE6500
Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48021
2016-01-01 12:26:38 +00:00
Felix Fietkau
d65eda48b7 ramips: fix firmware partition size
Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>

SVN-Revision: 48020
2016-01-01 12:26:30 +00:00
Felix Fietkau
11c697015f ramips: fix memory size for RE6500
Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>

SVN-Revision: 48019
2016-01-01 12:26:26 +00:00
Felix Fietkau
3e807886d0 ramips: disable NAND device in mt7621.dtsi to fix boot errors on many devices
Enable it from .dts files that need it, also remove redundant properties

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47936
2015-12-19 11:07:29 +00:00
Felix Fietkau
32877b31dc ramips: update DTS files to use jedec,spi-nor compatible string for m25p80 to fix probe issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47935
2015-12-18 22:26:40 +00:00
John Crispin
4afe0fc2b2 ralink: update the mt7621 ethernet support patch
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47929
2015-12-17 12:14:56 +00:00
John Crispin
7de7bd0201 ramips: mt7621: fix error message when initramfs is too large
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47908
2015-12-17 09:27:09 +00:00
John Crispin
1c5136c4c3 ramips: remove unwanted change from patch
Remove unwanted change to irq-mips-gic.c from mt7621 support patch

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47907
2015-12-17 09:27:00 +00:00
John Crispin
43422a634b ramips: change CM_GCR_BASE_CMDEFTGT_MEM value to match datasheet
Zero config value for default memory region means 'memory', not
not 'disabled' according to 'Control Registers Of The Coherency
Manager' manual.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47906
2015-12-17 09:26:51 +00:00
John Crispin
acbed0eff3 ramips: mt7621: undo mips-cm probe hack to not wipe out memory regions
Since now we hopefully setup memory regions properly we no longer need this hack.

Tested and works on ubnt-erx.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47905
2015-12-17 09:26:43 +00:00
John Crispin
622e268710 ramips: mt7621: setup memory region for pcie controller memory
Only compile tested since I do not have any hardware with
devices on pcie bus.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47904
2015-12-17 09:26:35 +00:00
John Crispin
e8890c6be0 ramips: mt7621: add patch to setup CM memory region for palmbus
This is tested and works on ubnt-erx.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47903
2015-12-17 09:26:28 +00:00
John Crispin
b4bb10b3a0 ralink: update config files to build the cleaned up ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47902
2015-12-17 09:26:20 +00:00
John Crispin
402db12f1a ralink: drop dummy profile from mt7688
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47901
2015-12-17 09:26:09 +00:00
John Crispin
651e620de5 ralink: fixup devicetree files to work with new ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47900
2015-12-17 09:25:57 +00:00
John Crispin
fa854a02a1 ralink: drop old ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47899
2015-12-17 09:25:30 +00:00
John Crispin
31116661ff ralink: add reworked ethernet driver
update to the version of the driver that is on its way upstream

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47898
2015-12-17 09:25:24 +00:00
John Crispin
5d4f5689fd ramips: add missing kernel symbols
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47884
2015-12-12 21:01:02 +00:00
John Crispin
4e31b2e869 ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)
This router is based on MT7621 SoC, no wifi, no usb, nand.

Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.

Doesn't work:
* No GPIO leds. All leds are controlled by switch,
  but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.
* PoE out.

Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.

U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.

Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
John Crispin
1c6c9549d6 ramips: add support for Spansion S34ML0[24]G2 flash
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47880
2015-12-12 07:37:53 +00:00