Remove SUPPORTED_DEVICES from wr841-v9 because it´s not needed and
for consistency rename everything to tl-wr841-v9.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Add ath9k wifi capabilities to WNDR3700 family.
* use kmod-owl-loader to load firmware from "art"
* add wifi to DTS
* add wifi LEDs
Avoid using the same MAC for eth0 LAN and wlan0 by
toggling the eth0 MAC into a locally administered MAC.
That is currently done by in user-space by adding a
uci config item into /etc/config/network
(More elegant solution might be setting it already in
preinit phase.)
Known issues:
* wifi firmware file may not get created on the first boot
after flashing on time to bring wifi normally up. Likely
the overlay jffs2 is not yet ready for creating the
firmware file. "wifi up" may still bring wifi up.
Wifi will work normally at subsequent boots.
* phy0 and phy1 may get assigned mixed, so that phy0 may
be the 5GHz radio instead of the normal 2.4GHz, and vice
versa for phy1. Does not happen always, but may happen.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[fix the wifi unit address in the dts]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Pisen WMM003N (sold under the name of Cloud Easy Power) is an
AR9331-based router and power bank combo device. The device uses a
stock firmware modified from OpenWRT for TP-Link TL-WR703N; however
some GPIO definition is different on this device with TL-WR703N. An
AXP202 PMIC (connected to a 5000mAh battery) and a SD slot are also
added, and the stock Flash/RAM configuration is 8MiB/64MiB.
The stock firmware is an old and heavily modified OpenWRT-based
firmware, which has telnetd defaultly open, and the root password is
"ifconfig" (quotation marks not included). The factory image format is
not known yet, however the stock firmware ships the OpenWRT's sysupgrade
command, and it can be used to install a newer firmware.
Due to the lack of the access to the STM8 embedded controller, the SD
slot is currently not usable (because it's muxed with the on-board USB
port) and the AXP PMIC cannot be monitored.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
This router is called RE450 and the tl prefix was used to identify it
as a TP-Link device. Drop the tl prefix since we now have tplink in
dts and device name.
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
PLL for eth0 internal clock on ar913x is at 0x18050014
and AR913X_ETH0_PLL_SHIFT is 20 instead of 17
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Add support for WNDR3700 and WNDR3700v2.
They share most things with WNDR3800.
Only device IDs and partition structure needs to be set.
Note: WNDR3700 (v1) has no NETGEAR_HW_ID, but has
also the NA version of the factory image.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Prepare for addition of WNDR3700 and WNDR3700v2 by
separating the common parts into wndr3700.dtsi and
leaving just the device-specific things into wndr3800.dts
The three routers are identical except
* device IDs
* WNDR3700 (v1) has only 8 MB flash, while others have 16 MB.
Partition structure needs to be defined for each device.
* (WNDR3800 has 128 MB RAM, but RAM size is not in DTS)
Also separate the common parts of the image recipe.
(Drop also the initramfs recipe.)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.
Specification:
- Qualcomm Atheros QCA9557
- 128 MB of RAM
- 16 MB of Flash
- 2.4/5 GHz wifi
- 2.4 GHz: 2T2R (SoC internal)
- 5 GHz: 3T3R (QCA9880)
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AC1600DGR2
2. Connect power cable to WN-AC1600DGR2 and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch copies over the MAC patching helper functions from lantiq's
target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom
file.
Not all vendors bothered to write the correct MAC addresses for the
ath9k wifi into the calibration data. And while ath9k does have some
special dt-properties to extract the addresses from a fixed position,
there are still devices that require userspace to edit or modify
the caldata.
In my case, the MAC address for the Wi-Fi device is stored in an
unsorted key-value based "nvram" database and there's an existing
userspace tool to extract the data.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Bit 8/12 of reset controller which is marked as PHY_RESET/SWITCH_RESET
in datasheets will trigger either a reset for builtin switch or assert
an external ETH0_RESET_L/ETH1_RESET_L pin, which are usually connected
to external PHY/switch. None of them should be triggered every time an
interface is brought up in ethernet driver.
Remove PHY reset support from ag71xx and definition for them in dtsi.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Buffalo BHR-4GRV2 is a wired router, based on Qualcomm Atheros
QCA9558.
Ported from ar71xx target.
Specification:
- Qualcomm Atheros QCA9558
- 64 MB of RAM
- 16 MB of Flash
- 5x 10/100/1000 Ethernet
- QCA8337N
- 4x LEDs, 2x keys
- UART header on PCB
- Vcc, TX, RX, GND from LED side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of BHR-4GRV2
2. Connect power cable to BHR-4GRV2 and turn on it
3. Access to "http://192.168.12.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新実行")
button
5. Wait ~120 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This adds PLL settings for the ethernet ports of the TP-Link TL-WR1043
v2/v3 and the Openmesh OM5P-AC-v2.
We also change the PLL-settings in the qca9557.dtsi to match the ones
used as default on the ar71xx target.
As of 4b9680f138 those devices have broken ethernet ports as the default
PLL settings defined in the QCA9557.dtsi are applied which are off for
those devices.
Signed-off-by: David Bauer <mail@david-bauer.net>
commit 4b9680f fixed pll settings and the correct pll set
by bootloader is overrided by value in qca9557.dtsi which
is incorrect for Archer C7 and breaks ethernet. Add pll
values for archer c7 to fix ethernet connection.
This individual pll tweak has been cherry picked from github pr 1260
which changes a couple of things in a single commit and should be
ideally split. This commit get archer v7 back and working.
Tested: archer c7 v2
Original combined commit authored by:
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
c7 fix only split out by:
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The QCA9557 dtsi is currently missing pll-handle and pll-regs for both
eth0 and eth1, therefore PLL settings won't be applied. This commit
fixes this behavior.
Signed-off-by: David Bauer <mail@david-bauer.net>
Including the tl-wdr3600 image build code just to overwrite most of it
doesn't make much sense and only makes it hard to read.
Furthermore, the tl-wdr4300 image will be marked as compatible with the
tl-wdr3600 this way.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The variables are used in image build recipes and need to be marked as
per devices vars to be stored individual per image define. Otherwise
the last defined variable will be used for all boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch did the following things:
1. Separate ath9k-leds out of gpio leds so that all other leds will work
before ath9k loded (e.g. during preinit/init stage).
2. Rename wps led to qss since that's how TP-Link mark it.
3. Rename LED prefix to tp-link because that dts is shared by many devices.
4. Rename to wr740n-v1 because v1 is the first and v2 just use the fw of v1.
(This will require a forced sysupgrade if you comes from
the previous wr740n v2 image.)
5. Remove SUPPORTED_DEVICES.
(tl-wr740n-v2 doesn't exist anywhere so it's useless.)
6. Add all WR741ND v1 clones found in ar71xx.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Fix all issues found by the devicetree compiler like wrong address/size
cells as well as wrong/missing/superfluous unit addresses.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use only the jedec,spi-nor compatible string. Everything else either
never worked or is only support to keep compatibility.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This router is called Archer C7 and the tl was used to identify
TP-LINK. Since we have added tplink in dts/board name, the tl
prefix is useless now.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Change lan and it's LED to eth0
It's broken since c7c807cb8c
where I changed the dts but forgot to change default configurations.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
1. Swap eth0/eth1
Both devices are using AR9331, the builtin switch on AR9331 is
connected to gmac1 and gmac1 is named as eth1 in ath79.
PS: gmac1 is eth0 and gmac0 is eth1 in ar71xx because of the
reversed initialization order.
2. Fix the incorrect compatible string in dts
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
phy-handle is used to poll link status. They are useless when
we need fixed-link on these interfaces.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Without this patch you will get an error "gpio-export probe deferral
not supported" when you try to export i2c expander gpio pins.
gpio-export is probed long before i2c-bus and i2c expander are created
and it doesn't retry it so none pins are exported.
Signed-off-by: René van Dorst <opensource@vdorst.com>
apply the change to all instances of the gpio exports patch
Signed-off-by: Mathias Kresin <dev@kresin.me>
Revert 290c54473e ("ath79: fix TP-Link Archer C7 v2 wlan1 MAC address")
which obviously aims to have a distinct MAC address per interface.
Unfortunally it doesn't match what is used by the stock firmware and we
shouldn'z use MAC Adresses not reserverd for/assigned to a particular
board.
The correct MAC adress increments for this board are:
wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1
Fixes: FS#408
Signed-off-by: Mathias Kresin <dev@kresin.me>
The PowerCloud Systems CR3000 was a cloud-managed CPE for a now defunct
NaaS offering. It was previously supported under the ar71xx branch and
this forward ports that support with some notable differences:
1) Since reverting to stock firmware is now irrelevant there is is only
a single openwrt image generated which uses the entire flash rather than
preserving PowerCloud-specific partitions that are unneeded to openwrt--
those partitions will be erased and used by the openwrt image.
2) Rather than use a non-standard probe order for the ethernet devices,
this image uses a set of 'ip link set ethX name ethY' commands very early
in preinit (before the network is used at all), in order to have the the
switch and Wan use the same ethernet names as in previous images.
3) /etc/config/wireless will need to be regenerated as the path to the
wireless device has changed due to differences in ath79 DT for ar93x
compared to ar71xx images.
4) eth0 is wan and eth1 is lan (switch)
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
In the new DT-based pci-ar71xx driver, ar71xx_pci_irq_init() was being
called before populating the PCI controller's device_node struct member.
This led to no IRQ being assigned to connected PCI devices (e.g. ath9k
cards) and caused them to be non-functional aside from simply being
detected.
The previous errors encountered in dmesg were: "irq: no irq domain found
for /ahb/apb/pcie-controller@180c0000 !". /proc/interrupts listed an IRQ
of 0 for the cards.
While this has been only been tested on a yet-to-be-merged RouterStation
Pro target, it should also fix the broken wifi people have reported for
the ath79 WNDR3800 target.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
mdio bus isn't a standalone device on ar7240. (and maybe older SoCs?)
Use simple-mfd for ar7241 and later SoCs to get mdio1 ready before gmac0
For ar7240 and older chips, manually create platform device after
ag71xx_hw_init() in ag71xx_probe()to get mdio0 ready between
ag71xx_hw_init() and ag71xx_phy_connect().
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Allow specifying desired mdio clock frequency in dts.
Use default frequency around 5MHz for builtin switch and 2MHz for other mdio bus.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
